Akwukwo icho oru:Ejiri igwe eji egwuri egwu
1.Na-akwado ọnọdụ akpaka, na-emegharị ọsọ ọsọ na-aga nke obere moto dị ka nnukwu moto dị ugbu a, ma nweta njikwa akpaka.
2.Ahịrị na-enweghị nchekwa 200 mize.
3. Na-akwado usoro usoro ọsọ ọsọ maka nnukwu ọgba aghara na obere ọgbaghara.
4. Na-akwado obere moto na-atụgharị ebe.
5. Na-akwado obere ụgbọ ala na aka nri.
Mogosi: DH12S-LD
Akụrụngwa etinyere:crawler wire saw machine
Dee: Can nwere ike ịhọrọ otu n'ime antennas atọ ahụ. Abron iko bụ ọkọlọtọ na ndabara.
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (paramita na-agbanwe agbanwe)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
Voltaji dị ala: Batrị dịpụrụ adịpụ dị oke ala, Biko dochie batrị.
Network adaala: A na-egbochi mgbaàmà ikuku. Biko lelee ike nke onye na-anabata ya, ike ya ọzọ, ma malitegharịa ebe njikwa.
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Tụgharịa na-agbanwe ike, andthe display will show the motor speed, na-egosi mmalite nke ịga nke ọma.
2.Large motor and speed regulation
Tụgharịa “Gaanụ / ntụgharị” Gbanwee gaa n'ihu, the receiver’s large motor will turn on, and the display will show forward
Tụgharịa “Gaanụ / ntụgharị” Gbanwee na-atụgharị, the large motor of the receiver will turn on in reverse, and the display will show reverse
Bugharia nke “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “Gaanụ / ntụgharị” Gbanwee gaa n'ihu, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
Tụgharịa “Gaanụ / ntụgharị” Gbanwee na-atụgharị, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
Tụgharịa “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
Tụgharịa “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
Na ntuziaka mode:
Turn left in place: Pịa ma jide “Enable” mkpochi efe, Tụgharịa “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: Pịa ma jide “Enable” mkpochi efe, Tụgharịa “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” bọtịnụ ma bugharia nke “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.Mbelata akpaka
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Na ntuziaka mode, press and hold the “Enable” bọtịnụ ma bugharia nke “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (Amachibidoro ndị ọrụ iji gbanwee ya na-enweghị ikike)
Some functions of the remote control can be adjusted through parameters. Na ntuziaka mode, when the small motor speed S2 is 10, na-ebugharị / ntụgharị ugboro atọ n'usoro, and then push it down three times in a row to enter the parameter menu;
Wepụ menu: choose to save or not save, then press the enable button to confirm the exit;
Kachasị ugbu a: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, odida mkwa 800, Amachibidoro mgbanwe;
Isi oke: automatic cutting control parameter. Mgbe ịtọpụ uru ugbu a karịrị uru a,deceleration begins.
Osooso A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Nchọta A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Iri ije: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Mgbasa ọsọ ọsọ: the maximum speed of the small motor during automatic cutting.
Ndị ọbịa kachasị: maximum speed of large motor.
Isi mmalite ikpeazụ nke ngwaahịa a bụ naanị maka ụlọ ọrụ anyị.
