Crawler Wire Saw Machine samodejno brezžično daljinsko upravljanje DH12S-LD

Opis

Model izdelka

Model: DH12S-LD

Uporabna oprema:crawler wire saw machine

Diagram dodatkov za izdelke

Opomba: Izberete lahko eno izmed treh anten. Prisesna antena je privzeto standardna.

Opis stikala za daljinsko upravljanje

Predstavitev vsebine zaslona

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parametri nastavljivi)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Nizka napetost: Baterija daljinskega upravljalnika je prenizka, prosim zamenjajte baterijo.

Omrežje je padlo: Brezžični signal je prekinjen. Preverite moč sprejemnika, znova vklopite, in znova zaženite daljinski upravljalnik.

Navodila za delovanje funkcije daljinskega upravljalnika

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Vklopite stikalo za vklop, andthe display will show the motor speed, kar pomeni uspešen zagon.

2.Large motor and speed regulation

Obrnite “naprej/nazaj” preklopite naprej, the receiver’s large motor will turn on, and the display will show forward

Obrnite “naprej/nazaj” preklopite v vzvratno vožnjo, the large motor of the receiver will turn on in reverse, and the display will show reverse

Zavrtite “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “naprej/nazaj” preklopite naprej, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Obrnite “Naprej/nazaj” preklopite v vzvratno vožnjo, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Obrnite “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Obrnite “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

V ročnem načinu:
Turn left in place: Pritisnite in držite “Enable” button, obrnite “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Pritisnite in držite “Enable” button, obrnite “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

V samodejnem načinu: press and hold the “Enable” gumb in zavrtite “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.Samodejno rezanje

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: V ročnem načinu, press and hold the “Enable” gumb in zavrtite “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 do 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (uporabnikom je prepovedano spreminjati brez dovoljenja)

Nekatere funkcije daljinskega upravljalnika je mogoče prilagoditi s parametri. V ročnem načinu, when the small motor speed S2 is 10, trikrat zaporedoma potisnite stikalo naprej/nazaj navzgor, and then push it down three times in a row to enter the parameter menu;
Zapustite meni parametrov: izberite shranjevanje ali ne shranjevanje, then press the enable button to confirm the exit;
Največji tok: the operating rated current of the cutting motor is 80% of this currentt;
Parametri za nadzor hitrosti: automatic cutting control parameters, privzeto 800, spreminjanje je prepovedano;
Parameter upočasnitve: automatic cutting control parameter. Ko vrednost spremembe rezalnega toka preseže to vrednost,deceleration begins.
Pospešek A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Pojemka A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Začnite samoopisovanje: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Največja hoja: the maximum speed of the small motor.
Rezalni tok: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Privzeta omejitev hitrosti: the default maximum speed of automatic cutting speed when turning on the machine.
Samodejni način: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Omejitev hitrosti odmik: the maximum speed of the small motor during automatic cutting.
Največji gostitelj: maximum speed of large motor.

Električne značilnosti daljinskega upravljalnika

Velikost daljinskega upravljalnika

Pravica do končne razlage tega izdelka pripada samo našemu podjetju.