2. Produkto savybės
1. Priimkite 433MHz belaidžio ryšio technologiją, Belaidžio veikimo atstumas yra 100 meters.
2. Priimkite automatinio dažnio šuolio funkciją, naudoti 32 belaidžių nuotolinio valdymo pultelių rinkiniai vienu metu, without affecting each other.
3. Palaikykite visus keitiklius su 485-Modbus RTU protokolu. Inverterių prekės ženklai buvo pritaikyti, įskaitant:Šanchajus Xielinas, Fuji, Inovacijos, Zhongchen, INVT, Ančuanda. If the brand is not ada please contact us for customization.
4. Palaikykite didelio variklio keitiklio paleidimą, greičio reguliavimas, and current reading.
5. Palaikykite kairiojo ir dešiniojo vikšrinio keitiklio greičio reguliavimą, pradėti, front and back left and right control.
6. Support left and right crawler inverter straight line correction to keep the machine moving in a straight line.
7. Atraminio lyno pjūklo automatinio pjovimo funkcija, automatically adjust the left and right crawler speed in real time according to the large motor current information.
8. Tuo pačiu metu, jis suderinamas su tiesioginiu IO išėjimu, kad būtų galima valdyti variklio paleidimą ir sustabdymą, and analog voltage output to control the motor speed.

3. Produkto specifikacijos

4. Produkto funkcijos įvadas

Pastabos:
①Screen display:

②Mode switch:
Using a 2-level switch, it is possible to switch between automatic and manual modes, and the corresponding mode will be displayed on the screen for switching.
③ Enable:
Combination buttons, some operations require holding down the enable button for operation, please refer to the instructions for each switch for details.
④ Large motor switch:
Using a 3-speed reset switch, pulling this switch can control the forward and reverse rotation of the large motor. Išleidus, the state will remain, and there will be corresponding displays on the screen. The t arrow indicates forward rotation, and the y arrow indicates reverse rotation.
⑤Small motor forward/reverse switch:
Using a 3-speed self-locking switch, pulling this switch can control the small motor to move forward and backward. The corresponding display will show on the screen, with the t arrow indicating forward and the ↓ arrow indicating backward.
⑥Remote control power switch:
The remote control display screen is turned on.
⑦ small motor turning switch:
Using a 3-speed reset switch, when manually operated, the small motor can be controlled to turn left or right. Once released, the remote control will automatically stop this action.When in the forward state, turn this switch and the corresponding display will appear on the screen.The + arrow indicates left turn, and the – arrow indicates right turn.When in reverse mode, turn this switch and the corresponding display will appear on the screen.The + arrow indicates left turn, and the – arrow indicates right turn.Press and hold the enable button, then turn this switch to perform a stationary turning function, making the turn faster.
⑧ Large motor speed regulation:
Using a multi turn encoder knob, rotate the knob to adjust the speed S1 of the large motor For every 1 grid rotation, the speed value of the large motor changes by approximately 0.2 units, and rapid rotation can quickly modify the speed value of the large motor.
9 Small motor speed regulation (linear correction):To use the multi turn encoder knob, in manual mode, for every 1 turn of the knob, the speed value of the small motor changes by approximately 0.1 units. Fast rotation can quickly modify the speed value of the small motor.
Automatiniu režimu, press the enable button and rotate 1 grid each time. The speed limit value F of the small motor changes by approximately 0.1 units. Rapid rotation can quickly modify the speed limit value of the small motor.Press the enable button, turn the knob to the right, and the straight line correction display shows D f: kairėje. Each rotation of the knob increases by 1 unit; Turn left knob, straight line correction display: Df: Teisingai. Each rotation of the knob increases by 1 unit, and each correction unit corresponds to a motor speed control AVI voltage of about 0.02 V.

5. Gaminio priedų schema

6. Produkto diegimo vadovas
6.1 Product Installation Steps
1. Install the receiver in the electrical cabinet through the buckle on the back, or install it in the electrical cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram, compare your on-site equipment, and connect the equipment to the receiver through wires.
3. After the receiver is fixed, the antenna equipped with the receiver must be connected, and the outer end of the antenna must be installed or placed outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for the best signal effect. It is forbidden to leave the antenna unconnected or place the antenna inside the electrical cabinet, which may cause poor signal and unusable.
4. Finally, install the battery in the remote control, tighten the battery cover, and then turn on the power switch of the remote control. After the remote control display shows the normal working interface, you can perform remote control operation.

6.2 Imtuvo montavimo matmenys

6.3 Imtuvo laidų atskaitos schema

7. Product operation instructions
7.1 Remote Control Parameter Settings
How to enter the background parameters of the remote controller: turn the mode switch to manual mode, adjust the speed of the small motor to 25, arba 0, 10, 20, 40, 50, and turn the forward switch of the large motor upwards 3 times and downwards 3 times;
Use the “Small Motor Speed Control” knob to turn the page, press Enable and turn the small motor speed control knob to modify the parameters; after modification, turn the page to the end, select Save and Exit, and press the Enable button to exit the menu;

The parameters are as follows:Maksimali srovė: large motor current feedback value range, setting range 15-200A, Numatytasis 60;

Greičio valdymo parametrai: automatic mode small motor automatic acceleration speed, the smaller the faster, setting range 200-1500, Numatytasis 1000;

Lėtėjimo parametras: Set the upper limit of the motor speed change allowed. When the current changes beyond this value, it will decelerate. The smaller it is, the faster the left and right motors will decelerate. The range is 05-12, and the default is 06;

Pagreitis A1: The larger the value, the faster the motor speed increases, range 00-06,default 01; Lėtėjimas A2: The larger the value, the faster the motor speed decreases, range 00-06, Numatytasis 02;

Enable speed regulation: Whether the small motor speed regulation needs to be enabled, 00 is not enabled, 01 is enabled, Numatytasis 01;

Startup self-locking: Whether the large motor will automatically keep self-locking after the forward and reverse switch is released, 00 is not maintained, 01 is maintained, Numatytasis 01;

Maximum travel: Maximum speed of the left and right motors, range 10-100, Numatytasis 50;

Pjaustymo srovė: Maximum cutting current, the screen displays IC value, range 15-160, Numatytasis 30, the screen displays IC: 30. The upper limit of this parameter = maximum current x 80%;

Numatytasis greičio apribojimas: The default small motor automatic cutting speed at startup, range 00-100, Numatytasis 10, the screen displays F1.0, this parameter is only accurate when the maximum travel is set to 50.

Wireless channel: Default is 10. When the remote control signal is unstable or there is signal interference on site, you can modify this parameter to switch channels to avoid interference;

Greičio apribojimo poslinkis: The upper limit of the automatic cutting speed of the small motor,range 00-200, Numatytasis 60, the screen displays 6.0; Display value upper limit = speed limit offset × 0.1;

Maksimalus šeimininkas: The maximum speed of the large motor, range 10-100, Numatytasis 50;

Mbus device ( mandatory ): large motor inverter model selection, range 00-03, Numatytasis 03;

00- Šanchajus Xielinas 01 Fuji
02- INVT 03 Inovance（Zhongchen, Robicon）

SBUS equipment (mandatory): Small motor frequency converter model selection, range 00-05, Numatytasis 03;
00- Šanchajus Xielinas 01 Fuji
02- INVT 03 Inovance（Zhongchen, Robicon）
04-Anchuanda 05-None

8. Product troubleshooting

7.2 Parameter setting of frequency converter
1. Command source selection: Communication command channel
2. Main frequency source selection: communication given
3. Baud rate: 19200
4. Data format: No verification, data format<8-N-1>
5. Local address: Set the left frequency converter to 1, the right frequency converter to 2, and the large motor frequency converter to 3

7.3 Remote Control Operation Instructions
1. Power on the machine, turn on the remote control, enter the remote control background, set the remote control background parameters, mainlyIt is to set the models of small and large motor frequency converters (skip this step if the machine manufacturer has already set them);
2. Set the parameters of the frequency converter (skip this step if the machine manufacturer has already set it);
3. Set the remote control to manual mode, and then use the remote control to move the machine to the working position;
4. Rankiniu režimu, set the IC value for the cutting current of the large motor and the speed of the large motor;
5. Switch to automatic mode and set the cutting speed limit F value for the small motor;
6. Automatiniu režimu, turn the large motor switch to forward to start the large motor, and then turn the small motor switch to forward or reverse. The remote control enters automatic cutting mode and begins cutting.

9.Priežiūra
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the battery compartment and metal shrapnel area clean.
4. Please avoid damaging the remote control due to squeezing and falling.
5. Jei ilgai nenaudojamas, please remove the battery and store the remote control and battery in a clean and safe place.
6.During storage and transportation, attention should be paid to moisture and shock resistance.

10. Informacija apie saugą
1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery is too low to avoid errors caused by insufficient power, which may result in the remote control being unable to operate.
3. Jei reikia remonto, Kreipkitės į gamintoją. Jei žala atsirado dėl savarankiško remonto, Gamintojas nepateiks garantijos

The remote control for automatic cutting of track car rope saw is suitable for track type rope saw
cutting machines. It uses the 485 Modbus RTU protocol to control the left and right track frequency
converters, as well as the large motor frequency conversion speed control start and the front, rear,
left and right direction controllers. And it can read the working current of the large motor frequency
converter through the 485 Modbus RTU protocol. By analyzing and comparing the current of the
large motor, the speed of the left and right tracks can be automatically adjusted in real time to
achieve automatic cutting function.

2. Produkto funkcinės savybės

1. Adopting 433MHz wireless communication technology, with a wireless operating distance of 100 meters.
2. Priimkite automatinio dažnio šuolio funkciją ir naudojimą 32 sets of wireless remote controllers
simultaneously, without affecting each other.
3. Supports all frequency converters with 485 Modbus RTU protocol, and currently compatible frequency
converter brands include:Šanchajus Xielinas, Fuji, Huichuan, Zhongchen, INVT, ir . For brands
that are not compatible, please contact us for customization.
4. Palaikymo greičio reguliavimas, pradžia, and current reading of large motor frequency converters.
5. Palaikymo kairės ir dešinės takelių dažnio keitiklio greičio reguliavimas, pradžia, priekis, atgal, left and right control.
6. Palaikykite kairiojo ir dešiniojo bėgių kelio dažnio keitiklių tiesinę korekciją, kad mašina vaikščiotų a
straight line.
7. Support automatic cutting function of rope saw, automatically adjust the left and right track speed in
real time according to the current information of the large motor.
8. It is also compatible with direct IO output control for motor start and stop, and analog voltage output
control for motor speed.

3. Produkto specifikacijos

4. Product Function Introduction

Pastabos:
①Screen display:

②Mode switch:

③Enable:
Combination buttons, some operations require holding down the enable button for operation,see the instructions for each switch for details.
④Large motor switch:
Using a 3-speed reset switch, pulling this switch can control the forward and reverse rotation of the large motor. Išleidus, the state will remain, and there will be corresponding displays on the screen. The S1↑ arrow indicates forward rotation, and the S1 ↓ arrow indicates everse rotation.
⑤Small motor forward/reverse switch:
The small motor is equipped with a 3-speed self-locking switch in front of it. Pressing the enable button and pulling this switch can control the small motor to move forward and backward, and the corresponding display will appear on the screen.The ↑↑ arrow represents forward, and the ↓↓ arrow represents backward.
⑥ Straight line correction:
Using a multi turn encoder knob, press the enable button, turn the knob right, and display the straight line correction: Df: The left turn knob increases by 1 unit per rotation, and the left
motor speed increases by 0.1 unit; Turn left knob, straight line correction display: Df: On the right, every turn of the knob increases by 1 unit, and the speed of the right motor increases
by 0.1 unit.
⑦Small motor turning switch:
Using a 3-speed reset switch, when manually operated, the small motor can be controlled to turn left or right. Once released, the remote control will automatically stop this action. In the forward state, when this switch is turned, the corresponding display will appear on the screen. The ←↑ arrow indicates left turn, and the ↑→ arrow indicates right turn.When in reverse mode, turn this switch and the corresponding display will appear on the screen. The ←↓ arrow indicates left turn, and the ↓→ arrow indicates right turn.
⑧ Large motor speed regulation:
Using a multi turn encoder knob, rotating 1 grid each time, the speed value of the large motor changes by approximately 0.2 units. Fast rotation can quickly modify the speed value of the large motor.
⑨ Small motor speed regulation:
Using a multi turn encoder knob, in manual mode, press the enable button and then rotate one grid at a time，the speed value of the left and right small motors changes by about 0.1 units, and quick rotation can quickly modify the speed value of the small motor.In automatic mode, press the enable button and rotate one grid at a time,the speed limit value F of the small motor changes by approximately 0.1 units. Rapid rotation can quickly modify the speed limit value of the small motor.
⑩ Remote control power switch
The remote control display screen is turned on.

5. Gaminio priedų schema

6. Produkto diegimo vadovas
6.1 Produkto montavimo žingsniai
1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Peržiūrėkite mūsų imtuvo laidų schemą ir palyginkite ją su savo vietoje esančia įranga. Connect the equipment to the receiver through wires.
3. Sutvarkius imtuvą, it is necessary to connect the antenna equipped with the receiver and install or place the outer end of the antenna outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for the best signal effect. It is forbidden to leave the antenna unconnected or place it inside the electrical cabinet, as it may cause the signal to be unusable.
4. Finally, install the battery on the remote control, tighten the battery cover, and turn on the power switch of the remote control. After the remote control display screen shows the normal
working interface, remote control operations can be performed.

6.2 Imtuvo montavimo matmenys

6.3 Imtuvo laidų atskaitos schema

7. Product operation instructions
7.1 Remote Control Parameter Settings
Method to enter the remote control backend parameters:

Turn the mode switch to manual mode, adjust the speed of the small motor to 25 on both sides, arba 0, 10, 20, 40, 50 on all sides, and continuously turn the forward switch of the large motor up 3 times and down 3 times;
Use the “Small Motor Speed Control” knob to flip pages, press the enable button, and then turn the small motor speed control knob to modify parameters. After modification, turn the page to the end,select “Save” to exit, and press the enable button to exit the menu;
The parameters are as follows:
Maksimali srovė: feedback range of large motor current, set range 15-200A, Numatytasis 100;
Greičio valdymo parametrai: Automatinis režimas, small motor automatically accelerates faster or slower,the smaller the faster, set range 200-1500, Numatytasis 800;
Lėtėjimo parametras: Set the upper limit that allows the motor speed to change. When the current changes beyond this value, the deceleration will occur. The smaller, the faster the deceleration of the left and right motors, with a range of 05-12 and a default of 06;
Pagreitis A1: The larger the motor speed, the faster it increases, with a range of 00-06 and a default of 01;
Lėtėjimas A2: The larger the motor speed, the faster it decreases, with a range of 00-06 and a default of 02;
Enable speed regulation: Does the small motor speed regulation need to be enabled? 00 does not enable, 01 enables, default is 01;
Pradėkite užsiblokuoti: Does the large motor automatically maintain self-locking after the forward and reverse switches are released? 00 does not hold, 01 holds, default 01
Maksimalus vaikščiojimas: maximum speed of left and right motors, range 10-100, Numatytasis 50;
Pjaustymo srovė: maximum cutting current, displayed on the screen as IC value, range 15-160, default 30,
corresponding to IC: 30 displayed on the screen. The upper limit of this parameter is 80% of the maximum current;
Numatytasis greičio apribojimas: The default small motor automatic cutting speed when turned on is within the range of 0-100, with a default of 10. The screen displays F1.0, and this parameter is only accurate when the maximum walking is set to 50.
Automatinis režimas: Set to 00, the automatic/manual switch is a mode switch. Set to 01, the automatic/manual switch is set to the automatic position, the display screen shows lighting, and the automatic terminal output on the receiver is closed. When set to manual, the automatic output terminal is disconnected;
Speed limit deviation: The upper limit of the automatic cutting speed of the small motor ranges from 00 į 200, with a default of 60 and a corresponding display of 6.0 on the screen; Upper limit of display value=speed limit offset x 0.1;
Maksimalus šeimininkas: maximum speed of the large motor, range 10-100, Numatytasis 50;
Mbus equipment (mandatory): Selection of large motor frequency converter model, range 00-03, Numatytasis 03;
00- Shanghai Xielin 01-Fuji
02-INVT 03-Inovance（Zhongchen, Robicon）
SBUS equipment (mandatory): Small motor frequency converter model selection, range 00-05, Numatytasis 03;

00- Shanghai Xielin 01-Fuji
02-INVT 03-Inovance（Zhongchen, Robicon）

04-Anchuanda 05-None

7.2 Parameter setting of frequency converter
1. Command source selection: Communication command channel
2. Main frequency source selection: communication given
3. Baud rate: 19200
4. Data format: No verification, data format<8-N-1>
5. Local address: Set the left frequency converter to 1, the right frequency converter to 2, ir
the large motor frequency converter to 3
7.3 Remote Control Operation Instructions
1. Power on the machine, turn on the remote control, enter the remote control backend, set the
remote control backend parameters, mainly setting the small motor and large motor frequency
converter models: (skip this step if the machine manufacturer has already set it);
2. Set the parameters of the frequency converter (skip this step if the machine manufacturer
has already set it);
3. Set the remote control to manual mode, and then use the remote control to move the machine to
the working position;
4. Rankiniu režimu, set the cutting current of the large motor to IC and the speed of the large motor
5. Switch to automatic mode and set the cutting speed limit F value for the small motor;
6. Automatiniu režimu, turn the large motor switch to forward to start the large motor, then turn
the small motor switch to forward or reverse, and the remote control enters automatic cutting
mode to start cutting.

8.Product troubleshooting

9.Priežiūra
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the battery compartment and metal shrapnel area clean.
4. Please avoid damaging the remote control due to squeezing and falling.
5. Jei ilgai nenaudojamas, please remove the battery and store the remote control and battery in a clean
and safe place.
6.During storage and transportation, attention should be paid to moisture and shock resistance.

10. Informacija apie saugą
1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery is too low to avoid errors caused by
insufficient power, which may result in the remote control being unable to operate.
3. Jei reikia remonto, Kreipkitės į gamintoją. Jei žala atsirado dėl savarankiško remonto, the manufacturer
will not provide warranty.

Modelis: DH01R-4W-26K

Taikoma įranga:various industrial equipment

2.Produktų priedų schema

PASTABA: Galite pasirinkti vieną iš trijų antenų. The suction cup antenna is standard by default.

3.Product model description

PASTABA:
① DH01R series, if the suffix contains T, it means with emergency stop output;without T, it means without emergency stop output.

②If there is no analog output, there is no need to remark 0W or 0R; the analogquantities W1, W2, W3, and W4 default to 0-10V analog voltage output; at the same time, W1 and W2 can be expanded to 2 isolated digital potentiometer outputs, with a range of 0 -5K ohms, ½ watt; resolution: 20 ohms. The two digital potentials can be used to control the welding current and welding voltage of the welding machine. If the digital potentiometer output is required, user notes are required.

④Analog input, ranging from 1 į 2, indicating that there are 1 į 2 analoginiai įėjimai(maximum 2 kanalai); when there is an analog input, you need to note the voltage range of the analog input (our receiver defaults to 0 -5V, the user can also note as 4-20 mA or 0-10V, kt.) and the corresponding display range of the analog quantity (for example: display 0-100 volts or 0-1000 amps)

These two analog quantities can be used as displays for welding current and welding voltage.

4.Savybės

1）Maximum 26 Relės išėjimai;
2）Maximum 4 Analoginės 0–10 V išėjimo kanalai (Ekrano diapazoną galima pritaikyti): atramos 2 Išplėstinio izoliuoto skaitmeninio potenciometro išvesties kanalai;
3）2 analog inputs; ir rodomas nuotolinio valdymo pulte, Ekrano asortimentą galima pritaikyti
4）1 channels of emergency stop relay output normally closed contacts;
5） Powered by 3 AA baterijos, low power consumption design;
6） Wireless operation distance is 200 metrai;
7）Protection grade IP67;
8）With cross switch operation, supports two 4-direction cross switches;
9）Back strap design.

5.Nuotolinio valdymo jungiklio aprašymas

6.Display content introduction

W1 knob value: W1: 0-1000 (parameter adjustable 0-9999)
W2 knob value: W2: 0-5000 (parameter adjustable 0-9999)
W3 knob value: W3: 0-5000 (parameter adjustable 0-9999)
W4 knob value: W4: 0-5000 (parameter adjustable 0-9999)
ADC1 feedback display: 0-1000 (parameter adjustable 0-5000)
ADC2 feedback display: 0-1000 (parameter adjustable 0-5000)

Žema įtampa: Nuotolinio valdymo akumuliatorius yra per mažas, please replace the battery.

Tinklas krito: Belaidžio ryšio signalas nutraukiamas. Patikrinkite imtuvo galią, vėl įjunkite, and restart the remote control.

7.Nuotolinio valdymo funkcijos veikimo instrukcijos

1） Turn on the remote control
When the receiver is powered on, the receiver working indicator flashes; install two AA batteries in the remote control, Įjunkite maitinimo jungiklį, and the display shows a value,Nurodant sėkmingą paleidimą. The receiver working indicator light becomes solid.
2）Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3）W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4） Emergency stop function
When the emergency stop button is pressed, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5）Parameter menu (users are prohibited from modifying it privately)
Kai kurias nuotolinio valdymo funkcijas galima sureguliuoti per parametrus. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A and K9-B key to page through the menu and select parameters; hold down K1-A, and then press the K9-A/B button to modify parameters;
Išeik iš parametrų meniu: Pasirinkite išsaugoti arba neišsaugoti, and then press the K1-A button to confirm the exit;
F1W1 range: The display range value of the W1 knob on the display screen, adjustable from 0 į 9999;
F2W2 range: The display range value of the W2 knob on the display screen, adjustable from 0 į 9999;
F3W3 range: The display range value of the W3 knob on the display screen, adjustable from 0 į 9999;
F4W4 range: The display range value of the W4 knob on the display screen, adjustable from 0 to 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;

8.Nuotolinio valdymo elektros charakteristikos

9.Nuotolinio valdymo dydis

The final interpretation right of this product belongs only to our company.

Modelis: DH12S-P6S

Taikoma įranga:wire saw/blade saw machine

2.Produktų priedų schema

PASTABA: Galite pasirinkti vieną iš trijų antenų. The suction cup antenna is standard by default.

3.Nuotolinio valdymo jungiklio aprašymas

4.„DisplayContent“ įvadas

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(Parametrai reguliuojami)
Automatic cutting main motor setting current: Setting: 28 (Parametrai reguliuojami)
Swing arm motor speed: Swing: 0-50

Žema įtampa: Nuotolinio valdymo akumuliatorius yra per mažas, please replace the battery.

Tinklas krito: Belaidžio ryšio signalas nutraukiamas. Patikrinkite imtuvo galią, vėl įjunkite, and restart the remote control.

5.Nuotolinio valdymo funkcijos veikimo instrukcijos

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, Įjunkite maitinimo jungiklį, and the display will show the motor speed, indicating successful startup.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, Pasukite “Pirmyn/atvirkštinė” Perjunkite į priekį, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, Pasukite “Pirmyn/atvirkštinė” Perjunkite į atvirkštinę, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Pasukti “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, Pasukite “Pirmyn/atvirkštinė” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Pasukite “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Paspauskite ir palaikykite “speed adjustment enable” mygtukas ir pasukite “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “Pirmyn/atvirkštinė” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (Vartotojams draudžiama jį modifikuoti be leidimo)

Enter the parameter menu:Rankiniu režimu, when the main motor speed is 0, Tris kartus iš eilės pastumkite į priekį/atvirkštinį jungiklį aukštyn, and then push it down three times in a row to enterthe parameter menu;
Išeik iš parametrų meniu: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, Numatytasis 800, unit milli second,Modifikacija draudžiama;
Lėtėjimo parametras: Kai pjovimo srovės pokyčio vertė viršija šią vertę, rapid deceleration begins, unit Ampere;
Pagreitis A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Lėtėjimas A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, Modifikacija draudžiama;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, Modifikacija draudžiama;
Maksimali srovė: The range of main motor feedback current, unit Ampere;
Maksimalus šeimininkas: Remote control main motor speed adjustment display range;
Maksimalus vaikščiojimas: Invalid parameter;
Greičio apribojimo poslinkis: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automatinis pjovimas, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Nuotolinio valdymo elektros charakteristikos

7.Nuotolinio valdymo dydis

The final interpretation right of this product belongs only to our company.

Modelis: DH12S-LD

Taikoma įranga:„Crawler Wire Saw Machine“

Produktų priedų schema

PASTABA: Galite pasirinkti vieną iš trijų antenų. The suction cup antenna is standard by default.

Nuotolinio valdymo jungiklio aprašymas

„DisplayContent“ įvadas

Didelis variklio greitis：S1：0-50
Mažas variklio greitis: S2: 0-50
Maksimalusspeedlimitofautomatinis pjaustymo kumštelinis kumštelis:F:0-30(ParameterSAtleSlable)
Automatinis pjovimo maksimali srovė: IC: 0-35 (Parametrai reguliuojami)
Linijinė pataisos vertė: Df: -99-99 (1 Vienetas yra apie 0,02 V)

Žema įtampa: Nuotolinio valdymo akumuliatorius yra per mažas, please replace the battery.

Tinklas krito: Belaidžio ryšio signalas nutraukiamas. Patikrinkite imtuvo galią, vėl įjunkite, and restart the remote control.

Nuotolinio valdymo funkcijos veikimo instrukcijos

1.Įjunkite nuotolinio valdymo pultą

Kai įjungtas, RF vadovaujama imtuvo lemputė pradeda mirksėti;Įdiekite dvi AA baterijas „ThreCeiver E“ nuotolinio valdymo pulte, Įjunkite maitinimo jungiklį, ir ekrane bus rodomas variklio greitis, indicating successful startup.

2.Didelis variklio ir greičio reguliavimas

Pasukite “Pirmyn/atvirkštinė” Perjunkite į priekį, Didelis imtuvo variklis įsijungs, Ir ekranas bus rodomas pirmyn

Pasukite “Pirmyn/atvirkštinė” Perjunkite į atvirkštinę, Didelis imtuvo variklis įsijungs atvirkščiai, Ir ekranas bus rodomas atvirkščiai

Pasukti “Didelis variklio greičio reguliavimas” rankenėlė Norėdami sureguliuoti imtuvo didelį variklio greičio reguliavimo išėjimo įtampą 0-10 V;

3.Mažas variklio ir greičio reguliavimas

Perkelti “Pirmyn/atvirkštinė” Perjunkite į priekį, Įjungtas kairysis ratas į priekį ir dešinysis ratas į priekį, Ir ekranas rodo į priekį

Pasukite “Pirmyn/atvirkštinė” Perjunkite į atvirkštinę, Įjungtas kairiojo rato atvirkštinis ir dešinys, Ir ekranas rodomas atvirkščiai

4.Pasukite kairėn ir dešinėn

Pasukite “Kairėn/dešinė” Perjunkite į kairę, Imtuvo dešinysis ratas į priekį ir įjungs,Ir ekranas bus rodomas kairėje

Pasukite “Pasukite į kairę/į dešinę” perjungti į dešinę, kairiajame imtuvo ratu, Ir ekranas parodys posūkį į dešinę

5.Pasukite į vietą

Rankiniu režimu:
Pasukti į kairę: Paspauskite ir palaikykite “Įgalinti” mygtukas, Pasukite “Kairysis/dešinysis posūkis” Perjunkite į kairę, Įjungtas kairysis ratas atgal ir dešinysis ratas į priekį nuo imtuvo,Ir pradėkite pasukti į kairę vietoje;

Pasukti į dešinę: Paspauskite ir palaikykite “Įgalinti” mygtukas, Pasukite “Kairysis/dešinysis posūkis” Perjunkite į dešinę, Įjungtas kairysis ratas į priekį ir dešinys, Ir imtuvas pradeda pasisukti į dešinę vietoje;

6.Mažas variklio greičio apribojimo reguliavimas

Automatiniu režimu: Paspauskite ir palaikykite “Įgalinti” mygtukas ir pasukite “Mažas variklio greičio reguliavimas” Norėdami sureguliuoti maksimalų mažo variklio greitį automatinio pjovimo metu;

7.Automatinis pjovimas

Pirmasis žingsnis yra paleisti didįjį variklį; Antras žingsnis yra perjungti režimo jungiklį į “Automatinis”; Trečiasis žingsnis yra paleisti mažą variklį, o ekranas bus rodomas “Auto pjovimas”,nurodant, kad jis įvedė automatinį pjovimo režimą;

8. Tiesios linijos pataisa

Kai kairės ir dešinės vaikščiojimo varikliai juda į priekį ir atgal, kairysis ir dešinysis greitis yra nenuoseklus, Ir tiesus linijinis vaikščiojimas nukrypsta. Norėdami tiksliai sureguliuoti kairiojo ir dešiniojo ratų greitį, galite naudoti nuotolinio valdymo pulto tiesinės korekcijos funkciją;
Pataisos principas: Per korekcijos funkciją, Kairiojo rato greitis yra patobulintas, kad pasiektų tokį patį greitį kaip ir dešinysis ratas, kad sinchronizuotų kairiojo ir dešiniojo ratų greitį ir pašalintų nuokrypį;
Nukrypimo korekcijos veikimo metodas: Rankiniu režimu, Paspauskite ir palaikykite “Įgalinti” mygtukas ir pasukite “Mažas variklio greičio reguliavimas”;
Pasukite pagal laikrodžio rodyklę, kad padidintumėte kairiojo rato greičio įtampą, o pataisos vertė ekrano ekrane padidės;
Pasukite prieš laikrodžio rodyklę, kad sumažintumėte kairiojo rato greičio įtampą ir ekrano pataisos vertę, kad sumažėtų;
Pataisos diapazonas: Pataisos vertė -90 į 90; Vieno korekcijos vieneto pataisos įtampa yra apie 0,02 V;

9. Parametrų meniu (Vartotojams draudžiama jį modifikuoti be leidimo)

Kai kurias nuotolinio valdymo funkcijas galima sureguliuoti per parametrus. Rankiniu režimu, Kai mažas variklio greitis S2 yra 10, Tris kartus iš eilės pastumkite į priekį/atvirkštinį jungiklį aukštyn, Ir tada tris kartus iš eilės nuspauskite žemyn, kad patektumėte į parametrų meniu;
Išeik iš parametrų meniu: Pasirinkite išsaugoti arba neišsaugoti, Tada paspauskite mygtuką Įgalinti, kad patvirtintumėte išėjimą;
Maksimali srovė: Pjovimo variklio eksploatavimo vertės srovė 80% iš šios srovės;
Greičio valdymo parametrai: Automatiniai pjovimo valdymo parametrai, Numatytasis 800, Modifikacija draudžiama;
Lėtėjimo parametras: Automatinis pjovimo valdymo parametras. Kai pjovimo srovės pokyčio vertė viršija šią vertę,deceleration begins.
Pagreitis A1: Automatinis pjovimo valdymo parametras, Kai pjovimo srovė yra mažesnė už nustatytą pjovimo srovę, pagreičio greitis;
Lėtėjimas A2: Automatinis pjovimo valdymo parametras, Kai pjovimo srovė yra didesnė už rinkinį
Pjaustymo srovė, lėtėjimo greitis;
Automatinis peilio atitraukimas: negaliojantis;
Pradėkite užsiblokuoti: 0, Jokio užsiblokavimo; 1, užsiblokuoti. Paspauskite įjungimo klavišą + forward and reverse to take effect and self-lock.
Maksimalus vaikščiojimas: the maximum speed of the small motor.
Pjaustymo srovė: Nustatykite maksimalią pagrindinio variklio srovę automatiniam pjovimui. Jei grįžtamojo ryšio srovė viršija šią vertę, it will start to decelerate.
Numatytasis greičio apribojimas: the default maximum speed of automatic cutting speed when turning on the machine.
Automatinis režimas: 0, Automatinis jungiklis yra automatiškai valdomas; 1, the automatic switch controls the automatic IO output point.
Greičio apribojimo poslinkis: the maximum speed of the small motor during automatic cutting.
Maksimalus šeimininkas: maximum speed of large motor.

Nuotolinio valdymo elektros charakteristikos

Nuotolinio valdymo dydis

The final interpretation right of this product belongs only to our company.