와이어 톱 기계 자동 절단 무선 원격 제어 DH12S-P6S

설명

1.제품 모델

 

모델: DH12S-P6S

해당 장비:wire saw/blade saw machine

2.제품 액세서리 다이어그램

메모: 세 가지 안테나 중 하나를 선택할 수 있습니다. 흡입 컵 안테나는 기본적으로 표준입니다.

3.원격 제어 스위치 설명

4.DisplayContent 소개

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(매개 변수 조정 가능)
Automatic cutting main motor setting current: Setting: 28 (매개 변수 조정 가능)
Swing arm motor speed: Swing: 0-50

저전압: 원격 제어 배터리가 너무 낮습니다, 배터리를 교체하십시오.

네트워크가 떨어졌습니다: 무선 신호가 중단됩니다. 수신기의 전력을 확인하십시오, 다시 전원을 켜십시오, 리모컨을 다시 시작하십시오.

5.원격 제어 기능 작동 지침

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, 전원 스위치를 켭니다, and the display will show the motor speed, 성공적인 시작을 나타냅니다.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, 회전하십시오 “전방/반대” 전달로 전환하십시오, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, 회전하십시오 “전방/반대” 반전으로 전환하십시오, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;회전하십시오 “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, 회전하십시오 “전방/반대” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

회전하십시오 “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” 스위치, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

눌렀다 “speed adjustment enable” 버튼을 돌리고 회전합니다 “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “전방/반대” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (사용자는 허가없이 수정할 수 없습니다)

Enter the parameter menu:수동 모드에서, when the main motor speed is 0, 전방/리버스 스위치를 연속으로 세 번 밀어 넣습니다., and then push it down three times in a row to enterthe parameter menu;
매개 변수 메뉴를 종료하십시오: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, 기본 800, unit milli second,수정은 금지됩니다;
감속 매개 변수: 절단 전류 변화 값 이이 값을 초과 할 때, rapid deceleration begins, unit Ampere;
가속도 A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
감속 a2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, 수정은 금지됩니다;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, 수정은 금지됩니다;
최대 전류: The range of main motor feedback current, unit Ampere;
최대 호스트: Remote control main motor speed adjustment display range;
최대 걷기: Invalid parameter;
속도 제한 오프셋: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: 자동 절단, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;단위: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.원격 제어 전기 특성

7.원격 제어 크기

이 제품의 최종 해석은 우리 회사에만 해당됩니다..