Bezdrôtové elektronické ručné koleso vyhradené pre FANUC

Opis

1.Úvod výrobkov

Wireless electronic handwheel is used for manual guidance, polohovanie, zarovnanie nástroja,a ďalšie operácie na CNC obrábacích strojoch. Tento produkt využíva technológiu bezdrôtového prenosu, eliminating the traditional spring wire connection, zníženie porúch zariadení spôsobených káblami, eliminating the disadvantages of cable dragging and oil stains, a zjednodušiť prevádzku. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,zväčšenie, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. Vlastnosti produktu
1. Prijať bezdrôtovú komunikačnú technológiu 433 MHz, Vzdialenosť bezdrôtovej prevádzky je 40 meracie výrobky;
2. Prijať funkciu automatického frekvencie, využitie 32 sets of wireless remote controllers at the same time without affecting each other;
3. Podporujte tlačidlo núdzového zastavenia, prepnúť výstup signálu IO, connected to the system through IO wiring;
4. Podporovať 4 vlastné tlačidlá, prepínač IO signálu, výstupný signál do systému cez protokol IO-LINK;
5. Podpora tlačidla rýchleho pohybu + a tlačidlo -, stlačte a podržte tlačidlo, aby ste vymenili ručné koleso, aby ste mohli pohybovať strojom;
6. Podpora 6-osového ovládania, prepínač IO signálu, výstupný signál do systému cez protokol IO-LINK;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Podpora pulzného kodéra, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

Poznámky:
①Emergency stop button:
Stlačte tlačidlo núdzového zastavenia, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 vlastné tlačidlá, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.

5.Diagram príslušenstva výrobkov

6.Sprievodca inštaláciou produktu

6.1 Kroky inštalácie produktu

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Pozrite sa na náš diagram zapojenia prijímača, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3. Po opravení prijímača, Anténa vybavená prijímačom musí byť pripojená,
a vonkajší koniec antény musí byť nainštalovaný alebo umiestnený mimo elektrickej skrinky.
Odporúča sa umiestniť na hornú časť elektrickej skrinky pre najlepší signálny efekt. It
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4.Konečne, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.

6.2 Rozmery inštalácie prijímača

6.3 Referenčná schéma zapojenia prijímača

7. Údržba a starostlivosť

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
životnosť;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. Vyhnite sa stláčaniu, padajúce, narážanie, tam. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. Ak sa nepoužíva dlho, uložte ručné koleso na čisté a bezpečné miesto;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. Pred použitím si pozorne prečítajte pokyny. Non-professionals are prohibited from
operating.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. Ak sa vyžaduje oprava, Kontaktujte výrobcu. If the damage is caused by self-repair,
Výrobca nebude poskytovať záruku.