O bell di -wifr pwrpasol ar gyfer cyfarwyddiadau gweithredu turn fertigol CNC

① Pulse encoder:
Pwyswch a dal y botwm galluogi, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Low voltage alarm light, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Pwyswch y botwm stopio brys, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (Newid pŵer):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, rhaid cysylltu'r antena sydd â'r derbynnydd, and the outer end of the antenna should be installed or placed outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for the best signal effect. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Olaf, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Dimensiynau Gosod Derbynnydd

6.3 Diagram cyfeirio gwifrau derbynnydd

7. Product operation instructions
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, a
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Dewiswch yr echel gyfesuryn: Pwyswch a dal y botwm galluogi, toggle the axis selection switch, and select the axis you want to operate.
3. Dewiswch Chwyddiad: Pwyswch a dal y botwm galluogi, toggle the magnification switch,and select the desired magnification level.
4. Echel Symud: Pwyswch a dal y botwm galluogi, dewiswch y switsh dewis echel, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Pwyswch a dal unrhyw botwm arfer, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Pwyswch y botwm stopio brys, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. Os na weithredir yr olwyn law am gyfnod o amser, it will automatically enter sleep mode to reduce power consumption. Pan fydd yn cael ei ddefnyddio eto, the handwheel can be activated by pressing the enable button.
8. Os na ddefnyddir yr olwyn law am amser hir, it is recommended to switch the handwheel shaft to the OFF position, Diffoddwch y pŵer olwynion llaw, ac ymestyn oes y batri.

8. Disgrifiad o'r Model Cynnyrch

① :ZTWGP represents the appearance style
②：Paramedrau allbwn pwls:
01: Indicates that the pulse output signal is A, B; Foltedd pwls 5v; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Foltedd pwls 5v; pulse quantity 100PPR.
04：Yn nodi allbwn cylched agored NPN lefel isel, gyda signalau allbwn pwls o A a B.;The number of pulses is 100PPR.
05：Yn dynodi allbwn ffynhonnell PNP lefel uchel, gyda signalau allbwn pwls o A a B.; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 gynrychioli 2 axes.
④：Represents the type of axis selection switch signal, Mae A yn cynrychioli signal allbwn pwynt i bwynt, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, Mae A yn cynrychioli signal allbwn pwynt i bwynt, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 gynrychioli 2 Botymau Custom.
⑦：Represents the power supply for the system handwheel, a 05 yn cynrychioli cyflenwad pŵer 5V.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions