Deskrizzjoni
1.Mudell tal-Prodott
Mudell: DH12S-P6S
Tagħmir applikabbli:wire saw/blade saw machine
2.Dijagramma tal-Aċċessorji tal-Prodott
Nota: Tista 'tagħżel waħda mit-tliet antenni. L-antenna tat-tazza tal-ġbid hija standard awtomatikament.
3.Deskrizzjoni tal-iswiċċ tal-kontroll mill-bogħod
4.DisplayContent Introduzzjoni
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parametri aġġustabbli)
Automatic cutting main motor setting current: Setting: 28 (parametri aġġustabbli)
Swing arm motor speed: Swing: 0-50
Vultaġġ baxx: Il-batterija tal-kontroll mill-bogħod hija baxxa wisq, Jekk jogħġbok ibdel il-batterija.
In-netwerk naqas: Is-sinjal bla fili huwa interrott. Jekk jogħġbok iċċekkja l-qawwa tar-riċevitur, Qawwaha mill-ġdid, u terġa 'tibda l-kontroll mill-bogħod.
5.Istruzzjonijiet ta 'Operazzjoni tal-Funzjoni ta' Kontroll mill-Bogħod
1）Turn on the remote control
When the receiver is powered on, Id-dawl tal-qawwa D2 fuq ir-riċevitur huwa dejjem mixgħul, u d-dawl tas-sinjal D1 jibda jteptep; Installa żewġ batteriji AA fil-kontroll mill-bogħod, Ixgħel is-swiċċ tal-qawwa, U l-wiri juri l-veloċità tal-mutur, li jindika l-istartjar ta 'suċċess.
2） Regolament kbir tal-mutur u tal-veloċità / mutur ewlieni u regolazzjoni tal-veloċità
Agħfas u żomm “Ir-regolament tal-veloċità jippermetti”, Dawwar “Quddiem / Reverse” Aqleb għal quddiem, U l-mutur ewlieni tar-riċevitur se jixgħel;
Agħfas u żomm “Ir-regolament tal-veloċità jippermetti”, Dawwar “Quddiem / Reverse” Aqleb għal Reverse, U l-mutur ewlieni tar-riċevitur se jreġġa 'lura u jixgħel;Sempliċement iċċaqlaq is-swiċċ lejn id-direzzjoni tan-nofs jew inversa, U l-mutur prinċipali jieqaf immedjatament mingħajr ma tagħfas il-buttuna li tippermetti l-kontroll tal-veloċità;Dawwar il “mutur kbir” Knob biex taġġusta l-vultaġġ tar-regolazzjoni tal-veloċità tal-inverter tal-mutur ewlieni tar-riċevitur għal 0-10V;
3） Motor li jivvjaġġa
Agħfas u żomm “Speed Adjustment Enable”, Dawwar “Quddiem / Reverse” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Dawwar “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Agħfas u żomm “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Agħfas u żomm il “speed adjustment enable” buttuna u dawwar il - “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “Quddiem / Reverse” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (L-utenti huma pprojbiti milli jimmodifikawha mingħajr permess)
Enter the parameter menu:Fil-modalità manwali, when the main motor speed is 0, Imbotta l-iswiċċ 'il quddiem / b'lura sa tliet darbiet wara xulxin, and then push it down three times in a row to enterthe parameter menu;
Ħruġ mill-menu tal-parametru: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, default 800, unit milli second,modification is prohibited;
Deceleration parameter: When the cutting current change value exceeds this value, rapid deceleration begins, unit Ampere;
Acceleration a1: When the cutting current is lower than the set cutting current, Il-valur tal-veloċità żdied b'kull aċċellerazzjoni tal-mutur tal-mixi;
Deċellerazzjoni A2: Meta l-kurrent tal-qtugħ ikun ogħla mill-kurrent tal-qtugħ tas-sett, il-valur tal-veloċità mnaqqas minn kull deċellerazzjoni tal-mutur tal-mixi;
Kurrent tad-driegħ tal-swing: Valur Default, modification is prohibited;
Ħin ta 'waqfien: Wara l-għeluq tal-mod awtomatiku ta 'tagħbija żejda kurrenti, il-kurrent jiġi skopert mill-ġdid wara perjodu ta 'żmien. Jekk huwa inqas mill-kurrent stabbilit, Il-mutur tal-mixi jibda awtomatikament; Unità t-tieni, Valur Default, modification is prohibited;
Kurrent massimu: Il-firxa tal-kurrent ewlieni tal-feedback tal-mutur, unit Ampere;
Ospitanti massimu: Kontroll mill-bogħod;
Mixi massimu: Parametru invalidu;
Offset tal-Limitu tal-Veloċità: Waqt qtugħ awtomatiku, il-kontroll tal-kontroll mill-bogħod tal-mixi tal-veloċità tal-mutur = 50% ta 'dan il-parametru;
Iżżid is-sensittività: Meta l-kurrent ewlieni tal-feedback tal-mutur jiżdied, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automatic cutting, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
6.Karatteristiċi elettriċi tal-kontroll mill-bogħod
7.Daqs tal-kontroll mill-bogħod
Id-dritt ta 'interpretazzjoni finali ta' dan il-prodott jappartjeni biss lill-kumpanija tagħna.
