Paglalarawan
1.Modelo ng produkto
Modelo: DH12S-P6S
Naaangkop na kagamitan:Wire saw/blade saw machine
2.Diagram ng mga accessory ng produkto
Tandaan: Maaari kang pumili ng isa sa tatlong mga antenna. Ang antena ng suction cup ay pamantayan sa pamamagitan ng default.
3.Paglalarawan ng Remote Control Switch
4.Panimula ng DisplayContent
Pangunahing bilis ng motor: Pangunahing: 0-50
Ang bilis ng paglalakbay sa motor: Linya: 0-50
Pinakamataas na limitasyon ng bilis ng awtomatikong pagputol ng naglalakbay na motor: Bilis: 0-30
(nababagay ang mga parameter)
Awtomatikong pagputol ng pangunahing setting ng motor kasalukuyang: Setting: 28 (nababagay ang mga parameter)
Bilis ng motor ng swing braso: Swing: 0-50
Mababang boltahe: Ang baterya ng remote control ay masyadong mababa, Mangyaring palitan ang baterya.
Bumagsak ang network: Ang wireless signal ay nagambala. Mangyaring suriin ang lakas ng tatanggap, i -kapangyarihan ito muli, at i -restart ang remote control.
5.Mga tagubilin sa operasyon ng Remote Control Function
1） I -on ang remote control
Kapag ang tatanggap ay pinapagana, Ang ilaw ng D2 power sa tatanggap ay palaging nasa, at ang ilaw ng signal ng D1 ay nagsisimula sa pag -flash; Mag -install ng dalawang baterya ng AA sa remote control, I -on ang switch ng kuryente, At ang display ay magpapakita ng bilis ng motor, nagpapahiwatig ng matagumpay na pagsisimula.
2） Malaking regulasyon ng motor at bilis/pangunahing regulasyon ng motor at bilis
Pindutin at hawakan “Paganahin ang regulasyon ng bilis”, Lumiko ang “Pasulong/baligtad” Lumipat sa pasulong, At ang pangunahing motor ng tatanggap ay i -on;
Pindutin at hawakan “Paganahin ang regulasyon ng bilis”, Lumiko ang “Pasulong/baligtad” Lumipat upang baligtarin, At ang pangunahing motor ng tatanggap ay baligtad at i -on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Paikutin ang “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Pindutin at hawakan “Speed Adjustment Enable”, Lumiko ang “Pasulong/baligtad” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Lumiko ang “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Pindutin at hawakan “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Pindutin at hawakan ang “speed adjustment enable” pindutan at paikutin ang “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “pasulong/baligtad” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (Ipinagbabawal ang mga gumagamit na baguhin ito nang walang pahintulot)
Enter the parameter menu:Sa manu -manong mode, when the main motor speed is 0, Itulak ang pasulong/reverse switch up ng tatlong beses sa isang hilera, and then push it down three times in a row to enterthe parameter menu;
Lumabas sa menu ng parameter: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, default 800, unit milli second,Ipinagbabawal ang pagbabago;
Parameter ng Deceleration: Kapag ang pagputol ng kasalukuyang halaga ng pagbabago ay lumampas sa halagang ito, rapid deceleration begins, unit Ampere;
Acceleration A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Deceleration A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, Ipinagbabawal ang pagbabago;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, Ipinagbabawal ang pagbabago;
Pinakamataas na kasalukuyang: The range of main motor feedback current, unit Ampere;
Pinakamataas na host: Remote control main motor speed adjustment display range;
Pinakamataas na paglalakad: Invalid parameter;
Bilis ng limitasyon ng bilis: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Awtomatikong paggupit, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
6.Remote control na mga katangian ng elektrikal
7.Laki ng Remote Control
Ang pangwakas na interpretasyon na karapatan ng produktong ito ay kabilang lamang sa aming kumpanya.
