Wireless Handwheel Elettroniku – Teknoloġija WIXHC https://www.wixhc.cn Industry Leader Wed, 05 Nov 2025 06:21:59 +0000 mt hourly 1 https://wordpress.org/?v=6.8.3 Manwal tal-Istruzzjoni tal-handwheel elettroniku bil-fili https://www.wixhc.cn/product/wired-electronic-handwheel-instruction-manual Wed, 05 Nov 2025 06:13:13 +0000 https://www.wixhc.cn/?post_type=product&p=4678

1. Introduzzjoni tal-Prodott

Electronic handwheel is used for manual guidance, pożizzjonament, tool alignment, and other operations on CNC machine tools. This model of electronic handwheel is a Siemens actual display wired electronic handwheel. The handwheel is connected to the X130 interface of the Siemens system through a network cable, and the system coordinates are read and displayed on the LCD screen of the handwheel through S7 protocol communication. The handwheel can also control system axis selection, magnification, buttons, andother signals through communication.
2.Karatteristiċi funzjonali tal-prodott
1. Use a 6-core aviation plug cable for connection, with a handwheel cable length of 10 meters.
2. The handwheel screen can display system workpiece coordinates, mechanical coordinates,feed rate, axis selection, magnification, and other information.
3. Tappoġġja l-buttuna ta 'waqfien ta' emerġenza, swiċċ output tas-sinjal io, and the hand wheel shutdown emergency stop is still valid.
4. Jappoġġja 6 buttuni tad-dwana, switch IO signals, and can output signals to the system through IO wiring or communication.
5. Jappoġġja 6 or 8 Kontroll tal-assi, with switch IO signals that can be output to the system through IO wiring or communication.
6. Jappoġġja 3 or 4 levels of magnification control, with switch IO signals that can be output to the system through IO wiring or communication.
7. Support pulse encoder, 100 pulses/turn, can output signals to the system through AB pulse wiring.
8. Supports Siemens S7 protocol and Siemens 828D, 840DSL, ONE and other model systems.

 

3. Speċifikazzjonijiet tal-prodott
Handwheel working power supply voltage DC24V/1A
Vultaġġ tal-provvista tal-enerġija riċevitur DC24V/1A
Receiver IO output load range DC24V
Hand wheel end cable length 10m
Receiver end cable length 1m
Receiver end network cable length 3m
Operating temperature -25℃<X<55℃
Anti-fall height 1m
Custom Button Quantity 6
Product dimensions 233*90.7*77.4（mm）

4.Product function introduction

Nota:
Emergency stop button:
Agħfas il-buttuna ta 'waqfien ta' emerġenza, u ż-żewġ settijiet ta 'outputs ta' waqfien ta 'emerġenza fuq ir-riċevitur jiġu skonnettjati, and all functions of the handwheel will be invalid.
After releasing the emergency stop, the emergency stop IO output on the receiver is closed, and all functions of the handwheel are restored.
② Screen display:

 

PLC: 0000 indicates that the network cable is not connected, PLC: 1010 indicates that the network cable is successfully connected to the PLC system.
PLC: 1110 represents successful writing of system data to the handwheel, PLC: 0001 represents successful connection to the computer.
③ Custom button:
6 buttuni tad-dwana, kull wieħed jikkorrispondi għal punt ta 'ħruġ IO fuq ir-riċevitur, also connected to the system through communication.
④ Axis selection switch:
The axis selection switch can switch the movement axis controlled by the handwheel.
⑤ Enable button:
Press and hold either enable button on both sides to activate the pulse encoder by shaking it. And the two groups on the receiver enable IO output to conduct, release the enable button to enable IO output to disconnect.
⑥ Magnification switch:The magnification switch can switch the magnification
controlled by the handwheel.
⑦ Pulse encoder:
Agħfas u żomm il-buttuna Enable, ħawwad il-encoder tal-polz, Emit sinjal tal-polz, and control the movement of the machine axis.
⑧ Handwheel cable:

Cable connecting the handwheel and receiver, aviation plug, used for handwheel power supply and communication.

5. Dijagramma Aċċessorja tal-Prodott

6. Gwida għall-Installazzjoni tal-Prodott
6.1 Passi ta 'installazzjoni tal-prodott
1. Install the receiver into the electrical cabinet through the screw holes at the four corners.
2. Irreferi għad-dijagramma tal-wajers tar-riċevitur tagħna u qabbelha mat-tagħmir tiegħek fuq il-post. Connect the device to the receiver through cables and connect the receiver to the X130 interface of the system using Ethernet cables.
3. After fixing the receiver, install the aviation plug base at the handwheel opening position on the panel, and plug the other end of the base into the handwheel interface on the receiver. Then insert the aviation plug of the handwheel cable into the base and tighten the fixing device.

 

6.2 Dimensjonijiet ta 'installazzjoni tar-riċevitur

6.3 Installation dimensions of aviation plugs

6.4 Dijagramma ta 'referenza tal-wajers tar-riċevitur
7.Product Operation Instructions

1. When the receiver is powered on and the working indicator light of the receiver flashes, connect the receiver to the computer with a network cable, set the fixed IP address of the computer, and use the network configuration tool software to set the network parameters of the handwheel function. For specific setting methods, refer to the “LXWGP-ETS Wired Handwheel User Manual”.

2.After the receiver is set up, the system needs to program a PLC program. Please refer to the “LXWGP-ETS Different Siemens Numerical Control System Setting Methods” and PLC program routine materials for details.

3.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.

4.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X interface of the system. Connect the receiver power supply and pulse line.
5. Select axis selection: Switch the axis selection switch and select the axis you want to operate on.
6. Agħżel ingrandiment: Switch the magnification switch and select the magnification level you need.
7. Assi li jiċċaqlaq: Agħfas u żomm il-buttuna Enable, Agħżel is-swiċċ tal-għażla tal-assi, Agħżel is-swiċċ tal-ingrandiment, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.
8. Press and hold any custom button to turn on the IO output of the corresponding button in the receiver, and release the button to turn off the output.
9. Agħfas il-buttuna ta 'waqfien ta' emerġenza, L-output tal-IO ta 'Emerġenza Korrispondenti tar-riċevitur se jkun skonnettjat, Il-funzjoni tal-handwheel se tkun diżattivata, Irrilaxxa l-buttuna ta 'waqfien ta' emerġenza, Il-ħruġ ta 'IO ta' waqfien ta 'emerġenza se jkun magħluq, and the handwheel function will be restored.
8.Deskrizzjoni tal-Mudell tal-Prodott

① LXWGP represents a wired appearance style, and the receiver communication interface
is an Ethernet interface.
② : Represents Siemens system specific.
③ : represents the number of axis selection switches, represents axes, and represents
axes.
④ : represents the type of axis selection and magnification signal, A represents
point-to-point output signal, and B represents encoded output signal.

9.Product trouble shooting

10.Maintenance
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. Jekk jogħġbok evita li tagħfas, jaqa ', bumping, eċċ. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. Jekk ma jintużax għal żmien twil, please store the handwheel in a clean and safe place.During storage and transportation, attention should be paid to moisture and shock resistance.
11. Informazzjoni dwar is-sigurtà

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. If any abnormal situation occurs with the handwheel, please stop using it immediately and troubleshoot. Before troubleshooting, it is forbidden to use the faulty handwheel again to avoid safety accidents caused by unknown handwheel faults;
3. Jekk hija meħtieġa t-tiswija, Jekk jogħġbok ikkuntattja lill-manifattur. Jekk il-ħsara hija kkawżata minn tiswija personali, Il-manifattur ma jipprovdix garanzija

 

]]> Remot bla fili dedikat għal struzzjonijiet ta 'operazzjoni ta' torn vertikali CNC https://www.wixhc.cn/product/vertical-lathe-wireless-electronic-handwheel-copy Wed, 03 Sep 2025 01:06:33 +0000 https://www.wixhc.cn/?post_type=product&p=4666

1.Introduzzjoni tal-Prodott

Il-kontro remot bla fili ddedikat għal tornijiet vertikali CNC jintuża għal gwida manwali, pożizzjonament, issettjar tal-għodda, u operazzjonijiet oħra fuq għodod tal-magni vertikali CNC. Dan il-prodott jadotta teknoloġija ta 'trasmissjoni mingħajr fili, telimina l-ħtieġa għal konnessjonijiet tradizzjonali tar-rebbiegħa wirae, Tnaqqis tal-fallimenti tat-tagħmir ikkawżati minn kejbils, u l-eliminazzjoni tal-iżvantaġġi tat-tkaxkir tal-kejbil u t-tbajja taż-żejt, Nagħmlu l-Operazzjoni Aktar Konvenjenti. Huwa applikabbli ħafna għal diversi tornijiet vertikali bħal tornijiet vertikali CNC, torn vertikali ta 'kolonna waħda, u torn vertikali ta 'kolonna doppja. Jista' jkun adattat ukoll għal varjetà ta 'sistemi CNC fis-suq, bħal Siemens,
Mitsubishi, FANUC, and Syntec.

2. Karatteristiċi funzjonali tal-prodott

1. Adozzjoni 433 Teknoloġija tal-Komunikazzjoni Wireless MHZ, b'distanza operattiva bla fili ta ' 40 meters.
2.L-adozzjoni tal-funzjoni awtomatika tal-qbiż tal-frekwenza u l-użu 32 settijiet ta 'kontrolluri remoti mingħajr fili fl-istess ħin, without affecting each other.
3. Tappoġġja l-buttuna ta 'waqfien ta' emerġenza, switch IO signal output.
4. Jappoġġja 2 buttuni customizable, with switch-type IO signal output.
5. Jappoġġja -2 axis control.
6. Supports 3-level magnification control.
7. Appoġġ il-funzjoni tal-buttuna Enable, li jista 'joħroġ is-sinjali IO mixgħul / mitfi u l-għażla tal-assi tal-kontroll, fattur li jimmultiplika, and encoder.
8. Support for axis selection and magnification modification through software to change the encoding type.
9. Jappoġġja l-encoder tal-polz, bi speċifikazzjoni ta ' 100 pulses per revolution.
3. Speċifikazzjonijiet tal-prodott
Vultaġġ operattiv u kurrent ta 'wireless remote
3V / 14Ma
Speċifikazzjonijiet tal-batterija 2 AA batteriji alkalini, size 5
Firxa ta 'allarm ta' vultaġġ baxx ta 'remot bla fili < 2.3V
Vultaġġ tal-provvista tal-enerġija riċevitur DC5V-24V / A.
Riċevitur ta 'Emerġenza Waqqaf il-firxa tat-tagħbija AC125V-1A / DC30V-2A
Riċevitur jippermetti firxa tat-tagħbija tal-ħruġ
AC125V-1A / DC30V-2A
Firxa tat-tagħbija tal-buttuna tad-dwana riċevitur DC24V / 50mA
Assi tar-riċevitur Għażla tal-firxa tat-tagħbija tal-ħruġ DC24V / 50mA
Firxa tat-tagħbija tal-ingrandiment tar-riċevitur DC24V / 50mA
Qawwa tat-trasmissjoni tat-terminal li jinżamm fl-idejn
15DBM
Riċevitur li jirċievi sensittività -100DBM
Frekwenza ta 'komunikazzjoni mingħajr fili 433Banda tal-frekwenza MHz
Distanza ta 'komunikazzjoni mingħajr fili Distanza ħielsa mill-barriera ta ' 40 miters
Temperatura tat-tħaddim -25℃ < X < 55℃
L-għoli tal-waqgħa 1 (meter)
Kwantità tal-buttuna tad-dwana 2
4. Introduzzjoni tal-funzjoni tal-prodott



Noti:

① Encoder tal-polz:
Agħfas u żomm il-buttuna Enable, ħawwad il-encoder tal-polz, Emit sinjal tal-polz,and control the movement ofthe machine axis.
② Enable buttuna:
Agħfas jew buttuna Enable fuq kull naħa, u ż-żewġ settijiet ta 'outputs IO li jistgħu jmexxu r-riċevitur. Irrilaxxa l-buttuna Enable biex tiskonnettja l-output Enable IO; U qabel ma taqleb l-ingrandiment tal-għażla tal-assi u tħawwad il-handwheel,il-buttuna Enable teħtieġ li tinżamm biex tkun effettiva; This function can be cancelled through configuration software.

③ Dwal tal-indikatur:
Dawl tax-xellug: qawwa fuq dawl,il-handwheel juża l-assi biex jagħżel għall-qawwa fuq, U dan id-dawl jibqa 'mixgħul wara l-enerġija mixgħula;
Dawl tan-nofs: Dawl tas-sinjal li jixgħel meta tħaddem kwalunkwe funzjoni tal-handwheel, u ma jixgħelx meta ma jkun hemm l-ebda operazzjoni;
Dawl tal-lemin: Dawl ta 'allarm ta' vultaġġ baxx, Livell baxx ta 'batterija,din il-lightflashes jew tibqa 'mixgħula, battery needs to be replaced.

④ buttuna ta 'waqfien ta' emerġenza:
Agħfas il-buttuna ta 'waqfien ta' emerġenza, u ż-żewġ settijiet ta 'outputs ta' waqfien ta 'emerġenza fuq ir-riċevitur jiġu skonnettjati, and all functions of the handwheel will be invalid.

⑤ Swiċċ tal-ingrandiment:
Agħfas u żomm il-buttuna Enable biex taqleb is-swiċċ tal-ingrandiment, which can switch the magnification controlled by the handwheel.

Swiċċ tal-Għażla tal-Assi (swiċċ tal-qawwa):
Agħfas u żomm il-buttuna Enable biex taqleb is-swiċċ tal-għażla tal-assi, li jista 'jaqleb l-assi tal-moviment ikkontrollat ​​mill-handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ buttuna tad-dwana:
Żewġ buttuni tad-dwana, each corresponding to an IO output point on the receiver.

5. Dijagramma Aċċessorja tal-Prodott

6. Gwida għall-Installazzjoni tal-Prodott
6.1 Passi ta 'installazzjoni tal-prodott

1. Installa r-riċevitur fil-kabinett elettriku minn ġol-bokkla fuq wara, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Irreferi għad-dijagramma tal-wajers tar-riċevitur tagħna u qabbelha mat-tagħmir tiegħek fuq il-post. Connect the equipment to the receiver via cables.
3.Wara li r-riċevitur ikun iffissat kif suppost, L-antenna mgħammra mar-riċevitur għandha tkun konnessa, u t-tarf ta 'barra ta' l-antenna għandu jkun installat jew imqiegħed barra l-kabinett elettriku. Huwa rrakkomandat li tpoġġiha fuq il-parti ta 'fuq tal-kabinett elettriku għall-aħjar effett tas-sinjal. Huwa pprojbit li tħalli l-antenna mhux konnessa jew poġġiha ġewwa l-kabinett elettriku, as this may result in the signal being unusable.
4. Fl-aħħarnett, Ixgħel is-swiċċ tal-qawwa tal-handwheel, and you can operate the machine remotely using the handwheel.

6.2 Dimensjonijiet ta 'installazzjoni tar-riċevitur

6.3 Dijagramma ta 'referenza tal-wajers tar-riċevitur

7. Istruzzjonijiet dwar l-Operazzjoni tal-Prodott
1. Qawwa fuq il-magna u r-riċevitur. Id-dawl tal-indikatur tax-xogħol tar-riċevitur jixgħel. Installa l-batterija fil-handwheel elettroniku bla fili, Żgura l-għata tal-batterija, u
Ixgħel is-swiċċ tal-qawwa tal-handwheel elettroniku mingħajr fili. The handwheel’s battery level indicator light is on.
2. Agħżel l-assi tal-koordinati: Agħfas u żomm il-buttuna Enable, Toggle l-iswiċċ tal-għażla tal-assi, and select the axis you want to operate.
3. Agħżel ingrandiment: Agħfas u żomm il-buttuna Enable, Toggle l-iswiċċ tal-ingrandiment,and select the desired magnification level.
4. Assi li jiċċaqlaq: Agħfas u żomm il-buttuna Enable, Agħżel is-swiċċ tal-għażla tal-assi, Agħżel is-swiċċ tal-ingrandiment, u mbagħad dawwar il-encoder tal-polz. Dawwar lejn il-lemin biex tiċċaqlaq
positive axis and counterclockwise to move the negative axis.
5. Agħfas u żomm kwalunkwe buttuna tad-dwana, u l-buttuna korrispondenti tal-output IO tar-riċevitur tkun mixgħula. Itlaq il-buttuna, and the output will be turned off.
6. Agħfas il-buttuna ta 'waqfien ta' emerġenza, L-output tal-IO ta 'Emerġenza Korrispondenti tar-riċevitur se jkun skonnettjat, Il-funzjoni tal-handwheel se tkun diżattivata,Irrilaxxa l-buttuna ta 'waqfien ta' emerġenza, Il-ħruġ ta 'IO ta' waqfien ta 'emerġenza se jkun magħluq, and the handwheel function will be restored.
7. Jekk il-handwheel ma jitħaddemx għal perjodu ta 'żmien, awtomatikament jidħol fil-modalità ta 'rqad biex tnaqqas il-konsum tal-enerġija. Meta jerġa 'jintuża, the handwheel can be activated by pressing the enable button.
8. Jekk il-handwheel ma jintużax għal żmien twil, huwa rrakkomandat li tinbidel ix-xaft tal-handwheel għall-pożizzjoni off, Itfi l-qawwa tal-handwheel, and extend the battery life.

8. Deskrizzjoni tal-Mudell tal-Prodott

① :ZTWGP jirrappreżenta l-istil tad-dehra
②：Parametri tal-ħruġ tal-polz:
01: Jindika li s-sinjal tal-ħruġ tal-polz huwa, B; Vultaġġ tal-polz 5V; pulse quantity 100PPR.
02：Li jindika li s-sinjali tal-ħruġ tal-polz huma a u b; Vultaġġ tal-polz 12V; pulse quantity 100PPR.
03：Li jindika li s-sinjali tal-ħruġ tal-polz huma, B, A -, B -; Vultaġġ tal-polz 5V; pulse quantity 100PPR.
04：Jindika output taċ-ċirkwit miftuħ NPN ta 'livell baxx, b'sinjali tal-ħruġ tal-polz ta 'a u b;The number of pulses is 100PPR.
05：Jindika output tas-sors tal-PNP ta 'livell għoli, b'sinjali tal-ħruġ tal-polz ta 'a u b; The number of pulses is 100PPR.
③：Jirrappreżenta n-numru ta 'swiċċijiet tal-għażla tal-assi, 2 jirrappreżenta 2 axes.
④：Jirrappreżenta s-sinjal tat-tip ta 'swiċċ tal-għażla tal-assi, A tirrappreżenta sinjal tal-ħruġ minn punt għal punt, and B represents encoded output signal.
⑤：Jirrappreżenta t-tip ta 'sinjal tal-iswiċċ tal-multiplikazzjoni, A tirrappreżenta sinjal tal-ħruġ minn punt għal punt, and B represents encoded output signal.
⑥：Jirrappreżenta n-numru ta 'buttuni tad-dwana, 2 jirrappreżenta 2 custom buttons.
⑦：Jirrappreżenta l-provvista tal-enerġija għas-sistema handwheel, u 05 represents 5V power supply.
⑧：L jirrappreżenta l-kolonna tax-xellug (Detentur tas-sikkina tax-xellug), u r jirrappreżenta l-kolonna t-tajba (Detentur tal-lemin tas-sikkina).

9.Soluzzjoni għal malfunzjonijiet tal-prodott

10. Manutenzjoni tal-Prodott

1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. Jekk jogħġbok evita li tagħfas, jaqa ', bumping, eċċ. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. Jekk ma jintużax għal żmien twil, Jekk jogħġbok aħżen il-handwheel f'post nadif u sigur. Matul il-ħażna u t-trasport, attention should be paid to moisture and shock resistance.

11. Informazzjoni dwar is-sigurtà

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery level is too low to avoid errors caused by insufficient battery power and inability to operate the handwheel.
3. Jekk hija meħtieġa t-tiswija, Jekk jogħġbok ikkuntattja lill-manifattur. Jekk il-ħsara hija kkawżata minn tiswija personali, Il-manifattur ma jipprovdix garanzija

]]> FANUC iddedikat bla fili elettronika handwheel https://www.wixhc.cn/product/fanuc-dedicated-wireless-electronic-handwheel Tue, 06 Mejju 2025 07:26:48 +0000 https://www.wixhc.cn/?post_type=product&p=4626

1.Introduzzjoni tal-Prodott

Wireless electronic handwheel is used for manual guidance, pożizzjonament, tool alignment,and other operations on CNC machine tools. Dan il-prodott jadotta teknoloġija ta 'trasmissjoni mingħajr fili, eliminating the traditional spring wire connection, Tnaqqis tal-fallimenti tat-tagħmir ikkawżati minn kejbils, eliminating the disadvantages of cable dragging and oil stains, and making operation more convenient. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. Karatteristiċi tal-prodott
1. Adotta 433MHz Teknoloġija tal-Komunikazzjoni Wireless, Id-distanza ta 'operazzjoni bla fili hija 40 miters;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the same time without affecting each other;
3. Tappoġġja l-buttuna ta 'waqfien ta' emerġenza, swiċċ output tas-sinjal io, connected to the system through IO wiring;
4. Appoġġ 4 buttuni tad-dwana, Swiċċ is-sinjal IO, Sinjal tal-ħruġ għas-sistema permezz tal-protokoll IO-Link;
5. Tappoġġja l-buttuna tal-moviment malajr + u buttuna -, Agħfas u żomm il-buttuna biex tissostitwixxi l-handwheel biex tmexxi l-magna;
6. Appoġġ għall-kontroll tal-assi 6, Swiċċ is-sinjal IO, Sinjal tal-ħruġ għas-sistema permezz tal-protokoll IO-Link;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

Noti:
①Emergency stop button:
Agħfas il-buttuna ta 'waqfien ta' emerġenza, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 buttuni tad-dwana, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.

5.Dijagramma tal-Aċċessorji tal-Prodott

6.Gwida għall-Installazzjoni tal-Prodott

6.1 Product Installation Steps

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3. After the receiver is fixed, L-antenna mgħammra mar-riċevitur għandha tkun konnessa,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
Huwa rrakkomandat li tpoġġiha fuq il-parti ta 'fuq tal-kabinett elettriku għall-aħjar effett tas-sinjal. It
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4.Fl-aħħarnett, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 Dimensjonijiet ta 'installazzjoni tar-riċevitur

6.3 Dijagramma ta 'referenza tal-wajers tar-riċevitur

7. Maintenance and care

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
the service life;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. Jekk jogħġbok evita li tagħfas, jaqa ', bumping, eċċ. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. Jekk ma jintużax għal żmien twil, Jekk jogħġbok aħżen il-handwheel f'post nadif u sigur;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. Please read the instructions carefully before use. Non-professionals are prohibited from
operating.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. Jekk hija meħtieġa t-tiswija, Jekk jogħġbok ikkuntattja lill-manifattur. If the damage is caused by self-repair,
the manufacturer will not provide warranty.

]]> Wireless Electronic Handwheel DWGP https://www.wixhc.cn/product/wireless-electronic-handwheel-dwgp-instruction-manual Wed, 08 Jan 2025 08:16:31 +0000 https://www.wixhc.cn/?post_type=product&p=4608  

1.Introduzzjoni tal-Prodott

Wireless electronic handwheel is used for manual guidance, pożizzjonament, tool setting and
other operations of CNC machine tools. Dan il-prodott jadotta teknoloġija ta 'trasmissjoni mingħajr fili,
eliminating the traditional spring wire connection, Tnaqqis tal-fallimenti tat-tagħmir ikkawżati minn kejbils,
eliminating the disadvantages of cable dragging, oil stains, eċċ., and is more convenient to
operate. It is widely used in CNC machine tools such as gantry machining centers, gantry
vertical lathes, CNC gear processing machines, and can be adapted to a variety of CNC
systems on the market, bħal Siemens, Mitsubishi, FANUC, syntec and other CNC system
brands.

2.Karatteristiċi tal-prodott

1. Adotta 433MHz Teknoloġija tal-Komunikazzjoni Wireless, Id-distanza ta 'operazzjoni bla fili hija 80 miters;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the
same time without affecting each other;
3. Tappoġġja l-buttuna ta 'waqfien ta' emerġenza, and after the handwheel is turned off, the emergency stop
button is still valid;
4. Appoġġ 6 buttuni tad-dwana, swiċċ output tas-sinjal io;
5. Appoġġ għall-kontroll tal-assi 6, 7-12 Il-kontroll tal-assi jista 'jiġi personalizzat;
6. Jappoġġja 1x,10X, 100X kontroll u jista 'jkun massimu customizable 1000x;
7. Supports the enable button function, output switch l0 sianals. axis selection,maanification
and encoder.;
8. Support axis selection and magnification selection encoder output;
9. Support standard Type-C charging, 5V-2A charging specification, built-in battery specification
14500/1100mAh.

3.Speċifikazzjonijiet tal-prodott

 

4.Product function introduction

 

Noti：
①Emergency stop button：
When the emergency stop button is pressed, the two emergency stop IO outputs on
the receiver are disconnected, and all handwheel functions are invalid. When the emergency
stop is released, the emergency stop IO output on the receiver is closed, and all handwheel
functions are restored; and after the handwheel is turned off, the emergency stop IO output
of the receiver is still valid when the emergency stop button is pressed.

②Enable button:
Press any one of the enable buttons on both sides, and the two groups of enable IO
outputs on the receiver will be turned on. Release the enable button and the enable IO
output will be turned off. In addition, you need to press and hold the enable button before
switching the axis selection ratio and shaking the handwheel. This function can be
canceled through the configuration software.
③Axis selection switch (swiċċ tal-qawwa):
Press and hold the enable button and switch the axis selection switch to switch the
moving axis controlled by the handwheel. Switch this switch from OFF to any axis and
turn on the handwheel power.

④Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.

⑤Battery indicator:
The hand wheel power display, all bright means full power, all off means it is not
turned on or has no power, the first left grid flashes, indicating that the power is too low,
please charge in time.
⑥Signal Lights:
If the signal light is on, it means the handwheel is being operated and the signal is
normal; if the signal light is off, it means there is no operation, or it is being operated but
the wireless signal is not connected.

5.Dijagramma tal-Aċċessorji tal-Prodott

 

6.Gwida għall-Installazzjoni tal-Prodott

6.1 Product Installation Steps
1. Install the receiver in the electrical cabinet using the clips on the back, or install it in
the electrical cabinet using the screw holes at the four corners of the receiver.
2.Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3.After the receiver is fixed, L-antenna mgħammra mar-riċevitur għandha tkun konnessa,
and the outer end of the antenna must be installed or placed outside the electrical cabinet. It
is recommended to place it on the top of the electrical cabinet for the best signal effect. It is
forbidden to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4. Fl-aħħarnett, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 Dimensjonijiet ta 'installazzjoni tar-riċevitur

6.3 Dijagramma ta 'referenza tal-wajers tar-riċevitur

7.Product Operation Instructions
1. The machine is powered on, the receiver is powered on, the receiver working indicator
light flashes, the wireless electronic handwheel has the battery installed, the battery cover
is fastened, the wireless electronic handwheel power switch is turned on, and the
handwheel power light is on;
2. Agħżel l-assi tal-koordinati: Agħfas u żomm il-buttuna Enable, switch the axis selection
switch, and select the axis you want to operate on;
3. Agħżel ingrandiment: Agħfas u żomm il-buttuna Enable, switch the magnification switch,
and select the magnification level you need;
4. Assi li jiċċaqlaq: Agħfas u żomm il-buttuna Enable, Agħżel is-swiċċ tal-għażla tal-assi, select
the magnification switch, and then rotatethe pulse encoder to rotate the positive moving axis
clockwise and the negative moving axis counterclockwise;
5. Agħfas u żomm kwalunkwe buttuna tad-dwana, and the corresponding button IO output of the
receiver will be turned on. Release the button to turn off the output;
6. Agħfas il-buttuna ta 'waqfien ta' emerġenza, the corresponding emergency stop IO output of the
receiver is disconnected, the handwheel function is disabled, release the emergency stop
buttuna, the emergency stop IO output is closed, and the handwheel function is restored;
7. Jekk il-handwheel ma jitħaddemx għal perjodu ta 'żmien, it will automatically enter sleep
mode to reduce power consumption. Meta jerġa 'jintuża, the handwheel can be
activated by pressing the enable button;
8. Jekk il-handwheel ma jintużax għal żmien twil,it is recommended to switch the handwheel
shaft to the OFF position, Itfi l-qawwa tal-handwheel, and extend the battery life.

8.Deskrizzjoni tal-Mudell tal-Prodott

① ：DWGP represents the appearance style

② ：Parametri tal-ħruġ tal-polz:
01: Indicates that the pulse output signals are A and B, and the pulse voltage is 5V; Pulse
quantity 100PPR;
02: Indicates that the pulse output signals are A and B, and the pulse voltage is 12V; Pulse
quantity 25PPR;
03: Indicates that the pulse output signal is A B、A-、B-； Vultaġġ tal-polz 5V; Pulse quantity 1
00PPR;
04: Jindika output taċ-ċirkwit miftuħ NPN ta 'livell baxx, b'sinjali tal-ħruġ tal-polz ta 'a u b; Il
number of pulses is 100PPR;05: Jindika output tas-sors tal-PNP ta 'livell għoli, pulse output signals
are A and B; pulse quantity is 100PPR;
③ : represents the number of axis selection switches, 6 jirrappreżenta 6 assi, 7 jirrappreżenta 7 axis.
④ : represents the type of axis selection switch signal, A tirrappreżenta sinjal tal-ħruġ minn punt għal punt,
B represents encoded output signal;

⑤ : represents the type of magnification switch signal,
A tirrappreżenta sinjal tal-ħruġ minn punt għal punt, B represents encoded output signal;
⑥ : represents the number of custom buttons, 6 jirrappreżenta 6 buttuni tad-dwana;
⑦ : represents the power supply for the system handwheel, 05 jirrappreżenta 5V provvista ta 'enerġija,
u 24 represents 24V power supply.

9.Product Troubleshooting

 

10. Maintenance and care

1. Jekk jogħġbok użah f'ambjent xott f'temperatura tal-kamra u pressjoni biex testendi l-ħajja tas-servizz tagħha;
2. Jekk jogħġbok evita li tuża f'ambjenti anormali bħalma huma x-xita u l-bżieżaq tal-ilma biex testendi l-ħajja tas-servizz;
3. Jekk jogħġbok żomm id-dehra tal-handwheel nadif biex testendi l-ħajja tas-servizz tagħha;
4. Jekk jogħġbok evita li tagħfas, jaqa ', bumping, eċċ. to prevent damage to the precision components inside
the handwheel or accuracy errors;
5. Jekk ma jintużax għal żmien twil, Jekk jogħġbok aħżen il-handwheel f'post nadif u sigur;
6.Matul il-ħażna u t-trasport, attention should be paid to moisture and shock resistance.

11.Informazzjoni dwar is-sigurtà

1. Jekk jogħġbok aqra l-istruzzjonijiet bir-reqqa qabel l-użu u tipprojbixxi mhux professjonisti milli joperaw;
2. When the battery level is too low, please charge it in time to avoid errors caused by insufficient
battery and inability to operate the handwheel;

3. Jekk hija meħtieġa t-tiswija, Jekk jogħġbok ikkuntattja lill-manifattur. Jekk il-ħsara hija kkawżata minn tiswija personali, the manufacturer will not provide warranty.

]]> Mpg bla fili tat-tip imsaħħaħ – Nuqqas 12 assi https://www.wixhc.cn/product/enhanced-type-wireless-mpg-atwgp-12-axis Mon, 13 Nov 2023 08:06:21 +0000 https://www.wixhc.cn/?post_type=product&p=4453

Mudell：ATWGP-12

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, Lathes CNC, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, Lathes CNC, traveling machine tools, qtugħ u applikazzjonijiet oħra, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, Mitsubishi, FANUC, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 miters;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-assi, 8-assi, 9-assi, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, eċċ.;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. Disinn ta 'Konsum ta' Enerġija Baxxa, 2 AA batteries can be used for more than 1 month;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

 

Nota:
1. Status indicator light:
Signal light (left): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Dawl ta 'allarm ta' vultaġġ baxx (right): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.
]]> Siemens iddedikat bla fili elettroniku handwheel xwgp-et https://www.wixhc.cn/product/siemens-dedicated-wireless-electronic-handwheel-xwgp-ets Thu, 26 Mejju 2022 02:33:53 +0000 https://www.wixhc.cn/?post_type=product&p=4381

1.Introduzzjoni ta 'kontroll mill-bogħod

a.Prodott Composizzjoni
Ir-rota tal-idejn elettroniku mingħajr fili tal-wiri tal-koordinati f'ħin reali ta 'Siemens jikkonsisti f'żewġ partijiet: handwheel elettroniku + riċevitur;

b.Karatteristiċi

*Appoġġ lil Siemens plc: S7-200 / -300 / -1200；Appoġġ għall-wiri f'ħin reali ta 'valuri ta' koordinati tas-sistema Siemens；
*Id-distanza ta 'trasmissjoni bla fili hija miftuħa 40 miters, teknoloġija tal-qbiż tal-frekwenza awtomatika, jistgħu jużaw 32 settijiet ta 'tagħmir fl-istess ħin;
*Ir-rota elettronika hija mħaddma minn 2 Batteriji AA u jistgħu jintużaw għal aktar minn 30 jiem;
*Ir-riċevitur huwa mgħammar b'antenna esterna biex itejjeb is-sinjal u huwa faċli biex jiġi installat;
*Appoġġ elettroniku tar-rota tal-idejn: Encoder wieħed ta '100ppr 、Swiċċ tal-għażla tal-assi b'6 veloċitajiet 、 Swiċċ ta 'ingrandiment ta' 3 veloċitajiet;
*Appoġġ elettroniku tar-roti tal-idejn 6 buttuni tad-dwana, li jikkorrispondi għall-indirizz Siemens PLC, li jistgħu jiġu pprogrammati liberament;

*6 buttuni tad-dwana jistgħu jikkontrollaw 6 swiċċ outputs;
*L-iskrin tal-wiri juri l-valur tal-koordinati tar-reġistru korrispondenti tal-PLC f'ħin reali, and supports 6-axis display of real-time coordinates.

2.Qasam ta' applikazzjoni

Il-kontroll remot CNC programmabbli huwa użat ħafna f'diversi oqsma CNC bħal sistema ta 'inċiżjoni bil-lejżer, Magna tat-tħin CNC, Ċentru tal-magni CNC, għodda tal-magni gantry, eċċ.

3. Introduzzjoni għall-prinċipju tax-xogħol

1） Ir-rota elettronika hija konnessa ma 'PLC permezz ta' riċevitur Ethernet

a.The handwheel jittrasmetti d-data ewlenija mingħajr fili lir-riċevitur, u r-riċevitur jikteb iċ-ċwievet permezz taż-żona DB tas-sistema PLC tal-kejbil tan-netwerk; ir-riċevitur jaqra d-dejta li għandha tintwera miż-żona DB magħżula, u mbagħad jirritorna d-data lill-iskrin tal-wiri tar-rota tal-idejn. L-utent jista 'jippersonalizza l-indirizz bażi tal-qari u l-kitba taż-żona DB fuq l-handwheel, so that the handwheel can read and write the data in the DB area of the PLC.

b. Ir-riċevitur jappoġġja l-protokoll Siemens S7. Japplika għal PLC S7-200, PLC S7-300 and PLC S7-1200.

c. The user can configure the receiver to server mode and client mode through the PLC connection configuration tool.

Fil-modalità server, l-utent jikkonfigura l-indirizz tal-qari u tal-kitba tal-PLC permezz tas-softwer tal-konfigurazzjoni WGP-ETS;Uża l-għodda tal-konfigurazzjoni tal-konnessjoni PLC biex tikkonfigura r-riċevitur fil-modalità tal-klijent. Wara l-konfigurazzjoni, the XWGP-ETS receiver can communicate with the PLC through the standard S7 protocol.

2)Applikazzjoni speċifika

Applikazzjoni speċifika tar-riċevitur handwheel u Siemens PLC S7-200:

a. Il-buttuna fuq ir-rota tal-idejn tikkorrispondi mal-valur taż-żona BOOL stabbilita mill-utent fil-PLC. Jekk il-buttuna tar-rota tal-idejn tkun ippressata, iż-żona BOOL korrispondenti hija vera, u meta tiġi rilaxxata, huwa falz, u l-indirizz bażi taż-żona BOOL jista 'jiġi ssettjat permezz tar-rota tal-idejn;

b. Ir-rota tal-idejn tista 'taqra l-valur taż-żona DB fil-PLC. Assi wieħed għandu 4 bytes ta' data tal-wiri, u 6 assi għandhom total ta 24 bytes. The base address of the DB area can be set through the WGP-ETS configuration software.

4.Introduzzjoni tad-dehra

5.Definizzjoni tat-terminal tar-riċevitur u tabella tal-kodifikazzjoni

6.Daqs tad-dehra

 

 

]]> Mpg bla fili tat-tip imsaħħaħ – Assi ATWGP-8/9/10 https://www.wixhc.cn/product/enhanced-type-wireless-mpg-atwgp-8-9-10-axis Sat, 02 Apr 2022 09:02:52 +0000 https://www.wixhc.cn/?post_type=product&p=4315

Adaptation system: all CNC systems with handwheel interface

 

 

 

 

 

 

 

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, Lathes CNC, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, Lathes CNC, traveling machine tools, qtugħ u applikazzjonijiet oħra, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, Mitsubishi, FANUC, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 miters;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-assi, 8-assi, 9-assi, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, eċċ.;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. Disinn ta 'Konsum ta' Enerġija Baxxa, 2 AA batteries can be used for more than 1 month;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

Nota:
1. Status indicator light:
Signal light (left): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Dawl ta 'allarm ta' vultaġġ baxx (right): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.
]]> Handwheel bla fili msaħħa bl-e-stop ZTWGP-3 https://www.wixhc.cn/product/enhanced-wireless-handwheel-with-e-stop-ztwgp-3 Fri, 18 Feb 2022 03:13:59 +0000 https://www.wixhc.cn/?post_type=product&p=4242

]]> Manwal Wireless Enhanced Generator Pulse Handwheel Pendant ZTWGP https://www.wixhc.cn/product/enhanced-wireless-manual-pulse-generator-handwheel-pendant-ztwgp Fri, 18 Feb 2022 03:09:02 +0000 https://www.wixhc.cn/?post_type=product&p=4234

]]> Bażiku Wireless Handwheel MPG ZWGP https://www.wixhc.cn/product/basic-wireless-handwheel-mpg-zwgp Fri, 18 Feb 2022 03:02:17 +0000 https://www.wixhc.cn/?post_type=product&p=4225

]]>