Dedye san fil aleka pou CNC Vètikal Operasyon Thorne Enstriksyon

① Pulse encoder:
Peze epi kenbe bouton an pèmèt, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Low voltage alarm light, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Peze bouton pou kanpe ijans lan, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (switch pouvwa):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

1. Enstale reseptè a nan kabinè elektrik la nan bouk la sou do a, oswa enstale li nan kabinè a nan twou yo vis nan kat kwen yo nan reseptè a.
2. Gade nan dyagram fil elektrik reseptè nou an epi konpare li ak ekipman sou-sou sit ou. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, dwe konekte antèn ekipe ak reseptè a, and the outer end of the antenna should be installed or placed outside the electrical cabinet. Li rekòmande pou mete l sou tèt kabinè elektrik la pou pi bon efè siyal la. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Anfen, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Dimansyon enstalasyon reseptè

6.3 Dyagram referans fil elektrik reseptè

7. Enstriksyon operasyon pwodwi yo
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, ak
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Chwazi aks kowòdone a: Peze epi kenbe bouton an pèmèt, toggle the axis selection switch, and select the axis you want to operate.
3. Chwazi agrandisman: Peze epi kenbe bouton an pèmèt, toggle the magnification switch,and select the desired magnification level.
4. Aks k ap deplase: Peze epi kenbe bouton an pèmèt, chwazi switch la seleksyon aks, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Peze epi kenbe nenpòt bouton koutim, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Peze bouton pou kanpe ijans lan, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. Si volan an pa opere pou yon peryòd de tan, it will automatically enter sleep mode to reduce power consumption. Lè yo itilize li ankò, the handwheel can be activated by pressing the enable button.
8. Si volan an pa itilize pou yon tan long, it is recommended to switch the handwheel shaft to the OFF position, fèmen pouvwa handwheel la, epi pwolonje lavi batri a.

8. Pwodwi Modèl Deskripsyon

① :ZTWGP represents the appearance style
②：Paramèt pwodiksyon batman kè:
01: Indicates that the pulse output signal is A, B; Batman kè vòltaj 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Batman kè vòltaj 5V; pulse quantity 100PPR.
04：Endike yon pwodiksyon sikwi louvri NPN ki ba, ak siyal pwodiksyon batman kè A ak B;The number of pulses is 100PPR.
05：Endike wo nivo pwodiksyon sous PNP, ak siyal pwodiksyon batman kè A ak B; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 reprezante 2 axes.
④：Represents the type of axis selection switch signal, A reprezante siyal pwodiksyon pwen-a-pwen, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, A reprezante siyal pwodiksyon pwen-a-pwen, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 reprezante 2 bouton koutim.
⑦：Represents the power supply for the system handwheel, ak 05 reprezante ekipman pou pouvwa 5V.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions