Kawat ragaji mesin motong otomatis nirkabel kadali jauh DH12S-P6S

Aplikasi:Khusus dipaké pikeun mesin ragaji kawat crawler

1.Supports automatic cutting function, automatically adjusts cutting speed according to motor current feedback

2.Jarak transmisi bébas panghalang téh 200 méter.

3. Support DC driver.

4. Supports multiple cutting parameter settings, such as cutting current, cutting speed limit, jsb.

5. Supports switching between wire saw and blade saw modes. Different cutting parameters can be set in different modes.

Desain konsumsi kakuatan low
Gampang dianggo

Katerangan

1.Modél produk

Modél: DH12S-P6S

Peralatan anu berlaku:wire saw/blade saw machine

2.Diages aksés produk

Catetan: Anjeun tiasa milih salah sahiji tina tilu antena. Antena nyeuseup cups nyaéta standar sacara standar.

3.Katerangan Kontrak Red

4.Bubuka pintonan

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parameter)
Automatic cutting main motor setting current: Setting: 28 (parameter)
Swing arm motor speed: Swing: 0-50

tegangan low: Batré kadali jauh lemah teuing, mangga gentos batréna.

Jaringan turun: Sinyal nirkabel diganggu. Mangga parios kakuatan panarima, hurungkeun deui, jeung balikan deui kadali jauh.

5.parentah operasi fungsi kadali jauh

1）Turn on the remote control

Nalika panarima dihurungkeun, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install dua accu AA dina kadali jauh, ngahurungkeun switch kakuatan, and the display will show the motor speed, Nunjukkeun ngamimitian anu suksés.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, péngkolan “Maju / sabalikna” switch maju, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, péngkolan “Maju / sabalikna” switch ka sabalikna, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Muterkeun “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, péngkolan “Maju / sabalikna” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Péngkolan “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Pencét sareng tahan “speed adjustment enable” tombol sareng muterkeun “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “maju / sabalikna” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (Pangguna dilarang tina ngarobih deui tanpa ijin)

Enter the parameter menu:Dina modeu manual, when the main motor speed is 0, nyorong maju / sabalikna ngalih tilu kali sakaligus, and then push it down three times in a row to enterthe parameter menu;
Kaluar ménu parameter: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, dituna 800, unit milli second,modifikasi dilarang;
Parameter dekilasi: When the cutting current change value exceeds this value, rapid deceleration begins, unit Ampere;
Acceleration a1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Deceleration a2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, modifikasi dilarang;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, modifikasi dilarang;
Ayeuna: The range of main motor feedback current, unit Ampere;
Maximum host: Remote control main motor speed adjustment display range;
Maximum walking: Invalid parameter;
Speed limit offset: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Motong otomatis, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;