Чыбык машинасын автоматик кисү дру белән дистанцион контроль DH12S-P6s

Тасвирлау

1.Продукция моделе

Модель: DH12S-P6S

Кулланыла торган җиһаз:wire saw/blade saw machine

2.Продукт аксессуары схемасы

Искәрмә: Сез өч антенналарны сайлый аласыз. Сору кубогы Антенна килешү буенча стандарт.

3.Дистанцион контроль ачкыч тасвирламасы

4.Dispontent кереш сүз

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(Параметрлар көйләнә)
Automatic cutting main motor setting current: Setting: 28 (Параметрлар көйләнә)
Swing arm motor speed: Swing: 0-50

Түбән көчәнеш: Дистанцион контроль батарея бик түбән, Зинһар, батареяны алыштырыгыз.

Челтәр ташланды: Чыбыксыз сигнал өзелә. Зинһар, кабул итүче көчен тикшерегез, Аны яңадан эшләгез, һәм дистанцион контрольне яңадан эшләтеп җибәрегез.

5.Дистанцион контроль функциясе операциясе

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, Энергия ачкычын кабызыгыз, and the display will show the motor speed, уңышлы стартапны күрсәтә.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, борыгыз “Алга / кире” Алга күчү, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, борыгыз “Алга / кире” кире, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Әйләндерү “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, борыгыз “Алга / кире” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Борыгыз “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” күчү, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Басыгыз һәм тотыгыз “speed adjustment enable” төймә һәм әйләнү “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “алга / кире” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (Кулланучылар аны рөхсәтсез үзгәртү тыела)

Enter the parameter menu:Кул белән режимда, when the main motor speed is 0, алга / кире әйләнүне өч тапкыр әйләндерегез, and then push it down three times in a row to enterthe parameter menu;
Параметр менюсыннан чык: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, Килешү 800, unit milli second,модификация тыела;
Чыннанрак параметр: Заманча үзгәрү кыйммәте бу кыйммәттән артканда, rapid deceleration begins, unit Ampere;
Тизләнү A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Тизләнү A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, модификация тыела;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, модификация тыела;
Максималь ток: The range of main motor feedback current, unit Ampere;
Максималь хуҗа: Remote control main motor speed adjustment display range;
Максималь йөрү: Invalid parameter;
Тизлек чикләме: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Автоматик кисү, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;берәмлек: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Дистанцион контроль электр характеристикалары

7.Дистанцион контроль зурлыгы

Бу продуктның соңгы аңлатмасы безнең компаниягә генә тиеш.