5.Product Function Introduction

② Enable buttons on both sides

③Button area

12 buttons

④ Axis Selection and Magnification Switch

One 9-gear axis selection switch; one 3-gear magnification switch.

⑤ Emergency Stop Switch

Remote control emergency stop switch.

⑥ Display Screen Area

It can display coordinates, status and other information.

⑦ Electronic Pulse Encoder

One electronic pulse encoder with 100 pulses per revolution.

⑧ Type-C Charging Port

It is used for connection between the charger and the remote control.

The handheld display includes a coordinate interface and a 6-point acquisition interface, which can be switched by pressing the ‘Next Page’ key

6. Product Accessories Diagram

7. Receiver and Wiring Ports

8. Configure network access

9. Test Instructions

1.Product Introduction

2.Product features

Press and hold the enable button, then toggling the axis selection switch can control the movement of axis .Press and hold the enable button, then toggle the axis selection switch to switch the motion axis controlled by the remote control. Toggle the switch from the OFF position to any axis position, and the remote control will power on automatically.

④ Pulse Encoder:

Press and hold the enable button and rotate the pulse encoder, it will output pulse signals to control the movement of the machine axis.

⑤ LCD Display Screen:

5. Product Accessories Diagram

 

6. Product Installation Guide

6.1 Product Installation Steps

1. Install the receiver in the electrical cabinet via the buckle on its back, or mount it inside the electrical cabinet through the screw holes at the four corners of the receiver.

2. Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect the equipment to the receiver with cables.

3. After the receiver is fixed in place, install the supporting antenna of the receiver properly. Mount or place the outer end of the antenna outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for optimal signal performance. Do not leave the antenna uninstalled or place it inside the electrical cabinet; otherwise, signal failure may occur.

4. Finally, turn on the remote control power switch, then you can remotely operate the machine via the remote control.

6.2 Receiver Installation Dimensions

6.3 Receiver Wiring Reference Diagram

7. Product Operation Instructions

1. Power on the machine and the receiver. The receiver operation indicator flashes. After the wireless electronic remote control is fully charged, toggle it from the OFF gear to the X-axis gear, and the remote control display lights up.

2. Select the axis : Press and hold the enable button, toggle the axis selection switch to select the axis to be operated.

3. Select the magnification: Press and hold the enable button, toggle the magnification switch to select the required magnification gear.

4. Axis movement: Press and hold the enable button, select the axis selection switch and the magnification switch, then rotate the pulse encoder. Rotate clockwise to move the axis in the positive direction, and rotate counterclockwise to move the axis in the negative direction.

5. Press and hold any custom button, the corresponding button IO output of the receiver will turn on; release the button, and the output will turn off.

6. Press the emergency stop button, the corresponding emergency stop IO output of the receiver disconnects and the remote control function becomes invalid. Release the emergency stop button, the emergency stop IO output closes and the remote control function is restored.

7. If the wireless remote control is not operated for a period of time, it will automatically enter sleep mode to reduce power consumption. It can be used normally again by pressing the enable button again.

8.If the wireless remote control is not used for a long time, turn the axis switch to OFF to turn off the power and extend battery life

8. Product Model Description

①：UWGP stands for appearance style.

②：Pulse Output Parameters：

05: Indicates high-level PNP source output, with pulse output signals of A and B; The number of pulses is 100PPR.

③：Represents the axis selection switch quantity; 6 stands for 6 axes, 7 stands for 7 axes, and so on.

④: Represents the signal type of the axis selection switch.A stands for point-to-point output signal, and B stands for encoder output signal.

⑤: Represents the signal type of the magnification switch.A stands for point-to-point output signal, and B stands for encoder output signal.

⑥: Represents the number of custom buttons; 3 corresponds to 6 custom buttons.

⑦: Represents the power supply for the system remote control. 05 stands for 5V power supply, and 24 stands for 24V power supply.

⑧: Represents the contact charging mode. It starts charging automatically when placed back on the charging base.

9. Product troubleshooting

 

10. Maintenance and upkeep

1. Please use it in a dry environment at room temperature and pressure to extend its service life.

2. Please avoid using in abnormal environments such as rain and water to extend the service life.

3. Please keep the appearance of the remote control clean to extend its service life.

4. Please avoid crushing, dropping, or bumping, etc. to prevent damage to the precision components inside the remote control or accuracy errors.

5. If not used for a long time, please store the remote control in a clean and safe place.

6. Avoid moisture and shock during storage and transportation.

1.Product Introduction

Wireless electronic handwheel is used for manual guidance, positioning, tool setting and
other operations of CNC machine tools. This product adopts wireless transmission technology,
eliminating the traditional spring wire connection, reducing equipment failures caused by cables,
eliminating the disadvantages of cable dragging, oil stains, etc., and is more convenient to
operate. It is widely used in CNC machine tools such as gantry machining centers, gantry
vertical lathes, CNC gear processing machines, and can be adapted to a variety of CNC
systems on the market, such as Siemens, Mitsubishi, Fanuc, syntec and other CNC system
brands.

2.Product features

1. Adopt 433MHZ wireless communication technology, wireless operation distance is 80 meters;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the
same time without affecting each other;
3. Support emergency stop button, and after the handwheel is turned off, the emergency stop
button is still valid;
4. Support 6 custom buttons, switch IO signal output;
5. Support 6-axis control, 7-12 axis control can be customized;
6. Supports 1X,10X, 100X control and can be maximum customizable 1000X;
7. Supports the enable button function, output switch l0 sianals. axis selection,maanification
and encoder.;
8. Support axis selection and magnification selection encoder output;
9. Support standard Type-C charging, 5V-2A charging specification, built-in battery specification
14500/1100mAh.

3.Product specifications

4.Product function introduction

Notes：
①Emergency stop button：
When the emergency stop button is pressed, the two emergency stop IO outputs on
the receiver are disconnected, and all handwheel functions are invalid. When the emergency
stop is released, the emergency stop IO output on the receiver is closed, and all handwheel
functions are restored; and after the handwheel is turned off, the emergency stop IO output
of the receiver is still valid when the emergency stop button is pressed.

②Enable button:
Press any one of the enable buttons on both sides, and the two groups of enable IO
outputs on the receiver will be turned on. Release the enable button and the enable IO
output will be turned off. In addition, you need to press and hold the enable button before
switching the axis selection ratio and shaking the handwheel. This function can be
canceled through the configuration software.
③Axis selection switch (power switch):
Press and hold the enable button and switch the axis selection switch to switch the
moving axis controlled by the handwheel. Switch this switch from OFF to any axis and
turn on the handwheel power.

④Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.

⑤Battery indicator:
The hand wheel power display, all bright means full power, all off means it is not
turned on or has no power, the first left grid flashes, indicating that the power is too low,
please charge in time.
⑥Signal Lights:
If the signal light is on, it means the handwheel is being operated and the signal is
normal; if the signal light is off, it means there is no operation, or it is being operated but
the wireless signal is not connected.

5.Product accessories diagram

6.Product Installation Guide

6.1 Product Installation Steps
1. Install the receiver in the electrical cabinet using the clips on the back, or install it in
the electrical cabinet using the screw holes at the four corners of the receiver.
2.Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3.After the receiver is fixed, the antenna equipped with the receiver must be connected,
and the outer end of the antenna must be installed or placed outside the electrical cabinet. It
is recommended to place it on the top of the electrical cabinet for the best signal effect. It is
forbidden to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4. Finally, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 Receiver installation dimensions

6.3 Receiver Wiring Reference Diagram

7.Product Operation Instructions
1. The machine is powered on, the receiver is powered on, the receiver working indicator
light flashes, the wireless electronic handwheel has the battery installed, the battery cover
is fastened, the wireless electronic handwheel power switch is turned on, and the
handwheel power light is on;
2. Select the coordinate axis: Press and hold the enable button, switch the axis selection
switch, and select the axis you want to operate on;
3. Select magnification: Press and hold the enable button, switch the magnification switch,
and select the magnification level you need;
4. Moving axis: Press and hold the enable button, select the axis selection switch, select
the magnification switch, and then rotatethe pulse encoder to rotate the positive moving axis
clockwise and the negative moving axis counterclockwise;
5. Press and hold any custom button, and the corresponding button IO output of the
receiver will be turned on. Release the button to turn off the output;
6. Press the emergency stop button, the corresponding emergency stop IO output of the
receiver is disconnected, the handwheel function is disabled, release the emergency stop
button, the emergency stop IO output is closed, and the handwheel function is restored;
7. If the handwheel is not operated for a period of time, it will automatically enter sleep
mode to reduce power consumption. When it is used again, the handwheel can be
activated by pressing the enable button;
8. If the handwheel is not used for a long time,it is recommended to switch the handwheel
shaft to the OFF position, turn off the handwheel power, and extend the battery life.

8.Product Model Description

① ：DWGP represents the appearance style

② ：Pulse output parameters:
01: Indicates that the pulse output signals are A and B, and the pulse voltage is 5V; Pulse
quantity 100PPR;
02: Indicates that the pulse output signals are A and B, and the pulse voltage is 12V; Pulse
quantity 25PPR;
03: Indicates that the pulse output signal is A B、A-、B-； Pulse voltage 5V; Pulse quantity 1
00PPR;
04: Indicates a low-level NPN open circuit output, with pulse output signals of A and B; the
number of pulses is 100PPR;05: Indicates high-level PNP source output, pulse output signals
are A and B; pulse quantity is 100PPR;
③ : represents the number of axis selection switches, 6 represents 6 axis, 7 represents 7 axis.
④ : represents the type of axis selection switch signal, A represents point-to-point output signal,
B represents encoded output signal;

⑤ : represents the type of magnification switch signal,
A represents point-to-point output signal, B represents encoded output signal;
⑥ : represents the number of custom buttons, 6 represents 6 custom buttons;
⑦ : represents the power supply for the system handwheel, 05 represents 5V power supply,
and 24 represents 24V power supply.

9.Product Troubleshooting

10. Maintenance and care

1. Please use it in a dry environment at room temperature and pressure to extend its service life;
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life;
3. Please keep the appearance of the handwheel clean to extend its service life;
4. Please avoid squeezing, falling, bumping, etc. to prevent damage to the precision components inside
the handwheel or accuracy errors;
5. If not used for a long time, please store the handwheel in a clean and safe place;
6.During storage and transportation, attention should be paid to moisture and shock resistance.

11.Safety Information

1. Please read the instructions carefully before use and prohibit non professionals from operating;
2. When the battery level is too low, please charge it in time to avoid errors caused by insufficient
battery and inability to operate the handwheel;

3. If repair is required, please contact the manufacturer. If the damage is caused by self repair, the manufacturer will not provide warranty.

1.Product Introduction

The programmable CNC remote control PHB06B is suitable for wireless
remote control operation of various CNC systems. It supports users to
customize programming and develop button functions to realize remote
control of various functions on the CNC system; it supports users to
customize programming and develop display content to realize dynamic
display of system status; the remote control comes with a rechargeable
battery and supports Type-C interface charging.

2.Product features

1. Using 433MHZ wireless communication technology, the wireless operation
distance is 80 meters;
2. Using automatic frequency hopping function, 32 sets of wireless remote
controllers can be used at the same time without affecting each other;
3. Support 12 custom button programming;
4. Support 2.8-inch screen, display content custom programming;
5. Support 1 6-speed axis selection switch, which can be custom programmed;
6. Support 1 7-speed magnification switch, which can be custom programmed;
7. Support 1 electronic handwheel, 100 pulses/turn;
8. Support standard Type-C charging; 5V-2A charging specification; battery
specification 18650/12580mWh battery.

3.Working principle

4. Product specifications

5.Product function introduction

Notes：
①Power switch：
Control hand wheel to open and close

②Enable buttons on both sides：
The enabling button must be pressed to crank the hand wheel;

③Custom button area
12 buttons arranged in 3X4, user-defined programming;

④Axis selection, magnification switch
1 6-position axis selection switch, which can be customized and programmed;
1 7-position ratio switch, which can be customized and programmed

⑤ Emergency stop switch:
Handwheel emergency stop switch;

⑥Display area:
Can display current power, signal, and customized display content;

⑦Electronic hand wheel：
1 electronic handwheel, 100 pulses/turn.

⑧Charging port:

Built-in rechargeable battery, charged using Type-C charger, charging voltage 5V,
current 1A-2A; charging time 7 hours;

6.Product accessories diagram

7.Product Installation Guide

1. Insert the USB receiver into the computer, the computer will automatically
recognize and install the USB device driver without manual installation;
2. Insert the remote control into the charger. After the battery is fully charged, turn
on the power switch, turn on the remote control, and the display shows normal, which
means the power-on is successful;
3. After powering on, you can perform any button operation. The remote control can
support dual button operation at the same time. When you press any button, a black
square will appear next to the signal on the remote control, indicating that the button
is valid.

8.Product Operation Instructions
Before product development and use, you can use the Demo software we provide to test
the buttons and display of the remote control, or use the Demo as a reference routine for
future programming development;
Before using the Demo software, please plug the USB receiver into the computer, make
sure the remote controller has sufficient power, turn on the power switch, and then use it;
When any button on the remote control is pressed, the test software Demo will display the
corresponding key value. After releasing it, the key value display disappears, indicating that
the button upload is normal.

9.Product Troubleshooting

10. Maintenance and care

1. Please use it in a dry environment with normal temperature and pressure to extend
the service life;
2. Do not use sharp objects to touch the key area to extend the service life of the key;
3. Please keep the key area clean to reduce key wear;
4. Avoid squeezing and falling to cause damage to the remote control;
5. If not used for a long time, please remove the battery and store the remote control and
battery in a clean and safe place;
6. Pay attention to moisture-proof during storage and transportation.

11.Safety Information

1. Please read the instructions carefully before use. Non-professionals are prohibited
from operating.
2. Please use the original charger or a charger produced by a regular manufacturer with
the same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing
the remote control to be unresponsive.
4. If repair is required, please contact the manufacturer. If the damage is caused by
self-repair, the manufacturer will not provide warranty.

1.Product Introduction

The programmable CNC remote control PHB10 is suitable for wireless
remote control operation of various CNC systems. It supports user-defined
programming to develop button functions, and realize remote control of various
functions on the CNC system; it supports user-defined programming to develop
LED lights to light up and turn off, and realize dynamic display of system status;
the remote control comes with a rechargeable battery and supports Type-C
interface charging.

2.Product features

1. Using 433MHZ wireless communication technology, the wireless operation
distance is 80 meters;
2.Using automatic frequency hopping function, 32 sets of wireless remote
controllers can be used at the same time without affecting each other;
3.Support 32 custom button programming;
4.Support 9 custom LED light display programming;
5.Support IP67 waterproof level;
6.Support standard Type-C interface charging; 5V-2A charging specification;
1100 mAh large capacity battery, with automatic sleep standby function; realize
ultra-long low power standby;
7.Support real-time display of power.

3.Working principle

4. Product specifications

5.Product function introduction

Notes：
①Battery level display：
Lights up after power on, turns off after power off;
If the battery indicator light is only one bar and keeps flashing, it means the
battery is too low. Please replace the battery;

If the battery indicator lights are all on and the other LED lights flash back and
forth, it means the battery is very low. Please replace the battery;
If the battery indicator does not light up or go out, and the device cannot be
started by pressing and holding the power button, please replace the battery;

②Button area：32 buttons arranged in 4X8, user-defined programming;

③Status LED：
COMMU: Button indicator light, lights up when the button is pressed and goes
out when the button is released; other lights are custom displays;

④Power switch：
Long press for 3 seconds to turn on, long press for 3 seconds to turn off;
⑤Charging port：
Use Type-C charger to charge, charging voltage 5V, current 1A-2A; charging
time 3-5 hours;

When charging, the power indicator flashes, indicating that it is charging. When
fully charged, the power indicator will show full bar without flashing.

6.Product accessories diagram

7.Product Installation Guide

1 . I nsert the USB receiver into the computer, the computer will automatically
recognize and install the USB device driver without manual
2. Insert the remote control into the charger. After the battery is fully charged, press
and hold the power button for 3 seconds. The remote control will turn on and the power
indicator will light up, indicating that the power-on is successful.
3. After powering on, you can perform any button operation. The remote control
can support dual button operation at the same time. When you press any button, the
COMMU light on the remote control will light up, indicating that this button is valid.

8.Product Operation Instructions
Before product development and use, you can use the demo software we provide to
test the buttons on the remote control and the LED light on the remote control. You can
also use the demo as a reference routine for future programming development.
Before using the Demo software, please plug the USB receiver into the computer,
make sure the remote controller has sufficient power, press and hold the power button to t
urn it on, and then use it;
When any button on the remote control is pressed, the test software demo will display
the corresponding key value. After releasing it, the key value display disappears,
indicating that the key upload is normal;
You can also select the LED light number on the test software demo, click download,
and the corresponding light number on the remote control will light up, indicating that the
LED light is downloading normally.

9.Product Troubleshooting

10. Maintenance and care

1. Please use it in a dry environment with normal temperature and pressure to extend
the service life;
2. Do not use sharp objects to touch the key area to extend the service life of the key;
3. Please keep the key area clean to reduce key wear;
4. Avoid squeezing and falling to cause damage to the remote control;
5. If not used for a long time, please remove the battery and store the remote control
and battery in a clean and safe place;
6. Pay attention to moisture-proof during storage and transportation.

11.Safety Information

1. Please read the instructions carefully before use. Non-professionals are prohibited from
operating.
2. Please use the original charger or a charger produced by a regular manufacturer with the
same specifications.
3. Please charge in time to avoid incorrect operation due to insufficient power causing the
remote control to be unresponsive.
4. If repair is required, please contact the manufacturer. If the damage is caused by self-repair,
the manufacturer will not provide warranty.