1. የምርት መግቢያ

Handwheel working power supply voltage	DC24V/1A
ተቀባዩ የኃይል አቅርቦት Vol ልቴጅ	DC24V/1A
Receiver IO output load range	DC24V
Hand wheel end cable length	10m
Receiver end cable length	1m
Receiver end network cable length	3m
Operating temperature	-25℃<X<55℃
Anti-fall height	1m
Custom Button Quantity	6
Product dimensions	233*90.7*77.4（mm）

4.የምርት ተግባር መግቢያ

ማስታወሻ:

Emergency stop button:

የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, እና በተቀባዩ ላይ ሁለቱ የአደጋ ጊዜ ማቆሚያዎች ስብስብ ይለያያል, and all functions of the handwheel will be invalid.

After releasing the emergency stop, the emergency stop IO output on the receiver is closed, and all functions of the handwheel are restored.

② Screen display:

6.2 የመቀበያ ጭነት መጠባበቂያ ልኬቶች

6.3 Installation dimensions of aviation plugs

6.4 የተቀባዩ የሽቦ ንድፍ ንድፍ
7.Product Operation Instructions

1. When the receiver is powered on and the working indicator light of the receiver flashes, connect the receiver to the computer with a network cable, set the fixed IP address of the computer, and use the network configuration tool software to set the network parameters of the handwheel function. For specific setting methods, refer to the “LXWGP-ETS Wired Handwheel User Manual”.

2.After the receiver is set up, the system needs to program a PLC program. Please refer to the “LXWGP-ETS Different Siemens Numerical Control System Setting Methods” and PLC program routine materials for details.

3.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.

4.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X interface of the system. Connect the receiver power supply and pulse line.

5. Select axis selection: Switch the axis selection switch and select the axis you want to operate on.

6. ማጉያ ማጉላት ይምረጡ: Switch the magnification switch and select the magnification level you need.

7. ዘንግ ማንቀሳቀስ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, የአክስ ምርጫ ማብሪያ / ማጥፊያ ይምረጡ, የማጉያ ማጉያ ማብሪያ / ማጥፊያ ይምረጡ, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.

8. Press and hold any custom button to turn on the IO output of the corresponding button in the receiver, and release the button to turn off the output.

9. የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, ተቀባዩ ተጓዳኝ የአደጋ ጊዜ ማቆሚያ አዶ ውፅዓት ይቋረጣል, የእጅ ሥራው ተግባር ይሰናከላል, የአደጋ ጊዜ ማቆሚያ ቁልፍን ይልቀቁ, የአደጋ ጊዜ ማቆሚያ io ውፅዓት ይዘጋል, and the handwheel function will be restored.

8.የምርት የሞዴል መግለጫ

9.Product trouble shooting

1.የምርት መግቢያ

2. የምርት ተግባራዊ ባህሪዎች

3. የምርት ዝርዝሮች

Voltage ልቴጅ እና የገመድ አልባ ሩቅ	3V / 14MA
የባትሪ ዝርዝሮች	2 AA ALKILINEANTINES, size 5
ዝቅተኛ የ voltage ልቴጅ ማንቂያ ደወል ገመድ አልባ ሩቅ	< 2.3V
ተቀባዩ የኃይል አቅርቦት Vol ልቴጅ	DC5V -2V / ሀ
ተቀባዩ የአስቸኳይ ጊዜ ማቆሚያ ውፅዓት ጭነት ክልል	Ac125V-1A / DC30ቪ-2 ሀ
ተቀባዩ የውጤት ጭነት ክፈናትን ያንቁ	Ac125V-1A / DC30ቪ-2 ሀ
የተቀባዩ የዱር አዝራር የውጤት ጭነት ክፍያ	DC24V / 50A
ተቀባዩ የአክሲስ ምርጫ ውፅዓት ጭነት ክልል	DC24V / 50A
ተቀባዩ ማብራሪያ የውጤት ውፅዓት ጭነት ክልል	DC24V / 50A
በእጅ የተቆራረጠው ስርጭት ማስተላለፍ ኃይል	15DBM
ተቀባዩ የስሜትነት ይቀበላል	-100DBM
ገመድ አልባ የግንኙነት ድግግሞሽ	433የ MHZ ድግግሞሽ ባንድ
ሽቦ አልባ የግንኙነት ርቀት	የመከላከያ ነፃ ርቀት 40 ሜትር
የአሠራር ሙቀት	-25℃ < X < 55℃
ፀረ ውድቀት	1 (ሜትር)
ብጁ አዝራር ብዛት	2

4. የምርት ተግባር መግቢያ

ማስታወሻዎች:

① pulsh Colder:
የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, የልብ ምት, የ pulse pulse ምልክት,and control the movement ofthe machine axis.
② ቁልፍን ያንቁ:
በሁለቱም በኩል ያለውን ቁልፍ ያንቁ, እና በሁለት ተቀባዩ ላይ ያሉት ሁለት ስብስቦች ያካሂዳል. የቃላቱን ለማላቀቅ የቃላቱን ማንቃት የቃላትን ቁልፍ ይልቀቁ; እና የአክስ ምርጫን ማጉያ ከማዛመድዎ በፊት እና የእጅ ህ / ንጣፍ ከማንቀፍዎ በፊት,የተዘበራረቀ ቁልፍ ውጤታማ ለመሆን መያዙ አለበት; This function can be cancelled through configuration software.

③ አመልካች መብራቶች:
ግራ የጎን ብርሃን: በብርሃን ላይ ኃይል,የእጅ ወረቀቱ ለኃይል እንዲመርጡ ዘንግ ይጠቀማል, እናም ይህ ብርሃን ከስልጣን በኋላ ይቆያል;
የመካከለኛ ብርሃን: በማንኛውም የእህት እጅ ሥራ በሚሠራበት ጊዜ የሚያበራ ምልክት ብርሃን, አጥር በሌለበት ጊዜ አይበራም;
የቀኝ የጎን ብርሃን: ዝቅተኛ የ voltage ልቴጅ ማንቂያ መብራት, ዝቅተኛ የባትሪ ደረጃ,ይህ ቀለል ያለ ወይም ይቀጥላል, battery needs to be replaced.

④ የአደጋ ጊዜ ማቆሚያ ቁልፍ:
የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, እና በተቀባዩ ላይ ሁለቱ የአደጋ ጊዜ ማቆሚያዎች ስብስብ ይለያያል, and all functions of the handwheel will be invalid.

⑤ ማጉላት መቀያየር:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ የአክሲ ምርጫ ማብሪያ ማብሪያ (የኃይል ማብሪያ):
የአክሲስ ምርጫ ማብሪያ ማብሪያ / ማጥፊያ ለመቀየር የቃላቱን ቁልፍ ተጭነው ይያዙ, ይህም እንቅስቃሴን በእጅ የሚቆጣጠር እንቅስቃሴን መለወጥ ይችላል. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ ብጁ ቁልፍ:
ሁለት ብጁ አዝራሮች, each corresponding to an IO output point on the receiver.

5. የምርት ተካፋይ ሥዕላዊ መግለጫ

6. የምርት መጫኛ መመሪያ
6.1 የምርት ጭነት ደረጃዎች

1. ተቀባዩ በጀርባው ላይ በተቀባዩ የኤሌክትሪክ ካቢኔ ውስጥ ይጫኑት, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. የእኛን ተቀባዩ የሽቦ ንድፍ ማውጫውን ይመልከቱ እና ከጣቢያዎ መሣሪያዎችዎ ጋር አነፃፅረው. Connect the equipment to the receiver via cables.
3.ተቀባዩ በትክክል ከተስተካከለ በኋላ, ተቀባዩ የተስተካከለ አንቴና ተገናኝቷል, እና የአንቴሪ ውጫዊ መጨረሻ መጫን ወይም ከኤሌክትሪክ ካቢኔ ውጭ መቀመጥ አለበት. ለበለጠ የምልክት ውጤት በኤሌክትሪክ ካቢኔ አናት ላይ እንዲያስቀምጠው ይመከራል. አንቴናን ያልተስተካከለ ወይም በኤሌክትሪክ ካቢኔ ውስጥ ማስቀመጥ መተው የተከለከለ ነው, as this may result in the signal being unusable.
4. በመጨረሻ, የእጆቹን የኃይል ማብሪያ ማብሪያ / ማጥፊያ / ማጥፊያ, and you can operate the machine remotely using the handwheel.

6.2 የመቀበያ ጭነት መጠባበቂያ ልኬቶች

6.3 የተቀባዩ የሽቦ ንድፍ ንድፍ

7. የምርት ኦፕሬሽን መመሪያዎች
1. በማሽኑ ላይ ያለው ኃይል እና ተቀባዩ. የተቀበሉት የሥራ ድርሻ አመላካች ቀላል ብልጭታዎች. ባትሪውን በገመድ አልባ የኤሌክትሮኒክስ ህንድ ውስጥ ይጭሩት, የባትሪውን ሽፋን ይጠብቁ, እና
የገመድ አልባ የኤሌክትሮኒክስ ህትፊን ቁጥር የኃይል መቀያየር ላይ ያብሩ. The handwheel’s battery level indicator light is on.
2. አስተባባሪው አረም ይምረጡ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, የአክስ ምርጫ ማብሪያ ማብሪያ, and select the axis you want to operate.
3. ማጉያ ማጉላት ይምረጡ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, ማጉያውን ማብሪያ / ማጥፊያ,and select the desired magnification level.
4. ዘንግ ማንቀሳቀስ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, የአክስ ምርጫ ማብሪያ / ማጥፊያ ይምረጡ, የማጉያ ማጉያ ማብሪያ / ማጥፊያ ይምረጡ, እና ከዚያ የልብ ምትዎን ማሽከርከር. ለማንቀሳቀስ የሰዓት አቅጣጫ አቅጣጫ ያሽከርክሩ
positive axis and counterclockwise to move the negative axis.
5. ማንኛውንም ብጁ ቁልፍን ተጭነው ይያዙ, እና ተቀባዩ የተቀበሉት የአጻጻፍ ቁልፍ አዮ ፅፅር በርቷል. አዝራሩን ይልቀቁ, and the output will be turned off.
6. የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, ተቀባዩ ተጓዳኝ የአደጋ ጊዜ ማቆሚያ አዶ ውፅዓት ይቋረጣል, የእጅ ሥራው ተግባር ይሰናከላል,የአደጋ ጊዜ ማቆሚያ ቁልፍን ይልቀቁ, የአደጋ ጊዜ ማቆሚያ io ውፅዓት ይዘጋል, and the handwheel function will be restored.
7. የእጅ ወረቀቱ ለተወሰነ ጊዜ ካልተሰራ, የኃይል ፍጆታ ለመቀነስ በራስ-ሰር የእንቅልፍ ሁኔታ ያስገባል. እንደገና ጥቅም ላይ ሲውል, the handwheel can be activated by pressing the enable button.
8. የእጅ ወረቀቱ ለረጅም ጊዜ ጥቅም ላይ ካልዋለ, ወደ ውጭ ቦታው ወደ ውጭ ቦታ ለመቀየር ይመከራል, የእጅ ወረቀቱን ያጥፉ, and extend the battery life.

8. የምርት የሞዴል መግለጫ

① :ZTWGP የአዕምሮ ዘይቤን ይወክላል
②：የ pulse የውጽዓት መለኪያዎች:
01: የ pulse ውፅዓት ምልክት ሀ, ለ; Poll ልቴጅ 5V; pulse quantity 100PPR.
02：የጅምላ ውፅዓት ምልክቶችን የሚያመለክቱ ሀ እና ቢ; Poll ልቴጅ 12V; pulse quantity 100PPR.
03：የጅምላ ውፅዓት ምልክቶችን የሚያመለክቱ ሀ, ለ, ሀ -, ለ -; Poll ልቴጅ 5V; pulse quantity 100PPR.
04：ዝቅተኛ-ደረጃ NPN ክፍት የወረዳ ውፅዓት ያሳያል, የ pulse የውበት ምልክቶች የ A እና ለ;The number of pulses is 100PPR.
05：የከፍተኛ ደረጃ የ PNP ምንጭ ውፅዓት ያሳያል, የ pulse የውበት ምልክቶች የ A እና ለ; The number of pulses is 100PPR.
③：የአክስ ምርጫን መቀየሪያዎች ብዛት ይወክላል, 2 ይወክላል 2 axes.
④：የአክሲስ ምርጫ ማብሪያ ምልክትን አይነት ይወክላል, አንድ ውክልና ነጥብ-እስከ-ነጥብ ውበት ምልክት, and B represents encoded output signal.
⑤：የማባባከሪያ ማባዛት ምልክትን አይነት ይወክላል, አንድ ውክልና ነጥብ-እስከ-ነጥብ ውበት ምልክት, and B represents encoded output signal.
⑥：የብጁ አዝራሮችን ቁጥር ይወክላል, 2 ይወክላል 2 custom buttons.
⑦：ለስርዓቱ ህንድ የሚገኘውን የኃይል አቅርቦት ይወክላል, እና 05 represents 5V power supply.
⑧：L ግራውን አምድ ይወክላል (የግራ አጭበርባሪ), እና r ትክክለኛውን ረድፍ ይወክላል (የቀኝ ቢላዎች መያዣ).

9.ለምርቶች መፍትሄዎች መፍትሄ

1.የምርት መግቢያ

Wireless electronic handwheel is used for manual guidance, አቀማመጥ, tool alignment,and other operations on CNC machine tools. ይህ ምርት ገመድ አልባ የማስተላለፍ ቴክኖሎጂን ይደግፋል, eliminating the traditional spring wire connection, በኬብሎች ምክንያት የመሳሪያ ውድቀቶችን መቀነስ, eliminating the disadvantages of cable dragging and oil stains, and making operation more convenient. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. የምርት ባህሪዎች
1. 433mhz ሽቦ አልባ የግንኙነት ቴክኖሎጂን ይቀበሉ, ገመድ አልባ አሠራር ርቀት ነው 40 ሜትር;
2. አውቶማቲክ ድግግሞሽ የመደናገጥ ተግባር, መጠቀም 32 sets of wireless remote controllers at the same time without affecting each other;
3. የአደጋ ጊዜ ማቆሚያ ቁልፍን ይደግፉ, የ ioy የምልክት ውፅዓት ቀይር, connected to the system through IO wiring;
4. ድጋፍ 4 ብጁ አዝራሮች, switch IO signal, output signal to the system through IO-LINK protocol;
5. Support quick movement button + and button -, press and hold the button to replace the handwheel to move the machine;
6. 6-የአክስ ቁጥጥር ይደግፉ, switch IO signal, output signal to the system through IO-LINK protocol;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

ማስታወሻዎች:
①Emergency stop button:
የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 ብጁ አዝራሮች, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.

5.የምርት መለዋወጫዎች ሥዕላዊ መግለጫዎች

6.የምርት መጫኛ መመሪያ

6.1 የምርት ጭነት ደረጃዎች

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.የእኛ ተቀባዩ የሽቦ ንድፍን ይመልከቱ, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3. ተቀባዩ ከተስተካከለ በኋላ, ተቀባዩ የተስተካከለ አንቴና ተገናኝቷል,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
ለበለጠ የምልክት ውጤት በኤሌክትሪክ ካቢኔ አናት ላይ እንዲያስቀምጠው ይመከራል. It
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4.በመጨረሻ, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 የመቀበያ ጭነት መጠባበቂያ ልኬቶች

6.3 የተቀባዩ የሽቦ ንድፍ ንድፍ

7. Maintenance and care

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
the service life;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. እባክዎን እንዳይጨርሱ ያድርጉ, መውደቅ, ማደንዘዝ, ወዘተ. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. ለረጅም ጊዜ ጥቅም ላይ የማይውል ከሆነ, እባክዎን የእጅዎን ንፁህ እና ደህንነቱ በተጠበቀ ቦታ ያከማቹ;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. Please read the instructions carefully before use. Non-professionals are prohibited from
operating.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. ጥገና ከተጠየቀ, እባክዎን አምራቹን ያነጋግሩ. If the damage is caused by self-repair,
the manufacturer will not provide warranty.

1.የምርት መግቢያ

Wireless electronic handwheel is used for manual guidance, አቀማመጥ, tool setting and
other operations of CNC machine tools. ይህ ምርት ገመድ አልባ የማስተላለፍ ቴክኖሎጂን ይደግፋል,
eliminating the traditional spring wire connection, በኬብሎች ምክንያት የመሳሪያ ውድቀቶችን መቀነስ,
eliminating the disadvantages of cable dragging, oil stains, ወዘተ, and is more convenient to
operate. It is widely used in CNC machine tools such as gantry machining centers, gantry
vertical lathes, CNC gear processing machines, and can be adapted to a variety of CNC
systems on the market, እንደ አይሲዎች ያሉ, ሙትቡሺ, Fancuc, syntec and other CNC system
brands.

2.የምርት ባህሪዎች

1. 433mhz ሽቦ አልባ የግንኙነት ቴክኖሎጂን ይቀበሉ, ገመድ አልባ አሠራር ርቀት ነው 80 ሜትር;
2. አውቶማቲክ ድግግሞሽ የመደናገጥ ተግባር, መጠቀም 32 sets of wireless remote controllers at the
same time without affecting each other;
3. የአደጋ ጊዜ ማቆሚያ ቁልፍን ይደግፉ, and after the handwheel is turned off, the emergency stop
button is still valid;
4. ድጋፍ 6 ብጁ አዝራሮች, የ ioy የምልክት ውፅዓት ቀይር;
5. 6-የአክስ ቁጥጥር ይደግፉ, 7-12 የአክሲስ ቁጥጥር ሊበጁ ይችላል;
6. 1x ይደግፋል 1x,10X, 100X ቁጥጥር እና ከፍተኛ ልበ ደንዳና 1000x ሊሆን ይችላል;
7. Supports the enable button function, output switch l0 sianals. axis selection,maanification
and encoder.;
8. Support axis selection and magnification selection encoder output;
9. Support standard Type-C charging, 5V-2A charging specification, built-in battery specification
14500/1100mAh.

3.የምርት ዝርዝሮች

4.የምርት ተግባር መግቢያ

ማስታወሻዎች：
①Emergency stop button：
When the emergency stop button is pressed, the two emergency stop IO outputs on
the receiver are disconnected, and all handwheel functions are invalid. When the emergency
stop is released, the emergency stop IO output on the receiver is closed, and all handwheel
functions are restored; and after the handwheel is turned off, the emergency stop IO output
of the receiver is still valid when the emergency stop button is pressed.

②Enable button:
Press any one of the enable buttons on both sides, and the two groups of enable IO
outputs on the receiver will be turned on. Release the enable button and the enable IO
output will be turned off. In addition, you need to press and hold the enable button before
switching the axis selection ratio and shaking the handwheel. This function can be
canceled through the configuration software.
③Axis selection switch (የኃይል ማብሪያ):
Press and hold the enable button and switch the axis selection switch to switch the
moving axis controlled by the handwheel. Switch this switch from OFF to any axis and
turn on the handwheel power.

④Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.

⑤Battery indicator:
The hand wheel power display, all bright means full power, all off means it is not
turned on or has no power, the first left grid flashes, indicating that the power is too low,
please charge in time.
⑥Signal Lights:
If the signal light is on, it means the handwheel is being operated and the signal is
normal; if the signal light is off, it means there is no operation, or it is being operated but
the wireless signal is not connected.

5.የምርት መለዋወጫዎች ሥዕላዊ መግለጫዎች

6.የምርት መጫኛ መመሪያ

6.1 የምርት ጭነት ደረጃዎች
1. Install the receiver in the electrical cabinet using the clips on the back, or install it in
the electrical cabinet using the screw holes at the four corners of the receiver.
2.የእኛ ተቀባዩ የሽቦ ንድፍን ይመልከቱ, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3.ተቀባዩ ከተስተካከለ በኋላ, ተቀባዩ የተስተካከለ አንቴና ተገናኝቷል,
እና የአንቴሪ ውጫዊ መጨረሻ መጫን ወይም ከኤሌክትሪክ ካቢኔ ውጭ መቀመጥ አለበት. It
is recommended to place it on the top of the electrical cabinet for the best signal effect. It is
forbidden to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4. በመጨረሻ, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 የመቀበያ ጭነት መጠባበቂያ ልኬቶች

6.3 የተቀባዩ የሽቦ ንድፍ ንድፍ

7.Product Operation Instructions
1. The machine is powered on, the receiver is powered on, the receiver working indicator
light flashes, the wireless electronic handwheel has the battery installed, the battery cover
is fastened, the wireless electronic handwheel power switch is turned on, እና
handwheel power light is on;
2. አስተባባሪው አረም ይምረጡ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, switch the axis selection
switch, and select the axis you want to operate on;
3. ማጉያ ማጉላት ይምረጡ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, switch the magnification switch,
and select the magnification level you need;
4. ዘንግ ማንቀሳቀስ: የተዘበራረቀውን ቁልፍ ተጭነው ይቆዩ, የአክስ ምርጫ ማብሪያ / ማጥፊያ ይምረጡ, select
the magnification switch, and then rotatethe pulse encoder to rotate the positive moving axis
clockwise and the negative moving axis counterclockwise;
5. ማንኛውንም ብጁ ቁልፍን ተጭነው ይያዙ, and the corresponding button IO output of the
receiver will be turned on. Release the button to turn off the output;
6. የአደጋ ጊዜ ማቆሚያ ቁልፍን ይጫኑ, the corresponding emergency stop IO output of the
receiver is disconnected, the handwheel function is disabled, release the emergency stop
አዝራር, the emergency stop IO output is closed, and the handwheel function is restored;
7. የእጅ ወረቀቱ ለተወሰነ ጊዜ ካልተሰራ, it will automatically enter sleep
mode to reduce power consumption. እንደገና ጥቅም ላይ ሲውል, the handwheel can be
activated by pressing the enable button;
8. የእጅ ወረቀቱ ለረጅም ጊዜ ጥቅም ላይ ካልዋለ,it is recommended to switch the handwheel
shaft to the OFF position, የእጅ ወረቀቱን ያጥፉ, and extend the battery life.

8.የምርት የሞዴል መግለጫ

① ：DWGP represents the appearance style

② ：የ pulse የውጽዓት መለኪያዎች:
01: Indicates that the pulse output signals are A and B, and the pulse voltage is 5V; Pulse
quantity 100PPR;
02: Indicates that the pulse output signals are A and B, and the pulse voltage is 12V; Pulse
quantity 25PPR;
03: Indicates that the pulse output signal is A B、A-、B-； Poll ልቴጅ 5V; Pulse quantity 1
00PPR;
04: ዝቅተኛ-ደረጃ NPN ክፍት የወረዳ ውፅዓት ያሳያል, የ pulse የውበት ምልክቶች የ A እና ለ; የ
number of pulses is 100PPR;05: የከፍተኛ ደረጃ የ PNP ምንጭ ውፅዓት ያሳያል, pulse output signals
are A and B; pulse quantity is 100PPR;
③ : represents the number of axis selection switches, 6 ይወክላል 6 ዘንግ, 7 ይወክላል 7 axis.
④ : represents the type of axis selection switch signal, አንድ ውክልና ነጥብ-እስከ-ነጥብ ውበት ምልክት,
B represents encoded output signal;

⑤ : represents the type of magnification switch signal,
አንድ ውክልና ነጥብ-እስከ-ነጥብ ውበት ምልክት, B represents encoded output signal;
⑥ : represents the number of custom buttons, 6 ይወክላል 6 ብጁ አዝራሮች;
⑦ : represents the power supply for the system handwheel, 05 5V የኃይል አቅርቦትን ይወክላል,
እና 24 represents 24V power supply.

9.Product Troubleshooting

10. Maintenance and care

1. እባክዎ በክፍል ሙቀት እና የአገልግሎት ህይወቱን ለማራዘም በክፍል ሙቀት እና ግፊት ውስጥ በደረቅ አካባቢ ውስጥ ይጠቀሙበት;
2. የአገልግሎት ህይወቱን ለማራዘም እንደ ዝናብ እና የውሃ አረፋዎች ያሉ ያልተለመዱ አከባቢዎች ውስጥ ካሉ አይቁ;
3. የአገልግሎቱን ህይወቷን ለማራዘም እባክዎን የእጅ የእጅ ስራውን መልቀቅ ይጠብቁ;
4. እባክዎን እንዳይጨርሱ ያድርጉ, መውደቅ, ማደንዘዝ, ወዘተ. to prevent damage to the precision components inside
the handwheel or accuracy errors;
5. ለረጅም ጊዜ ጥቅም ላይ የማይውል ከሆነ, እባክዎን የእጅዎን ንፁህ እና ደህንነቱ በተጠበቀ ቦታ ያከማቹ;
6.በማጠራቀሚያው እና በመጓጓዣ ወቅት, attention should be paid to moisture and shock resistance.

11.የደህንነት መረጃ

1. ከባለሙያ ያልሆኑ ባለሙያዎችን ከመጠቀምዎ በፊት እና መከልከልዎን በጥንቃቄ ያንብቡ;
2. When the battery level is too low, please charge it in time to avoid errors caused by insufficient
battery and inability to operate the handwheel;

3. ጥገና ከተጠየቀ, እባክዎን አምራቹን ያነጋግሩ. ጉዳቱ የሚከሰት ከሆነ በግለሰቦች ጥገና ከተከሰተ, the manufacturer will not provide warranty.

ሞዴል：ATWGP-12

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, CNC LASES, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, CNC LASES, traveling machine tools, መቆራረጥ እና ሌሎች መተግበሪያዎች, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, ሙትቡሺ, Fancuc, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 ሜትር;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-ዘንግ, 8-ዘንግ, 9-ዘንግ, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, ወዘተ;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. ዝቅተኛ የኃይል ፍጆታ ዲዛይን, 2 AA batteries can be used for more than 1 ወር;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

ማስታወሻ:
1. Status indicator light:
Signal light (ግራ): The signal light is always on when the handwheelis operated, and does not light up when not operating;
ዝቅተኛ የ voltage ልቴጅ ማንቂያ መብራት (ቀኝ): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.

1.Introduction of remote control

a.Product Composition
Siemens real-time coordinate display wireless electronic handwheel consists of two parts: electronic handwheel + receiver;

b.Characteristics

*6 custom buttons can control 6 switch outputs;
*The display screen displays the PLC corresponding register coordinate value in real time, and supports 6-axis display of real-time coordinates.

2.Application field

1）Electronic handwheel is connected to PLC via Ethernet receiver

a.The handwheel transmits the key data wirelessly to the receiver, and the receiver writes the keys through the network cable PLC system DB area; the receiver reads the data to be displayed from the designated DB area, and then returns the data to the handwheel display screen. The user can customize the base address of reading and writing DB area on the handwheel, so that the handwheel can read and write the data in the DB area of the PLC.

b. The receiver supports Siemens S7 protocol. Applies to PLC S7-200, PLC S7-300 and PLC S7-1200.

c. The user can configure the receiver to server mode and client mode through the PLC connection configuration tool.

In the server mode, the user configures the PLC read and write address through the WGP-ETS configuration software;Use the PLC connection configuration tool to configure the receiver into client mode. After configuration, the XWGP-ETS receiver can communicate with the PLC through the standard S7 protocol.

2)Specific application

Specific application of handwheel receiver and Siemens PLC S7-200:

a. The button on the handwheel corresponds to the value of the BOOL area set by the user in the PLC. If the button of the handwheel is pressed, the corresponding BOOL area is true, and when it is released, it is false, and the base address of the BOOL area can be set through the handwheel;

b. The handwheel can read the value of the DB area in the PLC. One axis has 4 bytes of display data, እና 6 axes have a total of 24 bytes. The base address of the DB area can be set through the WGP-ETS configuration software.

4.Appearance introduction

5.Receiver terminal definition and coding table

6.Appearance size

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, CNC LASES, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, CNC LASES, traveling machine tools, መቆራረጥ እና ሌሎች መተግበሪያዎች, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, ሙትቡሺ, Fancuc, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 ሜትር;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-ዘንግ, 8-ዘንግ, 9-ዘንግ, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, ወዘተ;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. ዝቅተኛ የኃይል ፍጆታ ዲዛይን, 2 AA batteries can be used for more than 1 ወር;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

ማስታወሻ:
1. Status indicator light:
Signal light (ግራ): The signal light is always on when the handwheelis operated, and does not light up when not operating;
ዝቅተኛ የ voltage ልቴጅ ማንቂያ መብራት (ቀኝ): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.