Magna tas-serrieq tal-wajer tal-qtugħ awtomatiku tal-kontroll bla fili DH12S-P6s

Applikazzjoni:Użat apposta għal magna tas-serrieq tal-wajer tat-tkaxkir

1.Jappoġġja funzjoni awtomatika tal-qtugħ, automatically adjusts cutting speed according to motor current feedback

2.Distanza ta 'trasmissjoni mingħajr barrieri hija 200 miters.

3. Tappoġġja sewwieq DC.

4. Jappoġġja settings multipli tal-parametri tal-qtugħ, bħalma hi l-qtugħ tal-kurrent, Limitu tal-veloċità tal-qtugħ, eċċ.

5. Irfid li jaqleb bejn is-serrieq tal-wajer u l-modi tas-serrieq tax-xafra. Parametri tal-qtugħ differenti jistgħu jiġu ssettjati f'modi differenti.

Disinn ta 'Konsum ta' Enerġija Baxxa
Faċli biex tużah

Deskrizzjoni

1.Mudell tal-Prodott

Mudell: DH12S-P6S

Tagħmir applikabbli:wire saw/blade saw machine

2.Dijagramma tal-Aċċessorji tal-Prodott

Nota: Tista 'tagħżel waħda mit-tliet antenni. L-antenna tat-tazza tal-ġbid hija standard awtomatikament.

3.Deskrizzjoni tal-Iswiċċ tal-Kontroll mill-Bogħod

4.DisplayContent Introduzzjoni

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parametri aġġustabbli)
Automatic cutting main motor setting current: Setting: 28 (parametri aġġustabbli)
Swing arm motor speed: Swing: 0-50

Vultaġġ baxx: Il-batterija tal-kontroll mill-bogħod hija baxxa wisq, Jekk jogħġbok ibdel il-batterija.

In-netwerk naqas: Is-sinjal bla fili huwa interrott. Jekk jogħġbok iċċekkja l-qawwa tar-riċevitur, Qawwaha mill-ġdid, u terġa 'tibda l-kontroll mill-bogħod.

5.Istruzzjonijiet ta 'Operazzjoni tal-Funzjoni ta' Kontroll mill-Bogħod

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, Ixgħel is-swiċċ tal-qawwa, and the display will show the motor speed, li jindika l-istartjar ta 'suċċess.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, Dawwar “Quddiem / Reverse” Aqleb għal quddiem, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, Dawwar “Quddiem / Reverse” Aqleb għal Reverse, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Dawwar il “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, Dawwar “Quddiem / Reverse” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Dawwar “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Agħfas u żomm il “speed adjustment enable” buttuna u dawwar il - “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “Quddiem / Reverse” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (L-utenti huma pprojbiti milli jimmodifikawha mingħajr permess)

Enter the parameter menu:Fil-modalità manwali, when the main motor speed is 0, Imbotta l-iswiċċ 'il quddiem / b'lura sa tliet darbiet wara xulxin, and then push it down three times in a row to enterthe parameter menu;
Ħruġ mill-menu tal-parametru: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, default 800, unit milli second,modifika hija pprojbita;
Parametru ta 'deċellerazzjoni: Meta l-valur tal-bidla kurrenti tal-qtugħ jaqbeż dan il-valur, rapid deceleration begins, unit Ampere;
Aċċellerazzjoni A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Deċellerazzjoni A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, modifika hija pprojbita;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, modifika hija pprojbita;
Kurrent massimu: The range of main motor feedback current, unit Ampere;
Ospitanti massimu: Remote control main motor speed adjustment display range;
Mixi massimu: Invalid parameter;
Offset tal-Limitu tal-Veloċità: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Qtugħ awtomatiku, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;