1.Pambuka Produk

2.Fitur Produk

Pencet terus tombol Aktifake, then toggling the axis selection switch can control the movement of axis .Press and hold the enable button, then toggle the axis selection switch to switch the motion axis controlled by the remote control. Toggle the switch from the OFF position to any axis position, and the remote control will power on automatically.

④ Pulse Encoder:

Press and hold the enable button and rotate the pulse encoder, it will output pulse signals to control the movement of the machine axis.

⑤ LCD Display Screen:

5. Product Accessories Diagram

 

6. Pandhuan instalasi Produk

6.1 Langkah-langkah instalasi Produk

1. Install the receiver in the electrical cabinet via the buckle on its back, or mount it inside the electrical cabinet through the screw holes at the four corners of the receiver.

2. Rujuk diagram kabel panrima kita, Bandhingake karo peralatan ing situs sampeyan, and connect the equipment to the receiver with cables.

3. After the receiver is fixed in place, install the supporting antenna of the receiver properly. Mount or place the outer end of the antenna outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for optimal signal performance. Do not leave the antenna uninstalled or place it inside the electrical cabinet; yen ora, signal failure may occur.

4. Pungkasane, turn on the remote control power switch, then you can remotely operate the machine via the remote control.

6.2 Receiver Installation Dimensions

6.3 Diagram referensi wiring wiring panrima

7. Pandhuan operasi produk

1. Daya ing mesin lan panrima. The receiver operation indicator flashes. After the wireless electronic remote control is fully charged, toggle it from the OFF gear to the X-axis gear, and the remote control display lights up.

2. Select the axis : Pencet terus tombol Aktifake, toggle the axis selection switch to select the axis to be operated.

3. Select the magnification: Pencet terus tombol Aktifake, toggle the magnification switch to select the required magnification gear.

4. Axis movement: Pencet terus tombol Aktifake, select the axis selection switch and the magnification switch, then rotate the pulse encoder. Rotate clockwise to move the axis in the positive direction, and rotate counterclockwise to move the axis in the negative direction.

5. Pencet terus tombol apa wae, the corresponding button IO output of the receiver will turn on; release the button, and the output will turn off.

6. Pencet tombol mandeg darurat, the corresponding emergency stop IO output of the receiver disconnects and the remote control function becomes invalid. Release the emergency stop button, the emergency stop IO output closes and the remote control function is restored.

7. If the wireless remote control is not operated for a period of time, bakal kanthi otomatis mlebu mode turu kanggo nyuda konsumsi daya. It can be used normally again by pressing the enable button again.

8.If the wireless remote control is not used for a long time, turn the axis switch to OFF to turn off the power and extend battery life

8. Katrangan Model Produk

①：UWGP stands for appearance style.

②：Pulse Output Parameters：

05: Nuduhake output sumber PNP sing dhuwur, Kanthi sinyal output pulsa saka A lan B; The number of pulses is 100PPR.

③：Represents the axis selection switch quantity; 6 stands for 6 Axes, 7 stands for 7 Axes, and so on.

④: Represents the signal type of the axis selection switch.A stands for point-to-point output signal, and B stands for encoder output signal.

⑤: Represents the signal type of the magnification switch.A stands for point-to-point output signal, and B stands for encoder output signal.

⑥: Nggantosi nomer tombol khusus; 3 corresponds to 6 custom buttons.

⑦: Represents the power supply for the system remote control. 05 stands for 5V power supply, lan 24 stands for 24V power supply.

⑧: Represents the contact charging mode. It starts charging automatically when placed back on the charging base.

9. Ngatasi masalah produk

 

10. Maintenance and upkeep

1. Please use it in a dry environment at room temperature and pressure to extend its service life.

2. Please avoid using in abnormal environments such as rain and water to extend the service life.

3. Please keep the appearance of the remote control clean to extend its service life.

4. Please avoid crushing, dropping, or bumping, lsp. to prevent damage to the precision components inside the remote control or accuracy errors.

5. Yen ora digunakake kanggo wektu sing suwe, please store the remote control in a clean and safe place.

6. Avoid moisture and shock during storage and transportation.

1. Pambuka Produk

Handwheel Working Daya Supan Voltase	DC24V / 1A
Voltase penerus listrik	DC24V / 1A
Range Output Dicarasi	DC24V
Dawane kabel rodha tangan	10m
Dawane kabel pungkasan	1m
Panampa jaringan jaringan pungkasan	3m
Suhu operasi	-25℃<X<55℃
Dhuwur Anti-Gugur	1m
Kuantitas Tombol Custom	6
Ukuran Produk	233*90.7*77.4(Mm)

4.Introduksi fungsi produk

Cathetan:

Tombol mandeg darurat:

Pencet tombol mandeg darurat, lan rong set darurat mandhegake outputs ing panrima bakal dipotong, and all functions of the handwheel will be invalid.

Sawise ngeculake mandheg darurat, Output io darurat ing panrima ditutup, and all functions of the handwheel are restored.

② Tampilan layar:

6.2 Ukuran Instalasi Panampa

6.3 Ukuran Instalasi Plugs Aviation

6.4 Diagram referensi wiring wiring panrima
7.Pandhuan operasi produk

1. Nalika panrima wis ana lan lampu petunjuk sing digawe sumunar, Sambungake panrima menyang komputer nganggo kabel jaringan, Setel alamat IP tetep komputer, Lan gunakake piranti lunak alat konfigurasi jaringan kanggo nyetel paramèter jaringan fungsi tangan. Kanggo cara nyetel spesifik, waca ing “Manual pangguna gantung luntun lxwgp-ets”.

2.Sawise panrima wis siyap, Sistem kasebut kudu program program PLC. Mangga deleng ing “LXWGP-ETS Tanduran Alcatel Sistem Kontrol Sistem Sistem Kontrol Sistem Sistem” and PLC program routine materials for details.

3.Sawise ngrampungake setelan ing ndhuwur, njupuk panrima menyang kabinet listrik mesin lan nginstal. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.

4.Sawise ngrampungake setelan ing ndhuwur, njupuk panrima menyang kabinet listrik mesin lan nginstal. Tarik kabel jaringan saka komputer lan pasang ing antarmuka X sistem. Connect the receiver power supply and pulse line.

5. Pilih Pilihan Axis: Switch the axis selection switch and select the axis you want to operate on.

6. Pilih Magnifikasi: Switch the magnification switch and select the magnification level you need.

7. Ngalih sumbu: Pencet terus tombol Aktifake, Pilih switch pilihan AXIS pilihan, Pilih switch pembahagi, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.

8. Pencet terus tombol apa wae kanggo ngaktifake output IO saka tombol sing cocog ing panrima, and release the button to turn off the output.

9. Pencet tombol mandeg darurat, output Io sing cocog karo panampa sing cocog karo panampa bakal dipotong, Fungsi handwheel bakal dipatèni, Rilis tombol mandeg darurat, output io mandheg darurat bakal ditutup, and the handwheel function will be restored.

8.Katrangan Model Produk

9.Njupuk alangan produk

1.Pambuka Produk

2. Fitur fungsi produk

3. Spesifikasi Produk

Tegangan operasi lan arus remot nirkabel	3V/14MA
Spesifikasi baterei	2 baterei AA alkalin, size 5
Rentang weker tegangan rendah remote nirkabel	< 2.3V
Voltase penerus listrik	DC5V-24V/A
Receiver darurat mandeg sawetara beban output	AC125V-1A/DC30V-2A
Receiver mbisakake sawetara beban output	AC125V-1A/DC30V-2A
Rentang beban output tombol khusus panrima	DC24V/50mA
Rentang beban output sumbu panrima	DC24V/50mA
Rentang beban output pembesaran panrima	DC24V/50mA
Daya transmisi terminal genggam	15dBm
Receiver nampa sensitivitas	-100dBm
Frekuensi komunikasi nirkabel	433Pita frekuensi MHz
Jarak komunikasi nirkabel	Jarak bebas alangan saka 40 meter
Suhu operasi	-25℃ < X < 55℃
Dhuwur anti tiba	1 (meter)
Jumlah tombol khusus	2

4. Pengenalan Fungsi Produk

Cathetan:

① Encoder pulsa:
Pencet terus tombol Aktifake, goyangake encoder pulsa, emit sinyal pulsa,and control the movement ofthe machine axis.
② Tombol Aktifake:
Pencet salah siji tombol aktif ing salah siji sisih, lan loro set ngaktifake output IO ing panrima bakal tumindak. Bukak tombol ngaktifake kanggo medhot output ngaktifake IO; Lan sadurunge ngoper magnification pilihan sumbu lan goyang handwheel,tombol ngaktifake kudu dicekel mudhun kanggo dadi efektif; This function can be cancelled through configuration software.

③ Lampu indikator:
Lampu sisih kiwa: daya ing cahya,handwheel nggunakake sumbu kanggo milih OFF kanggo daya ing, lan lampu iki tetep urip sawise daya urip;
Cahya tengah: lampu sinyal sing murup nalika ngoperasikake sembarang fungsi saka handwheel, lan ora murup nalika ora ana operasi;
Lampu sisih tengen: Lampu Lampu Voltase Low, tingkat baterei kurang,lampu iki sumunar utawa tetep urip, battery needs to be replaced.

④ Tombol mandheg darurat:
Pencet tombol mandeg darurat, lan rong set darurat mandhegake outputs ing panrima bakal dipotong, and all functions of the handwheel will be invalid.

⑤ Ngalih pembesaran:
Pencet terus tombol aktifake kanggo ngalih saklar pembesaran, which can switch the magnification controlled by the handwheel.

⑥ Saklar pilihan sumbu (switch daya):
Pencet terus tombol ngaktifake kanggo ngalih saklar pilihan sumbu, kang bisa ngalih sumbu gerakan kontrol dening handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Tombol khusus:
Loro tombol khusus, each corresponding to an IO output point on the receiver.

5. Diagram aksesoris produk

6. Pandhuan instalasi Produk
6.1 Langkah-langkah instalasi Produk

1. Pasang panrima menyang kabinet listrik liwat gesper ing mburi, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Rujuk diagram panrima wiring kita lan mbandhingake karo peralatan ing situs sampeyan. Connect the equipment to the receiver via cables.
3.Sawise panrima wis didandani kanthi bener, Antena sing dilengkapi karo panrima kudu nyambung, lan mburi njaba antena kudu dipasang utawa diselehake ing njaba kabinet listrik. Apike kanggo nyelehake ing ndhuwur kabinet listrik kanggo efek sinyal paling apik. Dilarang ninggalake antena ora disambungake utawa dilebokake ing lemari listrik, as this may result in the signal being unusable.
4. Pungkasane, nguripake saklar daya saka handwheel, and you can operate the machine remotely using the handwheel.

6.2 Ukuran Instalasi Panampa

6.3 Diagram referensi wiring wiring panrima

7. Pandhuan operasi produk
1. Daya ing mesin lan panrima. Lampu indikator kerja panrima sumunar. Pasang baterei ing roda tangan elektronik nirkabel, ngamanake tutup baterei, lan
nguripake saklar daya setir elektronik nirkabel. The handwheel’s battery level indicator light is on.
2. Pilih sumbu koordinat: Pencet terus tombol Aktifake, ngalih saklar pilihan sumbu, and select the axis you want to operate.
3. Pilih Magnifikasi: Pencet terus tombol Aktifake, ngalih saklar pembesaran,and select the desired magnification level.
4. Ngalih sumbu: Pencet terus tombol Aktifake, Pilih switch pilihan AXIS pilihan, Pilih switch pembahagi, banjur muter encoder pulsa. Puter searah jarum jam kanggo mindhah
positive axis and counterclockwise to move the negative axis.
5. Pencet terus tombol apa wae, lan tombol cocog IO output panrima bakal diuripake. Ngeculake tombol, and the output will be turned off.
6. Pencet tombol mandeg darurat, output Io sing cocog karo panampa sing cocog karo panampa bakal dipotong, Fungsi handwheel bakal dipatèni,Rilis tombol mandeg darurat, output io mandheg darurat bakal ditutup, and the handwheel function will be restored.
7. Yen handwheel ora dilakokno sajrone wektu, bakal kanthi otomatis mlebu mode turu kanggo nyuda konsumsi daya. Yen digunakake maneh, the handwheel can be activated by pressing the enable button.
8. Yen tangan tangan ora digunakake kanggo wektu sing suwe, dianjurake kanggo ngalih poros handwheel menyang posisi OFF, mateni kekuwatan tangan, and extend the battery life.

8. Katrangan Model Produk

① :ZTWGP nggambarake gaya tampilan
②：Parameter output pulsa:
01: Nuduhake yen sinyal output pulsa yaiku A, B; Pulsa voltase 5V; pulse quantity 100PPR.
02：Nuduhake yen sinyal output pulsa yaiku A lan B; Tegangan pulsa 12 V; pulse quantity 100PPR.
03：Nuduhake yen sinyal output pulsa yaiku A, B, A -, B -; Pulsa voltase 5V; pulse quantity 100PPR.
04：Nuduhake output sirkuit sing kurang murah, Kanthi sinyal output pulsa saka A lan B;The number of pulses is 100PPR.
05：Nuduhake output sumber PNP sing dhuwur, Kanthi sinyal output pulsa saka A lan B; The number of pulses is 100PPR.
③：Makili nomer saklar pilihan sumbu, 2 nggantosi 2 axes.
④：Nggantosi jinis sinyal switch pilihan sumbu, A nggambarake sinyal output output titik-titik, and B represents encoded output signal.
⑤：Nggantosi jinis sinyal ngalih multiplikasi, A nggambarake sinyal output output titik-titik, and B represents encoded output signal.
⑥：Nggantosi nomer tombol khusus, 2 nggantosi 2 custom buttons.
⑦：Nggantosi sumber daya kanggo handwheel sistem, lan 05 represents 5V power supply.
⑧：L nggantosi kolom kiwa (wadhah piso kiwa), lan R nggantosi kolom tengen (wadhah piso tengen).

9.Solusi kanggo Malfunctions Product

1.Pambuka Produk

Tangan tangan elektronik nirkabel digunakake kanggo tuntunan manual, posisi, Alat Alat,lan operasi liyane ing alat mesin CNC. Produk iki nggunakake teknologi transmeless nirkabel, Ngilangi Sambungan Kabel Musim semi Tradisional, nyuda gagal peralatan sing disebabake kabel, ngilangi cacat kabel seret lan noda minyak, lan nggawe operasi luwih trep. Model handwheel elektronik nirkabel iki minangka handwheel khusus kanggo sistem Fanuc. Koordinat sistem Fanuc ditampilake ing wektu nyata ing layar handwheel liwat protokol IO-LINK, lan pilihan sumbu,Magnifikasi, lan sinyal tombol disambungake langsung menyang sistem liwat protokol IO-LINK, reducing wiring.

2. Fitur Produk
1. Teknologi Komunikasi Wireless Wireless 433MHZ, Jarak Operasi Wireless yaiku 40 meter;
2. Fungsi Frekuensi Hopping Otomatis, Gunakake 32 pesawat saka remot kontrol nirkabel ing wektu sing padha tanpa mengaruhi saben liyane;
3. Dhukungan tombol mandeg darurat, Output Signal Io, disambungake menyang sistem liwat kabel IO;
4. Dhukungan 4 Kancing Custom, Signal IO, sinyal output menyang sistem liwat protokol link;
5. Dhukungan Tombol Gerakan Cepet + lan tombol -, penet terus tombol kanggo ngganti tangan kanggo mindhah mesin;
6. Ndhukung Kontrol 6 Axis, Signal IO, sinyal output menyang sistem liwat protokol link;
7. Dhukungan 1X,10x, 100Kontrol X . Dhukungan switch l0 sinyal, lan output sinyal menyang sistem liwat protokol IO-LINK;
8. Dhukungan ngaktifake fungsi tombol, nyambung menyang sistem liwat kabel IO, lan kontrol encoder aktif ing wektu sing padha;
9. Ndhukung Pulse Encoder, 100 pulsa / bunder, ngakses antarmuka sistem MPG handwheel dening outputting sinyal enkoding AB;

3.Spesifikasi Produk

4.Fitur produk

Cathetan:
①Tombol mandeg darurat:
Pencet tombol mandeg darurat, loro darurat mandeg IO output ing panrima pedhot, lan kabeh fungsi handwheel ora valid.Sawise mandeg darurat dirilis, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Tampilan layar:

③Tombol Kustom:
4 Kancing Custom, saben tombol cocog karo titik output IO ing panrima, disambungake menyang sistem liwat IOLINK. Umume, the ~ button is set as a high-speed button.
④Saklar pilihan sumbu:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Tombol trabasan:
Pencet tombol trabasan "+" kanggo mindhah mesin maju, lan pencet tombol short cut "-" kanggo mindhah mesin negatif. This can replace turning the hand wheel to move the machine.
⑥Tombol Aktifake:
Pencet terus salah siji tombol aktif ing sisih loro lan goyangake encoder pulsa dadi efektif. Lan rong klompok ngaktifake output IO ing panrima diuripake. Release the enable button and the enable IO output is disconnected.
⑦ Ngalih rasio:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Encoder pulsa:
Pencet terus tombol Aktifake lan goyangake encoder pulsa kanggo ngirim pulsa
signal to control the movement of the machine axis.
⑨Saklar daya:
Handwheel power button.

5.Diagram aksesoris produk

6.Pandhuan instalasi Produk

6.1 Langkah-langkah instalasi Produk

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Rujuk diagram kabel panrima kita, Bandhingake karo peralatan ing situs sampeyan, lan nyambung
the equipment to the receiver via cables.
3. Sawise panrima tetep, Antena sing dilengkapi karo panrima kudu nyambung,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
Apike kanggo nyelehake ing ndhuwur kabinet listrik kanggo efek sinyal paling apik. Iku
dilarang ninggalake antena ora disambungake utawa nyelehake antena ing lemari listrik,
which may cause the signal to be unusable.
4.Pungkasane, Nguripake saklar daya tangan lan sampeyan bisa ngoperasikake mesin kasebut
handwheel remote control.

6.2 Ukuran Instalasi Panampa

6.3 Diagram referensi wiring wiring panrima

7. Pangopènan lan perawatan

1. Gunakake ing lingkungan garing kanthi suhu lan tekanan normal kanggo ngluwihi
urip layanan;
2. Aja nggunakake ing lingkungan ora normal kayata udan lan banyu umpluk kanggo ngluwihi
layanan layanan;
3. Mangga njaga tampilan handwheel resik kanggo ngluwihi umur layanan;
4. Aja nganti nyepelekake, Mudhun, nabrak, lsp. kanggo nyegah karusakan ing bagean tliti
nang handwheel utawa nimbulaké kasalahan tliti;
5. Yen ora digunakake kanggo wektu sing suwe, Mangga simpen tangan ing papan sing resik lan aman;
6. Pay attention to moisture and shock during storage and transportation.

8. Informasi Keamanan

1. Mangga maca pandhuan kanthi ati-ati sadurunge digunakake. Ora profesional dilarang
operating.
2. Mangga ngganti baterei ing wektu nalika baterei sithik banget kanggo ngindhari kesalahan sing disebabake
insufficient power causing the handwheel to be unable to operate.
3. Yen ndandani dibutuhake, Hubungi pabrikan. Yen karusakan disebabake didandani dhewe,
the manufacturer will not provide warranty.

1.Pambuka Produk

Tangan tangan elektronik nirkabel digunakake kanggo tuntunan manual, posisi, setting alat lan
Operasi Piranti Mesin CNC. Produk iki nggunakake teknologi transmeless nirkabel,
Ngilangi Sambungan Kabel Musim semi Tradisional, nyuda gagal peralatan sing disebabake kabel,
Ngilangake kekurangan kabel nyeret kabel, Noda minyak, lsp., lan luwih trep kanggo
operate. Iki digunakake digunakake ing alat mesin CNC kayata Pusat Mesin Gantry, Gantry
Lathes vertikal, Mesin Pangolahan Gear Cnc, lan bisa dicocogake karo macem-macem CNC
Sistem ing pasar, Sing Siemens, Mitsubishi, Fanuc, Sistem Syntec lan CNC liyane
brands.

2.Fitur Produk

1. Teknologi Komunikasi Wireless Wireless 433MHZ, Jarak Operasi Wireless yaiku 80 meter;
2. Fungsi Frekuensi Hopping Otomatis, Gunakake 32 Set pangontrol remot nirkabel ing
wektu sing padha tanpa mengaruhi saben liyane;
3. Dhukungan tombol mandeg darurat, lan sawise pasamunan dipateni, mandeg darurat
Tombol isih bener;
4. Dhukungan 6 Kancing Custom, Output Signal Io;
5. Ndhukung Kontrol 6 Axis, 7-12 Kontrol Axis bisa disesuaikan;
6. Ndhukung 1x,10X, 100X kontrol lan bisa dadi maksimal tambahan 1000X;
7. Ndhukung fungsi tombol ngaktifake, ngalih output l0 sianals. Pilihan Axis,maanifikasi
lan ngodhe.;
8. Dhukungan pilihan sumbu lan output encoder pilihan perbesaran;
9. Ndhukung Tipe standar-C, 5Spesifikasi V-2A Ngisi daya, specification baterei dibangun ing
14500/1100mAh.

3.Spesifikasi Produk

4.Introduksi fungsi produk

Cathetan：
①Tombol mandeg darurat：
Nalika tombol mandeg darurat dipencet, loro darurat mandeg IO output ing
panrima wis pedhot, lan kabeh fungsi handwheel ora bener. Nalika darurat
mandeg dirilis, Output io darurat ing panrima ditutup, lan kabeh handwheel
fungsi dibalèkaké; lan sawise pasamunan dipateni, output IO mandheg darurat
of the receiver is still valid when the emergency stop button is pressed.

②Tombol ngaktifake:
Pencet salah siji saka tombol aktif ing loro-lorone, lan rong klompok ngaktifake IO
output ing panrima bakal diuripake. Bukak tombol aktifake lan aktifake IO
output bakal dipateni. Kajaba iku, Sampeyan kudu mencet terus tombol Aktifake sadurunge
Ngalih Rasio Pilihan Axis lan goyangake tangan. Fungsi iki bisa dadi
canceled through the configuration software.
Switch pilihan (switch daya):
Pencet terus tombol Aktifake banjur ngalih switch Axis pilihan kanggo ngalih
mindhah sumbu dikontrol dening tangan. Ngalih ngalih iki menyang sumbu lan
turn on the handwheel power.

④pulse Encoder:
Pencet terus tombol Aktifake lan goyangake encoder pulsa kanggo ngirim pulsa
signal to control the movement of the machine axis.

Indikator ⑤battery:
Tampilan daya wheel tangan, kabeh sing cerah tegese kebak kekuwatan, kabeh tegese ora
diuripake utawa ora duwe kekuwatan, Lampu kothak kiwa pisanan, nuduhake yen kekuwatan banget sithik,
please charge in time.
Lampu Lampu:
Yen cahya sinyal ana ing, Tegese handwheel dioperasekake lan sinyal yaiku
normal; Yen cahya sinyal mati, Tegese ora ana operasi, utawa dioperasikake nanging
the wireless signal is not connected.

5.Diagram aksesoris produk

6.Pandhuan instalasi Produk

6.1 Langkah-langkah instalasi Produk
1. Instal panrima ing kabinet listrik nggunakake klip ing mburi, utawa nginstal ing
the electrical cabinet using the screw holes at the four corners of the receiver.
2.Rujuk diagram kabel panrima kita, Bandhingake karo peralatan ing situs sampeyan, lan nyambung
the equipment to the receiver via cables.
3.Sawise panrima tetep, Antena sing dilengkapi karo panrima kudu nyambung,
lan mburi antena utama kudu diinstal utawa dilebokake ing njaba kabinet listrik. Iku
dianjurake kanggo nyelehake ing ndhuwur kabinet listrik kanggo efek sinyal paling apik. Iku
Dilarang ninggalake antena sing ora dikonfirmasi utawa nyelehake antena ing kabinet listrik,
which may cause the signal to be unusable.
4. Pungkasane, Nguripake saklar daya tangan lan sampeyan bisa ngoperasikake mesin kasebut
handwheel remote control.

6.2 Ukuran Instalasi Panampa

6.3 Diagram referensi wiring wiring panrima

7.Pandhuan operasi produk
1. Mesin kasebut digunakake ing, Panrima wis digunakake ing, Indikasi panrima
lampu kelip-kelip, Handwheel Elektronik Wireless duwe baterei wis diinstal, Tutup baterei
diikat, Switchel daya tangan tangan nirkabel nirkabel diuripake, lan ing
Lampu Daya Handwheel urip;
2. Pilih sumbu koordinat: Pencet terus tombol Aktifake, ngalih pilihan axis
ngalih, banjur pilih sumbu sing pengin digunakake;
3. Pilih Magnifikasi: Pencet terus tombol Aktifake, ngalih switch,
banjur pilih level pembagi sing dibutuhake;
4. Ngalih sumbu: Pencet terus tombol Aktifake, Pilih switch pilihan AXIS pilihan, Pilih
switch magnasi, banjur Rotateleter Encoder Pulsa kanggo muter sumbu obah sing positif
jarum jam lan sumbu obah sing negatif;
5. Pencet terus tombol apa wae, lan tombol sing cocog karo output saka
Panampa bakal diuripake. Rilis tombol kanggo mateni output;
6. Pencet tombol mandeg darurat, output darurat darurat sing cocog karo
panrima ora pedhot, Fungsi handwheel dipatèni, ngeculake mandeg darurat
Tombol, Output io darurat darurat ditutup, lan fungsi handwheel dibalekake;
7. Yen handwheel ora dilakokno sajrone wektu, Bakal ngetik turu kanthi otomatis
Mode kanggo nyuda konsumsi daya. Yen digunakake maneh, Tangan tangan bisa uga
diuripake kanthi mencet tombol Aktifake;
8. Yen tangan tangan ora digunakake kanggo wektu sing suwe,Apike kanggo ngalih handwheel
batang menyang posisi mati, mateni kekuwatan tangan, and extend the battery life.

8.Katrangan Model Produk

① ：DWGP makili gaya penampilan

② ：Parameter output pulsa:
01: Nuduhake yen sinyal output pulsa minangka lan b, lan voltase pulsa yaiku 5v; Pulsa
jumlah 100pr;
02: Nuduhake yen sinyal output pulsa minangka lan b, lan voltase pulsa yaiku 12v; Pulsa
kuantitas 25pr;
03: Nuduhake yen sinyal output pulsa yaiku b、A-、B-； Pulsa voltase 5V; Pulse quantity 1
00Ppr;
04: Nuduhake output sirkuit sing kurang murah, Kanthi sinyal output pulsa saka A lan B; The
Jumlah pulsa yaiku 100ppr;05: Nuduhake output sumber PNP sing dhuwur, sinyal output pulsa
yaiku a lan b; Kuantitas pulsa yaiku 100ppr;
③ : nggantosi nomer pemilihan sumbu, 6 nggantosi 6 sumbu, 7 nggantosi 7 axis.
④ : nggantosi jinis sinyal sumbu sumbu, A nggambarake sinyal output output titik-titik,
B nggambarake sinyal output sing bisa dikodhe;

⑤ : nggantosi jinis sinyal ngalih magnifikasi,
A nggambarake sinyal output output titik-titik, B nggambarake sinyal output sing bisa dikodhe;
⑥ : nggantosi nomer tombol adat, 6 nggantosi 6 Kancing Custom;
⑦ : nggantosi pasokan listrik kanggo handwheel sistem, 05 makili sumber daya 5v,
lan 24 represents 24V power supply.

9.Ngatasi masalah produk

10. Pangopènan lan perawatan

1. Mangga nggunakake ing lingkungan garing ing suhu kamar lan tekanan kanggo ngluwihi layanan;
2. Aja nggunakake ing lingkungan sing ora normal kayata udan lan banyu kanggo ngluwihi layanan layanan kasebut;
3. Mangga tansah munculna tangan tangan ngresiki kanggo njaga uripe;
4. Aja nganti nyepelekake, Mudhun, nabrak, lsp. Kanggo nyegah karusakan ing komponen presisi ing njero
Kesalahan tangan utawa akurasi;
5. Yen ora digunakake kanggo wektu sing suwe, Mangga simpen tangan ing papan sing resik lan aman;
6.Sajrone panyimpenan lan transportasi, attention should be paid to moisture and shock resistance.

11.Informasi safety

1. Mangga maca pandhuan kanthi ati-ati sadurunge digunakake lan nglarang profesional saka operasi;
2. Yen level baterei sithik, Mangga ngisi wektu kanggo ngindhari kesalahan sing disebabake ora cukup
baterei lan kasekengan kanggo ngoperasikake handwheel;

3. Yen ndandani dibutuhake, Hubungi pabrikan. Yen karusakan disebabake perbaikan dhewe, the manufacturer will not provide warranty.

Model：ATWGP-12

Sistem adaptasi: Kabeh sistem CNC kanthi antarmuka tangan

Produk iki minangka generator pulsa manual sing digunakake karo alat mesin CNC. Wis digunakake ing lapangan kayata alat mesin CNC, Cnc lathes, Pusat Mesin,CNC Ukiran lan Milling Mesin. Produk iki nggunakake transmonsechnology nirkabel, Ngilangake kabutuhan sambungan kabel tradisional spring tradisional, Gagal nyuda sing disebabake kabel, Ngilangake Seret Kabel, minyak lan kontaminasi liyane, lan nggawe operasi luwih trep. Paket Produk kalebu tanda tangan lan nirkabel elektronik. Panrima disambungake menyang peralatan CNC liwat kabel jaringan, lan handwheel elektronik (Generator pulsa tangan) disambungake lan komunikasi karo panrima liwat teknologi transmisi nirkabel. Operator nyekel tangan tangan lan bisa nyingkirake alangan sambungan saka kawat musim semi lan mindhah kanthi bebas. Kanggo panggilingan gantri gedhe-gedhe, Cnc lathes, Piranti mesin lelungan, Nglereni lan aplikasi liyane, it brings great convenience and improves work efficiency.

Ndhukung macem-macem merek sistem kayata Siemens, Mitsubishi, Fanuc, Taiwanxindai, Baoyuan, Fagor, Huazhong cnc, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Nggunakake band frekuensi nirkabel 433MHZ, jarak operasi nirkabel yaiku 40 meter;
2. Nganggo fungsi frekuensi frekuensi otomatis kanthi otomatis 32 set handwheels nirkabel ing wektu sing padha tanpa mengaruhi;
3. Ndhukung tombol mandeg darurat lan 3 Output tombol adat;
4. Ndhukung macem-macem pilihan Axis saka 6-Axis, 7-sumbu, 8-sumbu, 9-sumbu, 10-Axis lan 12-Axis, kanthi pilihan 3-kacepetan lan pilihan sing cocog karo 4-kacepetan lan switching ndhukung macem-macem jinis sinyal kayata coding binar, titik-to-point, kode abu-abu, lsp.;
5. Ndhukung sinyal pulsa bedane 5v, 24V Signal Pulsa lan jinis sinyal pulsa liyane;
6. Desain Konsumsi Daya Dhuwur, 2 Baterei AA bisa digunakake luwih saka 1 Wulan;
7. Ndhukung antena ekstensi eksternal, Cocog kanggo macem-macem lingkungan instalasi mesin, njamin stabilitas sinyal;

Cathetan:
1. Lampu Indikator Status:
Lampu Sinyal (kiwa): Cahya sinyal tansah ana nalika tangan tangan digunakake, lan ora entheng nalika ora operasi;
Lampu Lampu Voltase Low (Tengen): Nalika kekuwatan baterei sithik,lampu weker sumunar utawa tetep;
2. Ngaktifake tombol:
Sawise menet terus tombol Aktifake, Pilihan Axis lan sinyal gedhene diuripake, lan output encoder pulsa bener;
3. Tombol Custom:
Tombol tanpa fungsi bisa ngontrol output ngalih sing cocog karo panrima;

Com1: Terkenal umum kanggo output sinyal pilihan sumbu Axis; bisa nyambung karo sinyal umum 0-24v
Com2: Terminal umum saka 3 Output Tombol Custom;

*Pilihan Axis lan Magnifikasi bisa dipilih liwat piranti lunak, coding utawa titik-to-point, Mangga takon karo staf kanggo rincian

The final interpretation right of this product belongs to our company.

1.Pambuka kontrol remot

A.Product comPosition
Koordinate Tampilan Coordinate Tampilan Nirkabel Wektu Elektronik Nirkabel Time, kalebu rong bagean: handwheel elektronik + panrima;

b.characteristik

*6 Tombol Custom bisa ngontrol 6 ngalih output;
*Tampilan layar nampilake registrasi PLC Corpording Cates ing wektu nyata, and supports 6-axis display of real-time coordinates.

2.Lapangan Aplikasi

1) Handwheel elektronik disambungake menyang PLC liwat panrima Ethernet

A.Tandhe tanduk ngirim data kunci kanthi nirkabel menyang panrima, lan panrima nyerat tombol liwat area kabel PC PLC System DB; Panampa maca data sing bakal ditampilake saka wilayah DB sing ditetepake, banjur mulihake data menyang layar tampilan tangan. Pangguna bisa ngatur alamat dhasar maca lan nulis wilayah DB ing tuntunan handwheel, so that the handwheel can read and write the data in the DB area of the PLC.

b. Panrima ndhukung Siemens s7 protokol. Ditrapake kanggo plc s7-200, PLC S7-300 and PLC S7-1200.

c. The user can configure the receiver to server mode and client mode through the PLC connection configuration tool.

Ing mode server, Pangguna ngaturake alamat PLC lan nulis liwat piranti lunak konfigurasi WGP-ETS;Gunakake alat Konfigurasi PLC Confurtrasi kanggo ngatur panrima menyang mode klien. Sawise konfigurasi, the XWGP-ETS receiver can communicate with the PLC through the standard S7 protocol.

2)Aplikasi Khusus

Aplikasi Khusus Panrima Handwheel lan Siemens PLC S7-200:

a. Tombol ing tangan tangan cocog karo nilai area bool sing disetel dening pangguna ing PLC. Yen tombol tangan handwheel dipencet, Wilayah bool sing cocog, lan nalika dibebasake, iku palsu, lan Alamat Dasar Wilayah Bool bisa disetel liwat Handwheel;

b. Handwheel bisa maca nilai area DB ing PLC. Siji sumbu duwe 4 Bytes Data Tampilan, lan 6 Axes duwe total 24 Byte. The base address of the DB area can be set through the WGP-ETS configuration software.

4.Pengenalan Penampilan

5.Definisi terminal lan tabel coding panrima

6.Ukuran tampilan

Sistem adaptasi: Kabeh sistem CNC kanthi antarmuka tangan

Produk iki minangka generator pulsa manual sing digunakake karo alat mesin CNC. Wis digunakake ing lapangan kayata alat mesin CNC, Cnc lathes, Pusat Mesin,CNC Ukiran lan Milling Mesin. Produk iki nggunakake transmonsechnology nirkabel, Ngilangake kabutuhan sambungan kabel tradisional spring tradisional, Gagal nyuda sing disebabake kabel, Ngilangake Seret Kabel, minyak lan kontaminasi liyane, lan nggawe operasi luwih trep. Paket Produk kalebu tanda tangan lan nirkabel elektronik. Panrima disambungake menyang peralatan CNC liwat kabel jaringan, lan handwheel elektronik (Generator pulsa tangan) disambungake lan komunikasi karo panrima liwat teknologi transmisi nirkabel. Operator nyekel tangan tangan lan bisa nyingkirake alangan sambungan saka kawat musim semi lan mindhah kanthi bebas. Kanggo panggilingan gantri gedhe-gedhe, Cnc lathes, Piranti mesin lelungan, Nglereni lan aplikasi liyane, it brings great convenience and improves work efficiency.

Ndhukung macem-macem merek sistem kayata Siemens, Mitsubishi, Fanuc, Taiwanxindai, Baoyuan, Fagor, Huazhong cnc, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Nggunakake band frekuensi nirkabel 433MHZ, jarak operasi nirkabel yaiku 40 meter;
2. Nganggo fungsi frekuensi frekuensi otomatis kanthi otomatis 32 set handwheels nirkabel ing wektu sing padha tanpa mengaruhi;
3. Ndhukung tombol mandeg darurat lan 3 Output tombol adat;
4. Ndhukung macem-macem pilihan Axis saka 6-Axis, 7-sumbu, 8-sumbu, 9-sumbu, 10-Axis lan 12-Axis, kanthi pilihan 3-kacepetan lan pilihan sing cocog karo 4-kacepetan lan switching ndhukung macem-macem jinis sinyal kayata coding binar, titik-to-point, kode abu-abu, lsp.;
5. Ndhukung sinyal pulsa bedane 5v, 24V Signal Pulsa lan jinis sinyal pulsa liyane;
6. Desain Konsumsi Daya Dhuwur, 2 Baterei AA bisa digunakake luwih saka 1 Wulan;
7. Ndhukung antena ekstensi eksternal, Cocog kanggo macem-macem lingkungan instalasi mesin, njamin stabilitas sinyal;

Cathetan:
1. Lampu Indikator Status:
Lampu Sinyal (kiwa): Cahya sinyal tansah ana nalika tangan tangan digunakake, lan ora entheng nalika ora operasi;
Lampu Lampu Voltase Low (Tengen): Nalika kekuwatan baterei sithik,lampu weker sumunar utawa tetep;
2. Ngaktifake tombol:
Sawise menet terus tombol Aktifake, Pilihan Axis lan sinyal gedhene diuripake, lan output encoder pulsa bener;
3. Tombol Custom:
Tombol tanpa fungsi bisa ngontrol output ngalih sing cocog karo panrima;

Com1: Terkenal umum kanggo output sinyal pilihan sumbu Axis; bisa nyambung karo sinyal umum 0-24v
Com2: Terminal umum saka 3 Output Tombol Custom;

*Pilihan Axis lan Magnifikasi bisa dipilih liwat piranti lunak, coding utawa titik-to-point, Mangga takon karo staf kanggo rincian

The final interpretation right of this product belongs to our company.