CNC вертикаль Лейт операцияләре өчен CNC вертикаль Лейт өчен махсус чыбыксыз ерак

① Pulse encoder:
Эшне кушыгыз һәм тотыгыз, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Түбән көчәнеш сигнализациясе, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Ашыгыч тукталыш төймәсенә басыгыз, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (Энергия ачкычы):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, кабул итүче белән җиһазландырылган антенна тоташырга тиеш, and the outer end of the antenna should be installed or placed outside the electrical cabinet. Аны электрик Министрлык башында иң яхшы сигнал эффектына урнаштырырга киңәш ителә. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Ниһаять, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Алып алу үлчәмнәре

6.3 Кабул итүче белгечлек схемасы

7. Продукция операциясе күрсәтмәләре
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, һәм
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Координатаны сайлагыз: Эшне кушыгыз һәм тотыгыз, toggle the axis selection switch, and select the axis you want to operate.
3. Зурайтуны сайлагыз: Эшне кушыгыз һәм тотыгыз, toggle the magnification switch,and select the desired magnification level.
4. Күчерү: Эшне кушыгыз һәм тотыгыз, Axis сайлау ачкычын сайлагыз, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Теләсә нинди махсус төймәгә басыгыз һәм үткәрегез, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Ашыгыч тукталыш төймәсенә басыгыз, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. Әгәр дә кул эше берникадәр вакыт эшләмәсә, it will automatically enter sleep mode to reduce power consumption. Кабат кулланыла, the handwheel can be activated by pressing the enable button.
8. Әгәр дә кул эше озак кулланылмаса, it is recommended to switch the handwheel shaft to the OFF position, Кул белән сүндерелгән көчен сүндер, һәм батарея гомерен озайп.

8. Продукция моделе тасвирлау

① :ZTWGP represents the appearance style
②：Пулса 6 параметрлар:
01: Indicates that the pulse output signal is A, B; Pulse көчәнеш 5В; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Pulse көчәнеш 5В; pulse quantity 100PPR.
04：Түбән дәрәҗәдәге NPN ачык схеманы күрсәтә, А һәм В пульс чыгару сигналлары белән;The number of pulses is 100PPR.
05：Югары дәрәҗәдәге PNP чыганак чыганакларын күрсәтә, А һәм В пульс чыгару сигналлары белән; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 күрсәтә 2 axes.
④：Represents the type of axis selection switch signal, А ноктасын ачу күрсәтү сигналын күрсәтә, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, А ноктасын ачу күрсәтү сигналын күрсәтә, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 күрсәтә 2 махсус төймәләр.
⑦：Represents the power supply for the system handwheel, һәм 05 5В электр белән тәэмин итүне күрсәтә.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions