Trekli avtomashinadagi arqonni avtomatik kesish uchun masofadan boshqarish arqonni ko'rishga mos keladi
Kesish mashinalari. U ishlatiladi 485 Chap va to'g'ri yo'l chastotasini boshqarish uchun Modbus Rtu Protokol
konvertorlar, shuningdek, katta motor chastotasini konvertatsiya qilish tezligi va old tomoni, orqa,
Chap va to'g'ri yo'nalishi kontroller. Va u katta vosita chastotasining ish oqimini o'qishi mumkin
orqali konvertor 485 Modbus Rtu Protokol. Oqimni tahlil qilish va taqqoslash orqali
katta motor, Chap va to'g'ri yo'llarning tezligi real vaqt rejimida avtomatik ravishda sozlanishi mumkin
achieve automatic cutting function.

2. Mahsulot funktsional xususiyatlari

1. 433mhz simsiz aloqa texnologiyasini qabul qilish, simsiz operatsiya masofasi bilan 100 meters.
2. Avtomatik chastotalarni o'chirish funktsiyalarini qabul qiling va foydalaning 32 simsiz masofadan boshqarish moslamasining to'plamlari
bir vaqtning o'zida, without affecting each other.
3. Barcha chastotani konvertorlarni qo'llab-quvvatlaydi 485 Modbus Rtu Protokol, va hozirda mos chastota
Konverter brendlari kiradi:Shanxay Xielin, Fuji, Huichuan, Zhonongen, Inlamoq, va . Brendlar uchun
Bu mos kelmaydi, please contact us for customization.
4. Tezlikni tartibga solishni qo'llab-quvvatlash, boshlamoq, and current reading of large motor frequency converters.
5. Chap va to'g'ri yo'lni tez chastotali konvertatsiya qilish, boshlamoq, old, orqaga qaytish, left and right control.
6. Mashinani a ichida yurishni davom ettirish uchun chap va o'ng qanot chastotalarini o'zgartiradigan chiziqli tuzatuvchini qo'llab-quvvatlang
straight line.
7. Arqonning avtomatik kesish funktsiyasini qo'llab-quvvatlang, Chap va to'g'ri yo'lning tezligini avtomatik ravishda sozlang
real time according to the current information of the large motor.
8. Bundan tashqari, avtoulovni boshlash va to'xtatish uchun IO chiqish boshqarmasi bilan mos keladi, va analog kuchlanish chiqishi
control for motor speed.

3. Mahsulot xususiyatlari

4. Mahsulot funktsiyasi Kirish

Qaydlar:
අscreen displey:

②Mode tugmasi:

Yassi:
Kombinatsiya tugmachalari, Ba'zi operatsiyalar ishlash uchun yoqilgan tugmachani ushlab qolishni talab qiladi,see the instructions for each switch for details.
Motorli motorli almashtirish:
3 tezlikda tiklash tugmachasini ishlatish, Ushbu kalitni tortib olish katta motorning oldinga va teskari aylanishini boshqarishi mumkin. Uni bo'shatgandan keyin, davlat qoladi, va ekranda tegishli displeylar bo'ladi. S1 , and the S1 ↓ arrow indicates everse rotation.
⑤SMall dvigatelni oldinga / teskari almashtirish:
Kichik motor uning oldida 3 tezlikda o'z-o'zini qulflash tugmachasi bilan jihozlangan. Yoqish tugmachasini bosib, ushbu kalitni tortish, oldinga va orqaga o'tish uchun kichik motorni boshqarishi mumkin, va mos keladigan displey ekranda paydo bo'ladi.  O'q oldinga, and the ↓↓ arrow represents backward.
 To'g'ri chiziqni tuzatish:
Multi-licod dastasini ishlatish, Yoqish tugmachasini bosing, tugmachani o'ng tomonga burang, va to'g'ri chiziq tuzatishni namoyish eting: Df: Chap burilgan tugmachalar ko'payadi 1 aylantirish uchun birlik, va chap
motor tezligi oshadi 0.1 birlik; Chap tugmachasini burang, to'g'ri chiziqni tuzatish: Df: O'ngda, Townning har bir burilish ko'payadi 1 birlik, va o'ng motorning tezligi oshadi
bilan 0.1 unit.
⑦Mall Motop:
3 tezlikda tiklash tugmachasini ishlatish, Qo'lda ishlaydiganida, Chap yoki o'ngga burilish uchun kichik motorni boshqarish mumkin. Bir marta chiqarilgan, Masofadan boshqarish pult avtomatik ravishda ushbu harakatni to'xtatadi. Oldinda holatda, Ushbu kalitga aylantirilganda, Tegishli displey ekranda paydo bo'ladi. ← ↑ o'q chap burilishni ko'rsatadi, va ↑ → → → o'q to'g'ri o'zgarishni anglatadi., Ushbu kalitni yoqing va ekranda tegishli displey paydo bo'ladi. ← ↓ o'q chap burilishni ko'rsatadi, and the ↓→ arrow indicates right turn.
⑧ Katta motor tezligini tartibga solish:
Multi-licod dastasini ishlatish, aylanish 1 har safar panjara, katta motor o'zgarishi tezligi taxminan 0.2 birliklar. Fast rotation can quickly modify the speed value of the large motor.
⑨ Kichik motor tezligini tartibga solish:
Multi-licod dastasini ishlatish, Qo'l rejimida, Yoqish tugmachasini bosing va keyin bir vaqtning o'zida bitta panjarani aylantiring，Chap va o'ngdagi kichik motorlarning tezligi o'zgarishi 0.1 birliklar, va tez aylanish kichik motor.in avtomatik rejimning tezligini tezda o'zgartirishi mumkin, Yoqish tugmachasini bosing va bir vaqtning o'zida bitta panjarani aylantiring,Tezlik chegarasi - bu kichik motor o'zgarishi qiymati taxminan 0.1 birliklar. Rapid rotation can quickly modify the speed limit value of the small motor.
⑩ Masofadan boshqarish pulti
The remote control display screen is turned on.

5. Mahsulotning qo'shimcha diagrammasi

6. Mahsulotni o'rnatish bo'yicha qo'llanma
6.1 Mahsulotni o'rnatish bosqichlari
1. Qabul qilgichni orqa tomondan tutqich orqali elektr kabinetiga o'rnating, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Qabul qiluvchiimiz sigrammasiga murojaat qiling va uni saytdagi uskunalar bilan taqqoslang. Connect the equipment to the receiver through wires.
3. Qabul qilgichni tuzatgandan so'ng, Qabul qilgich bilan jihozlangan antennani ulash va antennaning tashqi uchini elektr kabinetidan tashqarida o'rnatish kerak. Uni eng yaxshi signal effektiga elektron kabinetning yuqori qismida joylashtirish tavsiya etiladi. Antennadan uchraydigan yoki uni elektr kabinetida qoldirish taqiqlanadi, as it may cause the signal to be unusable.
4. Nihoyat, Masofadan boshqarish pultidagi batareyani o'rnating, Batareya qopqog'ini torting, va masofadan boshqarish pultining elektr tugmachasini yoqing. Masofadan boshqarish pultidan keyin displey ekran normal holatni ko'rsatadi
Ishchi interfeys, remote control operations can be performed.

6.2 Qabul qiluvchilarni o'rnatish o'lchamlari

6.3 Qabul qiluvchining sxemasi

7. Mahsulotni ishlatish bo'yicha ko'rsatmalar
7.1 Masofadan boshqarish pulti parametr sozlamalari
Masofadan boshqarish pultini qo'lni olish usuli:

Mode tugmachasini qo'lda rejimiga aylantiring, kichik motor tezligini sozlang 25 ikkala tomonda, yoki 0, 10, 20, 40, 50 har tomondan, va doimiy ravishda katta motorni oldinga siljiting 3 vaqt va pastga 3 vaqt;
Dan foydalaning “Kichik motor tezligini boshqarish” Sahifalarni siljitish uchun tugmachalar, Yoqish tugmachasini bosing, va parametrlarni o'zgartirish uchun kichik motor tezligini boshqarish dastasini burang. Modlashtirishdan keyin, sahifani oxirigacha aylantiring,tanlamoq “Tejash” Chiqish uchun, va menyudan chiqish uchun yoqish tugmachasini bosing;
Parametrlar quyidagicha:
Maksimal oqim: Katta motor oqimining aloqa doirasi, 15-200A diapazoni, bajarilish 100;
Tezlikni boshqarish parametrlari: Avtomatik rejim, kichik motor avtomatik tezroq yoki sekinroq tezlashtiradi,tezroq kichikroq, O'rnatish oralig'i 200-1500, bajarilish 800;
Dreatsion parametr: Motor tezligini o'zgartirishga imkon beradigan yuqori chegarani o'rnating. Ushbu qiymatdan tashqari joriy o'zgarishlar qachon, sekinlashuv paydo bo'ladi. Kichikroq, chap va o'ng motorlarning sekinlashishi tezroq, qator bilan 05-12 va odatiy 06;
A1 ni tezlashtirish: Motor tezligi kattaroq, tezroq ko'payadi, qator bilan 00-06 va odatiy 01;
A2 ni sekinlashtirish: Motor tezligi kattaroq, tezroq kamayadi, qator bilan 00-06 va odatiy 02;
Tezlikni tartibga solishni yoqish: Kichik motor tezligini tartibga solish kerakmi?? 00 yoqmaydi, 01 imkoniyat, sukut 01;
O'z-o'zini qulflashni boshlang: Oldinga va teskari kalitlar chiqargandan so'ng katta motorni avtomatik ravishda ushlab turadimi?? 00 ushlab turmaydi, 01 ushlab turadi, default 01
Maksimal yurish: chap va o'ng motorlarning maksimal tezligi, oraliq 10-100, bajarilish 50;
Oqim kesish: Maksimal kesish oqimi, ekranda IC qiymati sifatida ko'rsatilgan, oraliq 15-160, default 30,
IC-ga mos keladigan: 30 ekranda ko'rsatiladi. Ushbu parametrning yuqori chegarasi 80% maksimal oqim;
Standart tezlik chegarasi: Standart kichik motorli avtomatik avtomatik kesish tezligi doirasida 0-100, odatiy hol bilan 10. Ekran f1.0 displeylari, and this parameter is only accurate when the maximum walking is set to 50.
Avtomatik rejim: Ga o'rnatilgan 00, Avtomatik / qo'lda kalit - bu rejim almashtirish. Ga o'rnatilgan 01, Avtomatik / qo'l almashinuvi avtomatik pozitsiyaga o'rnatiladi, displey ekran yoritish ko'rsatadi, va qabul qilgichda avtomatik terminalni chiqarish yopiq. Qo'llanmaga o'rnatilganda, Avtomatik chiqish terminali uzilgan;
Tezlik chegarasi og'ish: Kichik motorning avtomatik kesish tezligining yuqori chegarasi ushbudan boshlab: 00 ga 200, odatiy hol bilan 60 va mos keladigan displey 6.0 ekranda; Displey qiymatining yuqori chegarasi = Tezlik chegarasi qoplash x 0.1;
Maksimal xost: katta motorning maksimal tezligi, oraliq 10-100, bajarilish 50;
Mbus uskunalari (majburiy): Katta motor chastotasi konvertori modelini tanlash, oraliq 00-03, bajarilish 03;
00- Shanxay Xielin 01-Fuji
02-03-Koldence (Zhonchen), Robichon)
SBUS uskunalari (majburiy): Kichik vosita chastotasi modelini tanlash, oraliq 00-05, bajarilish 03;

00- Shanxay Xielin 01-Fuji
02-03-Koldence (Zhonchen), Robichon)

04-Anchuanda 05-yo'q

7.2 Chastota konvertorini parametr sozlamalari
1. Buyruq manbai tanlovi: Aloqa buyrug'i kanali
2. Asosiy chastotali manbani tanlash: Aloqa berilgan
3. Bold stavkasi: 19200
4. Ma'lumot formati: Tekshirish yo'q, Ma'lumot formati<8-N-1>
5. Mahalliy manzil: Chap chastota konvertasini o'rnating 1, to'g'ri chastota konvertori 2, va
the large motor frequency converter to 3
7.3 Masofadan boshqarish pulti bo'yicha ko'rsatmalar
1. Mashinada quvvat, Masofadan boshqarish pultini yoqing, Masofadan boshqarish pultini bosing, sozlash
Masofadan boshqarish pulti Orqaga ega parametrlar, asosan kichik motor va katta motor chastotasini o'rnatish
Konverter modellari: (Agar mashinani ishlab chiqaruvchi uni o'rnatgan bo'lsa, ushbu qadamni o'tkazing);
2. Chastota konvertori parametrlarini o'rnating (Agar mashina ishlab chiqaruvchisi bo'lsa, ushbu qadamni o'tkazib yuboring
allaqachon o'rnatgan);
3. Masofadan boshqarish pultini qo'lda sozlash, va keyin mashinani siljitish uchun masofadan boshqarish pultidan foydalaning
ish joyi;
4. Qo'l rejimida, katta motorning kesish oqimini IC-ga va katta motor tezligini o'rnating
5. Avtomatik rejimga o'tish va kichik dvigatel uchun kesish tezligini kamaytirish f;
6. Avtomatik rejimda, Katta motorni boshlash uchun katta motorli kalitni oldinga burang, keyin buriling
Oldinga yoki teskari tomonga kichik motorli kalit, va masofadan boshqarish pultini avtomatik kesib oladi
mode to start cutting.

8.Mahsulotni bartaraf etish

9.Parvarishlash
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the battery compartment and metal shrapnel area clean.
4. Please avoid damaging the remote control due to squeezing and falling.
5. Agar uzoq vaqt ishlatilmasa, Iltimos, batareyani chiqarib oling va masofadan boshqarish pulti va batareyani toza holda saqlang
and safe place.
6.Saqlash va tashish paytida, attention should be paid to moisture and shock resistance.

10. Xavfsizlik haqida ma'lumot
1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Iltimos, batareyani o'z vaqtida joylashtiring, chunki batareyani o'z vaqtida almashtiring
etarli emas, which may result in the remote control being unable to operate.
3. Agar ta'mirlash talab qilinsa, Iltimos, ishlab chiqaruvchi bilan bog'laning. Agar zarar o'z-o'zini ta'mirlash natijasida yuzaga kelsa, Ishlab chiqaruvchi
will not provide warranty.

Model: DH01R-4W-26K

Qo'llaniladigan uskunalar:various industrial equipment

2.Mahsulot uchun aksessuarlar diagrammasi

Eslatma: Siz uchta antennalardan birini tanlashingiz mumkin. The suction cup antenna is standard by default.

3.Product model description

Eslatma:
① DH01R series, if the suffix contains T, it means with emergency stop output;without T, it means without emergency stop output.

②If there is no analog output, there is no need to remark 0W or 0R; the analogquantities W1, W2, W3, and W4 default to 0-10V analog voltage output; at the same time, W1 and W2 can be expanded to 2 isolated digital potentiometer outputs, qator bilan 0 -5K ohms, ½ watt; resolution: 20 ohms. The two digital potentials can be used to control the welding current and welding voltage of the welding machine. If the digital potentiometer output is required, user notes are required.

④Analog input, ranging from 1 ga 2, indicating that there are 1 ga 2 analog Kirish(maximum 2 kanallar); when there is an analog input, you need to note the voltage range of the analog input (our receiver defaults to 0 -5Voyaga yettirmoq, the user can also note as 4-20 mA or 0-10V, va hokazo.) and the corresponding display range of the analog quantity (for example: display 0-100 volts or 0-1000 amps)

These two analog quantities can be used as displays for welding current and welding voltage.

4.Xususiyatlari

1）Maximum 26 o'rni chiqadi;
2）Maximum 4 Analogning kanallari 0-10V chiqishi (Displey oralig'ini sozlash mumkin): Qo'llab-quvvatlaydi 2 Kengaytirilgan izolyatsiya qilingan raqamli potentsiometr chiqindilari kanallari;
3）2 analog inputs; va masofadan boshqarish pultida ko'rsatiladi, displey diapazoni sozlash mumkin
4）1 channels of emergency stop relay output normally closed contacts;
5） Powered by 3 Aa batareyalari, low power consumption design;
6） Wireless operation distance is 200 metr;
7）Protection grade IP67;
8）With cross switch operation, supports two 4-direction cross switches;
9）Back strap design.

5.Masofadan boshqarish pulti Tasvir tavsifi

6.Display content introduction

W1 knob value: W1: 0-1000 (parameter adjustable 0-9999)
W2 knob value: W2: 0-5000 (parameter adjustable 0-9999)
W3 knob value: W3: 0-5000 (parameter adjustable 0-9999)
W4 knob value: W4: 0-5000 (parameter adjustable 0-9999)
ADC1 feedback display: 0-1000 (parameter adjustable 0-5000)
ADC2 feedback display: 0-1000 (parameter adjustable 0-5000)

Kam kuchlanish: Masofadan boshqarish pulti batareyasi juda past, please replace the battery.

Tarmoq tushdi: Simsiz signal to'xtatiladi. Iltimos, qabul qilgichning quvvatini tekshiring, uni yana yoqing, and restart the remote control.

7.Masofadan boshqarish funktsiyasi operatsiya ko'rsatmalar

1） Turn on the remote control
When the receiver is powered on, the receiver working indicator flashes; install two AA batteries in the remote control, Quvvat tugmachasini yoqing, and the display shows a value,Muvaffaqiyatli ishga tushirish. The receiver working indicator light becomes solid.
2）Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3）W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4） Emergency stop function
Favqulodda vaziyat o'chirish tugmasi bosilganda, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5）Parameter menu (users are prohibited from modifying it privately)
Masofadan boshqarish pultining ba'zi funktsiyalari parametrlar orqali sozlanishi mumkin. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A and K9-B key to page through the menu and select parameters; hold down K1-A, and then press the K9-A/B button to modify parameters;
Parametr menyusidan chiqing: Saqlash yoki saqlamaslikni tanlang, and then press the K1-A button to confirm the exit;
F1W1 range: The display range value of the W1 knob on the display screen, adjustable from 0 ga 9999;
F2W2 range: The display range value of the W2 knob on the display screen, adjustable from 0 ga 9999;
F3W3 range: The display range value of the W3 knob on the display screen, adjustable from 0 ga 9999;
F4W4 range: The display range value of the W4 knob on the display screen, adjustable from 0 to 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;

8.Masofadan boshqarish pulti elektr xususiyatlari

9.Masofadan boshqarish hajmi

The final interpretation right of this product belongs only to our company.

Model: DH12S-P6S

Qo'llaniladigan uskunalar:wire saw/blade saw machine

2.Mahsulot uchun aksessuarlar diagrammasi

Eslatma: Siz uchta antennalardan birini tanlashingiz mumkin. The suction cup antenna is standard by default.

3.Masofadan boshqarish pulti Tasvir tavsifi

4.Discondentni kiritish

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parametrlar sozlanishi)
Automatic cutting main motor setting current: Setting: 28 (parametrlar sozlanishi)
Swing arm motor speed: Swing: 0-50

Kam kuchlanish: Masofadan boshqarish pulti batareyasi juda past, please replace the battery.

Tarmoq tushdi: Simsiz signal to'xtatiladi. Iltimos, qabul qilgichning quvvatini tekshiring, uni yana yoqing, and restart the remote control.

5.Masofadan boshqarish funktsiyasi operatsiya ko'rsatmalar

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, Quvvat tugmachasini yoqing, and the display will show the motor speed, indicating successful startup.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, burilmoq “Oldinga / teskari” Oldinga o'tish, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, burilmoq “Oldinga / teskari” teskari tomonga o'tish, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Aylantiring “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, burilmoq “Oldinga / teskari” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Burilmoq “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” kalit, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Ni bosing va ushlab turing “speed adjustment enable” tugmasini bosing va aylantiring “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “oldinga / teskari” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (Foydalanuvchilar ruxsatsiz o'zgartirish taqiqlanadi)

Enter the parameter menu:Qo'l rejimida, when the main motor speed is 0, oldinga / teskari tugmachani ketma-ket uch marta bosing, and then push it down three times in a row to enterthe parameter menu;
Parametr menyusidan chiqing: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, bajarilish 800, unit milli second,o'zgartirish taqiqlanadi;
Dreatsion parametr: Kesish oqim o'zgarishi qiymati ushbu qiymatdan oshganda, rapid deceleration begins, unit Ampere;
A1 ni tezlashtirish: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
A2 ni sekinlashtirish: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, o'zgartirish taqiqlanadi;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, o'zgartirish taqiqlanadi;
Maksimal oqim: The range of main motor feedback current, unit Ampere;
Maksimal xost: Remote control main motor speed adjustment display range;
Maksimal yurish: Invalid parameter;
Tezlik chegarasi ofset: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Avtomatik kesish, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;birlik: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Masofadan boshqarish pulti elektr xususiyatlari

7.Masofadan boshqarish hajmi

The final interpretation right of this product belongs only to our company.

Model: DH12s-ld

Qo'llaniladigan uskunalar:Crawler simegan mashinasi

Mahsulot uchun aksessuarlar diagrammasi

Eslatma: Siz uchta antennalardan birini tanlashingiz mumkin. The suction cup antenna is standard by default.

Masofadan boshqarish pulti Tasvir tavsifi

Discondentni kiritish

Katta motor tezligi：S1：0-50
Kichik motor tezligi: S2: 0-50
Maksimal maksimal sonbing:Favqulodda:0-30(parametrlar)
Maksimal oqimni avtomatik ravishda kesish: Tushunarli: 0-35 (parametrlar sozlanishi)
Chiziqli tuzatish qiymati: Df: -99-99 (1 birlik 0,02v)

Kam kuchlanish: Masofadan boshqarish pulti batareyasi juda past, please replace the battery.

Tarmoq tushdi: Simsiz signal to'xtatiladi. Iltimos, qabul qilgichning quvvatini tekshiring, uni yana yoqing, and restart the remote control.

Masofadan boshqarish funktsiyasi operatsiya ko'rsatmalar

1.Masofadan boshqarish pultini yoqing

Qachon yoqilgan bo'lsa, Qabul qilgichdagi RF-LED yorug'ligi miltillay boshlaydi;Ikkita AA batareyasini kesib o'ting, Quvvat tugmachasini yoqing, va displey motor tezligini ko'rsatadi, indicating successful startup.

2.Katta motor va tezlikni tartibga solish

Burilmoq “oldinga / teskari” Oldinga o'tish, Qabul qiluvchining katta motoriga yoqadi, va displey oldinga yo'naltiradi

Burilmoq “oldinga / teskari” teskari tomonga o'tish, Qabul qilgichning katta motori teskari tomonga o'zgaradi, va displey teskari ko'rinadi

Aylantiring “katta motor tezligini sozlash” Qabul qiluvchining katta motor tezligini sozlash hajmi 0-10V;

3.Kichik motor va tezlikni tartibga solish

Siljiting “oldinga / teskari” Oldinga o'tish, chap g'ildirak oldinga va truba oldinga olib keluvchining oldinga siljishi davom etmoqda, va displey oldinga yo'naltiradi

Burilmoq “Oldinga / teskari” teskari tomonga o'tish, Qabul qiluvchining chap g'ildiragi teskari va o'ng qanot teskari tomonga burilish yoqilgan, va displey teskari ko'rinadi

4.Chapga va o'ngga buriling

Burilmoq “Chap / o'ng” Chapga o'tish, Qabul qiluvchining o'ng g'ildiragi oldinga va yoqadi,va displey chapda ko'rsatilgan

Burilmoq “Chap / o'ngga buriling” To'g'ri burilishga o'tish, Qabul qiluvchining chap g'ildiragi oldinga olib keladi va yoqiladi, va displey burilish to'g'ri bo'ladi

5.Joyni aylantiring

Qo'l rejimida:
Joyida chapga buriling: Ni bosing va ushlab turing “Yoqib yubormoq” tugmasi, burilmoq “Chap / o'ng burilish” Chapga o'tish, chap g'ildirakning orqaga va o'ng g'ildirakchasining oldinga burilishi qayta qabul qilindi,va chapga burilishni boshlang;

Joyida o'ng tomonga buriling: Ni bosing va ushlab turing “Yoqib yubormoq” tugmasi, burilmoq “Chap / o'ng burilish” o'ngga o'tish, Qolgan qabul qiluvchining chap g'ildirakchasi va o'ng g'ildiragining teskari tomoni yoqilgan, va qabul qilgich to'g'ri tomonga burila boshlaydi;

6.Kichik motor tezligini cheklash

Avtomatik rejimda: ni bosing va ushlab turing “Yoqib yubormoq” tugmasini bosing va aylantiring “Kichik motor tezligini sozlash” avtomatik kesish paytida kichik motorning maksimal tezligini sozlash;

7.Avtomatik kesish

Birinchi qadam - bu katta motorni boshlash; Ikkinchi qadam - rejimidan o'tish tugmachasini yoqish “Avtomatik”; Uchinchi bosqich - bu kichik motorni boshlash va ekran namoyish qilinadi “Avtoulovni kesish”,avtomatik kesish rejimiga kiritilganligini bildiradi;

8. To'g'ri chiziq tuzatish

Chap va to'g'ri yurish motorlari oldinga va orqaga qarab harakatlansa, Chap va to'g'ri tezliklar mos kelmaydi, va to'g'ri yo'lning burilishlari. Chap va o'ng g'ildiraklarning tezligini sozlash uchun masofadan boshqarish pultining chiziqli tuzatish funktsiyasidan foydalanishingiz mumkin;
Tuzatish printsipi: Tuzatish funktsiyasi orqali, Chap g'ildirakning tezligi to'g'ri g'ildirak bilan bir xil tezlikka erishish uchun yaxshi sozlangan, Chap va o'ng g'ildiraklarning tezligini sinxronlashtirish va og'ishni bartaraf etish uchun;
Og'ishlarni tuzatish usuli: Qo'l rejimida, ni bosing va ushlab turing “Yoqib yubormoq” tugmasini bosing va aylantiring “Kichik motor tezligini tartibga solish”;
Chap g'ildirakning tezligi va displey ekranidagi tuzatish qiymatini oshirish uchun soat yo'nalishi bo'yicha aylantiring;
Chap g'ildirakning tezligini kamaytirish uchun soat miliga teskari tomonga burilib, pasayishiga olib keladi;
Tuzatish doirasi: Tuzatish qiymati -90 ga 90; Bitta tuzatish moslamasining kuchlanish kuchlanish hajmi 0,02v;

9. Parametr menyusi (Foydalanuvchilar ruxsatsiz o'zgartirish taqiqlanadi)

Masofadan boshqarish pultining ba'zi funktsiyalari parametrlar orqali sozlanishi mumkin. Qo'l rejimida, kichik motor tezligi s2 10, oldinga / teskari tugmachani ketma-ket uch marta bosing, va keyin parametr menyusini kiritish uchun uni uch marta pastga tushiring;
Parametr menyusidan chiqing: Saqlash yoki saqlamaslikni tanlang, Chiqishni tasdiqlash uchun yoqilgan tugmani bosing;
Maksimal oqim: Kesish vositasining ishlaydigan oqim oqimi 80% bu oqim;
Tezlikni boshqarish parametrlari: Avtomatik kesish boshqaruv parametrlari, bajarilish 800, o'zgartirish taqiqlanadi;
Dreatsion parametr: Avtomatik kesishni boshqarish parametrlari. Kesish oqim o'zgarishi qiymati ushbu qiymatdan oshganda,deceleration begins.
A1 ni tezlashtirish: Avtomatik kesishni boshqarish parametrlari, Kesish oqimi belgilangan kesilgan oqimdan past bo'lsa, tezlash tezligi;
A2 ni sekinlashtirish: Avtomatik kesishni boshqarish parametrlari, Kesish oqimi to'plamdan yuqori bo'lganda
oqim kesish, sekinlashuv tezligi;
Pichoq pichoqni qaytarish: yaroqsiz;
O'z-o'zini qulflashni boshlang: 0, O'z-o'zini qulflash yo'q; 1, o'z-o'zini qulflash. Yoqish tugmachasini bosing + forward and reverse to take effect and self-lock.
Maksimal yurish: the maximum speed of the small motor.
Oqim kesish: Avtomatik kesish uchun asosiy vositaning maksimal oqimini o'rnating. Agar fikr-mulohazalar mavjud bo'lsa, ushbu qiymatdan oshsa, it will start to decelerate.
Standart tezlik chegarasi: the default maximum speed of automatic cutting speed when turning on the machine.
Avtomatik rejim: 0, Avtomatik almashtirish avtomatik ravishda boshqariladi; 1, the automatic switch controls the automatic IO output point.
Tezlik chegarasi ofset: the maximum speed of the small motor during automatic cutting.
Maksimal xost: maximum speed of large motor.

Masofadan boshqarish pulti elektr xususiyatlari

Masofadan boshqarish hajmi

The final interpretation right of this product belongs only to our company.

Model：ATWGP-12

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, CNCning uzunligi, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, CNCning uzunligi, traveling machine tools, kesish va boshqa dasturlar, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, Mitsubishi, Telba, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 metr;
2. Avtomatik chastotalarni o'chirish funktsiyalarini qabul qiling va foydalaning 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-o'q, 8-o'q, 9-o'q, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, va hokazo.;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. Quvvatni kam sarflash dizayni, 2 AA batteries can be used for more than 1 oy;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

Eslatma:
1. Status indicator light:
Signal light (left): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Kam voltli signallar yorug'ligi (right): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, CNCning uzunligi, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, and making operation more convenient. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, CNCning uzunligi, traveling machine tools, kesish va boshqa dasturlar, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, Mitsubishi, Telba, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 metr;
2. Avtomatik chastotalarni o'chirish funktsiyalarini qabul qiling va foydalaning 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-o'q, 8-o'q, 9-o'q, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, va hokazo.;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. Quvvatni kam sarflash dizayni, 2 AA batteries can be used for more than 1 oy;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

Eslatma:
1. Status indicator light:
Signal light (left): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Kam voltli signallar yorug'ligi (right): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.