Roƙo:Musamman da aka yi amfani da shi don farjin waya
1.Yana goyan bayan aikin yankan atomatik, automatically adjusts cutting speed according to motor current feedback
2.Nesa-nesa-free watsawa shine 200 ma'aurata.
3. Goyon bayan direba na DC.
4. Yana goyan bayan saiti na yankan yankan, Irin wannan yankan halin yanzu, Yanke iyakar sauri, riƙaƙa.
5. Yana goyan bayan sauya tsakanin waya da ruwa ya taɓa canzawa. Za'a iya saita sigogi daban-daban.
Abin ƙwatanci: DH12S-P6S
Kayan aiki da aka zartar:wire saw/blade saw machine
Wasiƙa: Kuna iya zaɓar ɗaya daga cikin ukun ukun. An antenna na kofin cuptenna shine daidaitaccen ma'auni.
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(sigogi daidaitacce)
Automatic cutting main motor setting current: Setting: 28 (sigogi daidaitacce)
Swing arm motor speed: Swing: 0-50
Low wutar lantarki: Baturin sarrafawa na nesa ya yi ƙasa, Da fatan za a maye gurbin baturin.
Cibiyar sadarwa ta ragu: An katse siginar mara waya. Da fatan za a duba ikon mai karɓar, Iliminsa a sake, kuma sake kunna ikon nesa.
1）Turn on the remote control
Lokacin da mai karɓa ya kasance akan, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; Sanya baturan AA biyu a cikin ikon nesa, kunna kunna wutar lantarki, and the display will show the motor speed, yana nuna farawa mai nasara.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, Juya “Gabatarwa / baya” Sauya zuwa gaba, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, Juya “Gabatarwa / baya” Sauya zuwa juyawa, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Juya da “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, Juya “Gabatarwa / baya” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Juya “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” canji, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Latsa ka riƙe “speed adjustment enable” Button kuma juya “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “Gabatarwa / baya” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (An hana masu amfani daga canza shi ba tare da izini ba)
Enter the parameter menu:A cikin yanayin jagora, when the main motor speed is 0, tura gaba / baya juyawa sau uku a jere, and then push it down three times in a row to enterthe parameter menu;
Fita menu na sigari: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, ƙin cika alƙawari 800, unit milli second,An haramta gyara;
Rashin kunya: Lokacin da yankan canji na yanzu ya wuce wannan darajar, rapid deceleration begins, unit Ampere;
Hanzari A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Yaudarar A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, An haramta gyara;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, An haramta gyara;
Matsakaicin halin yanzu: The range of main motor feedback current, unit Ampere;
Matsakaicin rundunar: Remote control main motor speed adjustment display range;
Mafi girman tafiya: Invalid parameter;
HUKUNCIN HUKUNCIN SAUKI: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Atomatik yanka, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;guda ɗaya: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
Fassarar ƙarshe ta wannan samfurin mallakar kamfaninmu ne kawai.
