Penerangan
1.Model Produk
Model: DH12S-P6S
Peralatan yang berkenaan:Mesin gergaji sawit/bilah sawah
2.Rajah Aksesori Produk
Catatan: Anda boleh memilih salah satu daripada tiga antena. Antena cawan sedutan adalah standard secara lalai.
3.Penerangan suis kawalan jauh
4.PENGENALAN PENGENALAN
Kelajuan motor utama: Utama: 0-50
Melancarkan kelajuan motor: Garis: 0-50
Had kelajuan maksimum motor perjalanan pemotongan automatik: Kelajuan: 0-30
(Parameter boleh laras)
Semasa pemotongan automatik menetapkan semasa: Menetapkan: 28 (Parameter boleh laras)
Kelajuan Motor Lengan Swing: Ayunan: 0-50
Voltan rendah: Bateri kawalan jauh terlalu rendah, Sila ganti bateri.
Rangkaian jatuh: Isyarat wayarles terganggu. Sila periksa kuasa penerima, Kuasa lagi, dan mulakan semula kawalan jauh.
5.Arahan Operasi Fungsi Kawalan Jauh
1）Turn on the remote control
Apabila penerima dikuasakan, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; Pasang dua bateri AA di kawalan jauh, Hidupkan suis kuasa, and the display will show the motor speed, menunjukkan permulaan yang berjaya.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, putar “Ke hadapan/terbalik” beralih ke hadapan, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, putar “Ke hadapan/terbalik” beralih ke terbalik, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Putar “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, putar “Ke hadapan/terbalik” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Putar “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Tekan dan tahan “speed adjustment enable” butang dan putar “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; Langkah kedua ialah menyesuaikan had kelajuan maksimum motor berjalan; Langkah ketiga adalah untuk menggerakkan “ke hadapan/terbalik” Tukar ke hadapan atau ke belakang untuk memasukkan mod pemotongan automatik;
7) Menu parameter (Pengguna dilarang mengubahnya tanpa kebenaran)
Masukkan menu parameter:Dalam mod manual, Apabila kelajuan motor utama adalah 0, Tolak suis ke hadapan/terbalik tiga kali berturut -turut, dan kemudian menolaknya tiga kali berturut -turut untuk memasuki menu parameter;
Keluar dari menu parameter: Hidupkan Tombol Pelarasan Kelajuan, Pilih Simpan atau Tidak Simpan, dan tekan butang Enable untuk mengesahkan;
Arus dinilai: Nilai maksimum arus motor utama, unit ampere;
Parameter Pelarasan Kelajuan: Parameter kawalan pemotongan automatik, lalai 800, Unit Milli Kedua,pengubahsuaian dilarang;
Parameter penurunan: Apabila nilai perubahan semasa pemotongan melebihi nilai ini, rapid deceleration begins, unit ampere;
Pecutan A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Penurunan A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, pengubahsuaian dilarang;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, pengubahsuaian dilarang;
Maximum current: The range of main motor feedback current, unit ampere;
Maximum host: Remote control main motor speed adjustment display range;
Berjalan maksimum: Invalid parameter;
Speed limit offset: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automatic cutting, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,ia akan berada dalam mod pemalasan.Jika lebih besar nilai ini, ia akan keluar dari mod pemalasan dan masukkan mod pemotongan.Unit adalah ampere;
Arus tanpa beban:Apabila mod automatik bermula, if the main motor feedback current is less than this value,ia berada dalam mod tanpa beban.Jika lebih besar nilai ini, ia akan keluar dari mod tanpa beban dan masukkan mod pemotongan.;
Kelajuan lengan ayunan: Kelajuan awal motor lengan ayunan ketika memulakan;
Mod pemotongan: Tukar antara bilah saw dan dawai melihat mod, dan parameter akan beralih sewajarnya selepas suis; dalam mod saw bilah, Paparan Kawalan Jauh Menambah Motor Lengan Swing, Semasa dalam mod gergaji wayar, tidak ada motor lengan ayunan;
Masa yang dihancurkan: Apabila arus maklum balas motor utama melebihi arus berhenti, arus maklum balas akan dikesan secara berterusan. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
6.Ciri -ciri Elektrik Kawalan Jauh
7.Saiz kawalan jauh
Hak tafsiran akhir produk ini hanya milik syarikat kami.
