दरखास्त:विशेष गरी क्रलर तारको वायर देखीको लागि प्रयोग गरिएको
1.Supports automatic cutting function, automatically adjusts cutting speed according to motor current feedback
2.ब्यारियर-नि: शुल्क प्रसारण दूरी हो 200 मिटर.
3. Support DC driver.
4. Supports multiple cutting parameter settings, such as cutting current, cutting speed limit, आदि.
5. Supports switching between wire saw and blade saw modes. Different cutting parameters can be set in different modes.
नमुना: DH12S-P6S
लागू उपकरण:wire saw/blade saw machine
स्वर: तपाईं तीन एन्टेना को एक छनौट गर्न सक्नुहुन्छ. सञ्चार कप एन्टोना डिफल्ट द्वारा मानक छ.
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(प्यारामिटरहरू समायोजन)
Automatic cutting main motor setting current: Setting: 28 (प्यारामिटरहरू समायोजन)
Swing arm motor speed: Swing: 0-50
कम भोल्टेज: रिमोट कन्ट्रोल ब्याट्री धेरै कम छ, कृपया ब्याट्री बदल्नुहोस्.
नेटवर्क खसालियो: ताररहित संकेत अवरूद्ध छ. कृपया रिसीभर को शक्ति जाँच गर्नुहोस्, यो फेरि पावर, र रिमोट कन्ट्रोल पुन: सुरु गर्नुहोस्.
1）Turn on the remote control
When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, शक्ति स्विच खोल्नुहोस्, and the display will show the motor speed, सफल स्टार्टअप सूचित गर्दै.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, घुमाऊ “अगाडि / रिभर्स” अगाडिको स्विच, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, घुमाऊ “अगाडि / रिभर्स” उल्टरमा स्विच गर्नुहोस्, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;घुमाउनुहोस् “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, घुमाऊ “अगाडि / रिभर्स” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
घुमाऊ “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
थिच्नुहोस् र समात्नुहोस् “speed adjustment enable” बटन र घुमाउनुहोस् “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “अगाडि / रिभर्स” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (प्रयोगकर्ताहरूलाई अनुमति बिना परिमार्जन गर्नबाट निषेध गरिएको छ)
Enter the parameter menu:म्यानुअल मोडमा, when the main motor speed is 0, अगाडि / उल्टो स्विच गर्नुहोस् प row ्क्तिमा तीन पटक बन्द गर्नुहोस्, and then push it down three times in a row to enterthe parameter menu;
प्यारामिटर मेनूबाट निस्कनुहोस्: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, पुरा नगर्नु 800, unit milli second,परिमार्जन निषेध गरिएको छ;
ध्वनी प्यारामिटर: जब हालको परिवर्तन मानले यस मान भन्दा बढि काट्छ, rapid deceleration begins, unit Ampere;
त्वरण A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
ध्वस्त A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, परिमार्जन निषेध गरिएको छ;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, परिमार्जन निषेध गरिएको छ;
अधिकतम हालको: The range of main motor feedback current, unit Ampere;
अधिकतम होस्ट: Remote control main motor speed adjustment display range;
अधिकतम हिंड्ने: Invalid parameter;
गति सीमा अफसेट: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: स्वचालित काट्ने, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
यस उत्पादनको अन्तिम व्याख्या भनेको हाम्रो कम्पनीमा मात्र सम्बन्धित छ.
