Konkreti „Siemens“ programa – „WixHC Technology“ https://www.wixhc.cn Pramonės lyderis Wed, 05 Nov 2025 06:21:59 +0000 lt hourly 1 https://wordpress.org/?v=6.8.3 Laidinio elektroninio rankračio naudojimo instrukcija https://www.wixhc.cn/product/wired-electronic-handwheel-instruction-manual Wed, 05 Nov 2025 06:13:13 +0000 https://www.wixhc.cn/?post_type=product&p=4678

1. Produkto įvadas

Electronic handwheel is used for manual guidance, positioning, tool alignment, and other operations on CNC machine tools. This model of electronic handwheel is a Siemens actual display wired electronic handwheel. The handwheel is connected to the X130 interface of the Siemens system through a network cable, and the system coordinates are read and displayed on the LCD screen of the handwheel through S7 protocol communication. The handwheel can also control system axis selection, padidinimas, buttons, andother signals through communication.
2.Product functional features
1. Prijungimui naudokite 6 gyslų aviacijos kištuką, su rankračio troso ilgiu 10 meters.
2. Rankinio rato ekrane gali būti rodomos sistemos ruošinio koordinatės, mechaninės koordinatės,padavimo greitis, ašies pasirinkimas, padidinimas, and other information.
3. Palaikykite avarinio sustabdymo mygtuką, Perjunkite IO signalo išvestį, and the hand wheel shutdown emergency stop is still valid.
4. Atramos 6 Pasirinktiniai mygtukai, perjungti IO signalus, and can output signals to the system through IO wiring or communication.
5. Atramos 6 arba 8 ašies valdymas, with switch IO signals that can be output to the system through IO wiring or communication.
6. Atramos 3 arba 4 levels of magnification control, with switch IO signals that can be output to the system through IO wiring or communication.
7. Support pulse encoder, 100 pulses/turn, can output signals to the system through AB pulse wiring.
8. Supports Siemens S7 protocol and Siemens 828D, 840DSL, ONE and other model systems.

 

3. Produkto specifikacijos
Handwheel working power supply voltage DC24V/1A
Receiver power supply voltage DC24V/1A
Receiver IO output load range DC24V
Hand wheel end cable length 10m
Receiver end cable length 1m
Receiver end network cable length 3m
Operating temperature -25℃<X<55℃
Anti-fall height 1m
Custom Button Quantity 6
Product dimensions 233*90.7*77.4（mm）

4.Produkto funkcijos įvadas

PASTABA:
Emergency stop button:
Press the emergency stop button, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.
After releasing the emergency stop, the emergency stop IO output on the receiver is closed, and all functions of the handwheel are restored.
② Screen display:

 

PLC: 0000 indicates that the network cable is not connected, PLC: 1010 indicates that the network cable is successfully connected to the PLC system.
PLC: 1110 represents successful writing of system data to the handwheel, PLC: 0001 represents successful connection to the computer.
③ Custom button:
6 Pasirinktiniai mygtukai, each corresponding to an IO output point on the receiver, also connected to the system through communication.
④ Axis selection switch:
The axis selection switch can switch the movement axis controlled by the handwheel.
⑤ Enable button:
Press and hold either enable button on both sides to activate the pulse encoder by shaking it. And the two groups on the receiver enable IO output to conduct, release the enable button to enable IO output to disconnect.
⑥ Magnification switch:The magnification switch can switch the magnification
controlled by the handwheel.
⑦ Pulse encoder:
Press and hold the enable button, shake the pulse encoder, emit a pulse signal, and control the movement of the machine axis.
⑧ Handwheel cable:

Cable connecting the handwheel and receiver, aviation plug, used for handwheel power supply and communication.

5. Product accessory diagram

6. Produkto diegimo vadovas
6.1 Product installation steps
1. Install the receiver into the electrical cabinet through the screw holes at the four corners.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the device to the receiver through cables and connect the receiver to the X130 interface of the system using Ethernet cables.
3. After fixing the receiver, install the aviation plug base at the handwheel opening position on the panel, and plug the other end of the base into the handwheel interface on the receiver. Then insert the aviation plug of the handwheel cable into the base and tighten the fixing device.

 

6.2 Receiver installation dimensions

6.3 Installation dimensions of aviation plugs

6.4 Receiver Wiring Reference Diagram
7.Produkto operacijos instrukcijos

1. When the receiver is powered on and the working indicator light of the receiver flashes, connect the receiver to the computer with a network cable, set the fixed IP address of the computer, and use the network configuration tool software to set the network parameters of the handwheel function. For specific setting methods, refer to the “LXWGP-ETS Wired Handwheel User Manual”.

2.After the receiver is set up, the system needs to program a PLC program. Please refer to the “LXWGP-ETS Different Siemens Numerical Control System Setting Methods” and PLC program routine materials for details.

3.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.

4.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X interface of the system. Connect the receiver power supply and pulse line.
5. Select axis selection: Switch the axis selection switch and select the axis you want to operate on.
6. Select magnification: Switch the magnification switch and select the magnification level you need.
7. Moving axis: Press and hold the enable button, select the axis selection switch, select the magnification switch, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.
8. Press and hold any custom button to turn on the IO output of the corresponding button in the receiver, and release the button to turn off the output.
9. Press the emergency stop button, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled, release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
8.Product Model Description

① LXWGP represents a wired appearance style, and the receiver communication interface
is an Ethernet interface.
② : Represents Siemens system specific.
③ : represents the number of axis selection switches, represents axes, and represents
axes.
④ : represents the type of axis selection and magnification signal, A represents
point-to-point output signal, and B represents encoded output signal.

9.Product trouble shooting

10.Maintenance
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. Please avoid squeezing, falling, bumping, ir tt. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. Jei ilgai nenaudojamas, please store the handwheel in a clean and safe place.During storage and transportation, attention should be paid to moisture and shock resistance.
11. Informacija apie saugą

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. If any abnormal situation occurs with the handwheel, please stop using it immediately and troubleshoot. Before troubleshooting, it is forbidden to use the faulty handwheel again to avoid safety accidents caused by unknown handwheel faults;
3. Jei reikia remonto, Kreipkitės į gamintoją. If the damage is caused by self repair, Gamintojas nepateiks garantijos

 

]]> Dedikuotas belaidis nuotolinio valdymo pultas CNC vertikalioms tekinimo staklės Veikimo instrukcijoms https://www.wixhc.cn/product/vertical-lathe-wireless-electronic-handwheel-copy Wed, 03 Sep 2025 01:06:33 +0000 https://www.wixhc.cn/?post_type=product&p=4666

1.Produkto įvadas

The dedicated wireless remote contro for CNC vertical lathes is used for manual guidance, positioning, tool setting, and other operations on CNC vertical machine tools. This product adopts wireless transmission technology, eliminating the need for traditional spring wirae connections, reducing equipment failures caused by cables, and eliminating the disadvantages of cable dragging and oil stains, making operation more convenient. It is widely applicable to various vertical lathes such as CNC vertical lathes, single-column vertical lathes, and double-column vertical lathes.It can also be adapted to a variety of CNC systems on the market, such as Siemens,
Mitsubishi, Fanuc, and Syntec.

2. Product functional features

1. Adopting 433 MHz wireless communication technology, with a wireless operating distance of 40 meters.
2.Adopting automatic frequency hopping function and using 32 sets of wireless remote controllers simultaneously, without affecting each other.
3. Palaikykite avarinio sustabdymo mygtuką, switch IO signal output.
4. Atramos 2 pritaikomi mygtukai, with switch-type IO signal output.
5. Atramos -2 axis control.
6. Supports 3-level magnification control.
7. Support the enable button function, which can output on/off IO signals and control axis selection, multiplying factor, and encoder.
8. Support for axis selection and magnification modification through software to change the encoding type.
9. Supports pulse encoder, with a specification of 100 pulses per revolution.
3. Produkto specifikacijos
Operating voltage and current of wireless remote
3V/14MA
Battery specifications 2 AA alkaline batteries, size 5
Low voltage alarm range of wireless remote < 2.3V
Receiver power supply voltage DC5V-24V/A
Receiver emergency stop output load range AC125V-1A/DC30V-2A
Receiver enable output load range
AC125V-1A/DC30V-2A
Receiver custom button output load range DC24V/50mA
Receiver axis selection output load range DC24V/50mA
Receiver magnification output load range DC24V/50mA
Transmission power of handheld terminal
15dBm
Receiver receiving sensitivity -100dBm
Wireless communication frequency 433MHz frequency band
Wireless communication distance Barrier free distance of 40 metrai
Operation temperature -25℃ < X < 55℃
Anti fall height 1 (matuoklis)
Custom button quantity 2
4. Product Function Introduction



Pastabos:

① Pulse encoder:
Press and hold the enable button, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Žemos įtampos aliarmo lemputė, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Press the emergency stop button, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (power switch):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

5. Product accessory diagram

6. Produkto diegimo vadovas
6.1 Product installation steps

1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, the antenna equipped with the receiver must be connected, and the outer end of the antenna should be installed or placed outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for the best signal effect. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Finally, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Receiver installation dimensions

6.3 Receiver Wiring Reference Diagram

7. Product operation instructions
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, ir
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Select the coordinate axis: Press and hold the enable button, toggle the axis selection switch, and select the axis you want to operate.
3. Select magnification: Press and hold the enable button, toggle the magnification switch,and select the desired magnification level.
4. Moving axis: Press and hold the enable button, select the axis selection switch, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Press and hold any custom button, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Press the emergency stop button, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. If the handwheel is not operated for a period of time, it will automatically enter sleep mode to reduce power consumption. When it is used again, the handwheel can be activated by pressing the enable button.
8. If the handwheel is not used for a long time, it is recommended to switch the handwheel shaft to the OFF position, turn off the handwheel power, and extend the battery life.

8. Product Model Description

① :ZTWGP represents the appearance style
②：Pulse output parameters:
01: Indicates that the pulse output signal is A, B; Pulse voltage 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Pulse voltage 5V; pulse quantity 100PPR.
04：Indicates a low-level NPN open circuit output, with pulse output signals of A and B;The number of pulses is 100PPR.
05：Indicates high-level PNP source output, with pulse output signals of A and B; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 represents 2 axes.
④：Represents the type of axis selection switch signal, A represents point-to-point output signal, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, A represents point-to-point output signal, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 represents 2 custom buttons.
⑦：Represents the power supply for the system handwheel, ir 05 represents 5V power supply.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions

10. Product maintenance

1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. Please avoid squeezing, falling, bumping, ir tt. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. Jei ilgai nenaudojamas, please store the handwheel in a clean and safe place. During storage and transportation, attention should be paid to moisture and shock resistance.

11. Informacija apie saugą

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery level is too low to avoid errors caused by insufficient battery power and inability to operate the handwheel.
3. Jei reikia remonto, Kreipkitės į gamintoją. If the damage is caused by self repair, Gamintojas nepateiks garantijos

]]> „Fanuc“ skirtas belaidis elektroninis ratas https://www.wixhc.cn/product/fanuc-dedicated-wireless-electronic-handwheel Tue, 06 Gegužė 2025 07:26:48 +0000 https://www.wixhc.cn/?post_type=product&p=4626

1.Produkto įvadas

Wireless electronic handwheel is used for manual guidance, positioning, tool alignment,and other operations on CNC machine tools. This product adopts wireless transmission technology, eliminating the traditional spring wire connection, reducing equipment failures caused by cables, eliminating the disadvantages of cable dragging and oil stains, ir padaryti operaciją patogiau. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,padidinimas, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. Produkto savybės
1. Priimkite 433MHz belaidžio ryšio technologiją, Belaidžio veikimo atstumas yra 40 metrai;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the same time without affecting each other;
3. Palaikykite avarinio sustabdymo mygtuką, Perjunkite IO signalo išvestį, connected to the system through IO wiring;
4. Palaikymas 4 Pasirinktiniai mygtukai, Perjunkite IO signalą, išvesties signalas sistemai per IO-Link protokolą;
5. Palaikykite greito judėjimo mygtuką + ir mygtukas -, Paspauskite ir palaikykite mygtuką, kad pakeistumėte rankinį ratą, kad perkeltumėte mašiną;
6. Palaikykite 6 ašių valdymą, Perjunkite IO signalą, išvesties signalas sistemai per IO-Link protokolą;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

Pastabos:
①Emergency stop button:
Press the emergency stop button, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 Pasirinktiniai mygtukai, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.

5.Produktų priedų schema

6.Produkto diegimo vadovas

6.1 Product Installation Steps

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3. After the receiver is fixed, the antenna equipped with the receiver must be connected,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. It
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4.Finally, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 Receiver installation dimensions

6.3 Receiver Wiring Reference Diagram

7. Priežiūra ir priežiūra

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
tarnavimo gyvenimas;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. Please avoid squeezing, falling, bumping, ir tt. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. Jei ilgai nenaudojamas, please store the handwheel in a clean and safe place;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. Prieš naudodamiesi atidžiai perskaitykite instrukcijas. Neprofesionalams draudžiama
operating.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. Jei reikia remonto, Kreipkitės į gamintoją. Jei žalą padaro savarankiškas atsiliepimas,
the manufacturer will not provide warranty.

]]> „Siemens“ skirtas belaidžio elektroninio rato XWGP-ETS https://www.wixhc.cn/product/siemens-dedicated-wireless-electronic-handwheel-xwgp-ets Thu, 26 Gegužė 2022 02:33:53 +0000 https://www.wixhc.cn/?post_type=product&p=4381

1.Nuotolinio valdymo pulto pristatymas

a.Produkto kompozicija
Siemens realaus laiko koordinačių ekranas belaidis elektroninis rankratis susideda iš dviejų dalių: elektroninis rankinis ratas + imtuvas;

b. Charakteristikos

*Palaikykite „Siemens PLC“: S7-200/-300/-1200；Palaikykite „Siemens“ sistemos koordinačių verčių realiojo laiko rodymą；
*Atidarytas belaidžio perdavimo atstumas 40 metrai, automatinio dažnio šuoliavimo technologija, gali naudoti 32 įrangos komplektų vienu metu;
*Elektroninis rankratis yra varomas 2 AA baterijos ir gali būti naudojamos ilgiau nei 30 dienos;
*Imtuvas turi išorinę anteną, kad sustiprintų signalą, ir jį lengva montuoti;
*Elektroninė rankinio rato atrama: Vienas 100ppr kodavimo įrenginys 、Vieno 6 greičių ašies pasirinkimo jungiklis 、 vienas 3 greičių padidinimo jungiklis;
*Elektroninės rankračio atramos 6 Pasirinktiniai mygtukai, atitinkantis Siemens PLC adresą, kurį galima laisvai užprogramuoti;

*6 Pasirinktiniai mygtukai gali valdyti 6 perjungimo išėjimai;
*Ekrane realiuoju laiku rodoma atitinkama PLC registro koordinačių reikšmė, and supports 6-axis display of real-time coordinates.

2.Taikymo laukas

Programuojamas CNC nuotolinio valdymo pultas yra plačiai naudojamas įvairiose CNC srityse, tokiose kaip lazerinio graviravimo sistema, CNC frezavimo mašina, CNC apdirbimo centras, portalinis staklės, kt.

3. Įvadas į darbo principą

1）Elektroninis rankratis yra prijungtas prie PLC per Ethernet imtuvą

a.Ratas belaidžiu būdu perduoda pagrindinius duomenis į imtuvą, o imtuvas rašo raktus per tinklo kabelį PLC sistemos DB sritį; imtuvas nuskaito rodytinus duomenis iš nurodytos DB srities, ir grąžina duomenis į rankinio rato ekraną. Vartotojas gali tinkinti pagrindinį DB skaitymo ir rašymo adresą ant rankračio, so that the handwheel can read and write the data in the DB area of the PLC.

b. Imtuvas palaiko Siemens S7 protokolą. Taikoma PLC S7-200, PLC S7-300 and PLC S7-1200.

c. The user can configure the receiver to server mode and client mode through the PLC connection configuration tool.

Serverio režimu, vartotojas sukonfigūruoja PLC skaitymo ir rašymo adresą per WGP-ETS konfigūravimo programinę įrangą;Norėdami sukonfigūruoti imtuvą į kliento režimą, naudokite PLC ryšio konfigūravimo įrankį. Po konfigūracijos, the XWGP-ETS receiver can communicate with the PLC through the standard S7 protocol.

2)Konkretus pritaikymas

Specifinis rankračio imtuvo ir Siemens PLC S7-200 pritaikymas:

a. Mygtukas ant rankračio atitinka BOOL srities reikšmę, kurią vartotojas nustatė PLC. Jei paspaudžiamas rankračio mygtukas, atitinkama BOOL sritis yra teisinga, ir kai jis bus paleistas, tai netikra, o pagrindinį BOOL srities adresą galima nustatyti rankračiu;

b. Rankratis gali nuskaityti DB srities reikšmę PLC. Viena ašis turi 4 baitų rodymo duomenų, ir 6 ašys turi iš viso 24 baitų. The base address of the DB area can be set through the WGP-ETS configuration software.

4.Išvaizdos įvadas

5.Imtuvo terminalo apibrėžimas ir kodavimo lentelė

6.Išvaizdos dydis

 

 

]]>