The remote control for automatic cutting of track car rope saw is suitable for track type rope saw
cutting machines. It uses the 485 Modbus RTU protocol to control the left and right track frequency
converters, as well as the large motor frequency conversion speed control start and the front, rear,
left and right direction controllers. And it can read the working current of the large motor frequency
converter through the 485 Modbus RTU protocol. By analyzing and comparing the current of the
large motor, the speed of the left and right tracks can be automatically adjusted in real time to
achieve automatic cutting function.

2. Product functional features

1. Adopting 433MHz wireless communication technology, with a wireless operating distance of 100 meters.
2. Adopt automatic frequency hopping function and use 32 sets of wireless remote controllers
simultaneously, without affecting each other.
3. Supports all frequency converters with 485 Modbus RTU protocol, and currently compatible frequency
converter brands include:上海謝林, 富士, Huichuan, 中晨, INVT, 同 . For brands
that are not compatible, please contact us for customization.
4. 支援調節速度, 開始, and current reading of large motor frequency converters.
5. 支援左右軌道頻率轉換器速度調節, 開始, 前, 返回, left and right control.
6. 支援左右軌道頻率轉換器嘅線性校正，令機器保持喺 a 入面
straight line.
7. Support automatic cutting function of rope saw, automatically adjust the left and right track speed in
real time according to the current information of the large motor.
8. It is also compatible with direct IO output control for motor start and stop, and analog voltage output
control for motor speed.

3. 產品規格

4. Product Function Introduction

筆記:
① 螢幕顯示:

② 模式開關:

③Enable:
組合掣, 有啲操作需要保持啟用掣先可以運作,see the instructions for each switch for details.
④Large motor switch:
使用 3 速重設開關, 拉呢個開關可以控制大電機嘅前進同逆轉. 發佈完之後, 州會繼續, 同埋畫面上面會有對應嘅顯示器. The S1↑ arrow indicates forward rotation, and the S1 ↓ arrow indicates everse rotation.
⑤ 小電機向前 / 反向開關:
The small motor is equipped with a 3-speed self-locking switch in front of it. Pressing the enable button and pulling this switch can control the small motor to move forward and backward, and the corresponding display will appear on the screen.The ↑↑ arrow represents forward, and the ↓↓ arrow represents backward.
⑥ Straight line correction:
用多轉編碼器旋鈕, press the enable button, turn the knob right, and display the straight line correction: Df: The left turn knob increases by 1 unit per rotation, and the left
motor speed increases by 0.1 單位; 轉咗旋鈕, 直線校正顯示: Df: On the right, every turn of the knob increases by 1 單位, and the speed of the right motor increases
by 0.1 unit.
⑦Small motor turning switch:
使用 3 速重設開關, 當手動操作時, 小電機可以控制到左或右. 一旦釋放, the remote control will automatically stop this action. In the forward state, when this switch is turned, the corresponding display will appear on the screen. The ←↑ arrow indicates left turn, and the ↑→ arrow indicates right turn.When in reverse mode, turn this switch and the corresponding display will appear on the screen. The ←↓ arrow indicates left turn, and the ↓→ arrow indicates right turn.
⑧ 大電機速度調節:
用多轉編碼器旋鈕, rotating 1 每次都格, 大型電機嘅速度值變化大約係 0.2 單位. Fast rotation can quickly modify the speed value of the large motor.
⑨ Small motor speed regulation:
用多轉編碼器旋鈕, 喺手動模式下, press the enable button and then rotate one grid at a time，the speed value of the left and right small motors changes by about 0.1 單位, and quick rotation can quickly modify the speed value of the small motor.In automatic mode, press the enable button and rotate one grid at a time,the speed limit value F of the small motor changes by approximately 0.1 單位. Rapid rotation can quickly modify the speed limit value of the small motor.
⑩ Remote control power switch
The remote control display screen is turned on.

5. 產品配件圖

6. 產品安裝指南
6.1 Product installation steps
1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver through wires.
3. After fixing the receiver, it is necessary to connect the antenna equipped with the receiver and install or place the outer end of the antenna outside the electrical cabinet. 建議將佢放係電櫃頂部，以獲得最佳訊號效果. It is forbidden to leave the antenna unconnected or place it inside the electrical cabinet, as it may cause the signal to be unusable.
4. 最終, install the battery on the remote control, 收緊電池蓋, and turn on the power switch of the remote control. After the remote control display screen shows the normal
working interface, remote control operations can be performed.

6.2 接收器安裝尺寸

6.3 接收器接線參考圖

7. 產品運作指示
7.1 遠端控制參數設定
Method to enter the remote control backend parameters:

Turn the mode switch to manual mode, 調整小型電機嘅速度，調整到 25 on both sides, 或者 0, 10, 20, 40, 50 on all sides, and continuously turn the forward switch of the large motor up 3 times and down 3 次次;
用 “小型電機速度控制” knob to flip pages, press the enable button, and then turn the small motor speed control knob to modify parameters. After modification, 將頁面轉到最後,選擇 “Save” to exit, and press the enable button to exit the menu;
參數如下:
最大電流: feedback range of large motor current, set range 15-200A, 預設 100;
速度控制參數: 自動模式, small motor automatically accelerates faster or slower,越細越快, set range 200-1500, 預設 800;
減速參數: Set the upper limit that allows the motor speed to change. 當當前變化超出呢個值, the deceleration will occur. The smaller, the faster the deceleration of the left and right motors, 有一系列 05-12 and a default of 06;
加速 a1: The larger the motor speed, the faster it increases, 有一系列 00-06 and a default of 01;
減速 a2: The larger the motor speed, the faster it decreases, 有一系列 00-06 and a default of 02;
啟用速度調節: Does the small motor speed regulation need to be enabled? 00 does not enable, 01 enables, default is 01;
開始自鎖: Does the large motor automatically maintain self-locking after the forward and reverse switches are released? 00 does not hold, 01 holds, default 01
最大行路: maximum speed of left and right motors, 範圍 10-100, 預設 50;
切割電流: maximum cutting current, displayed on the screen as IC value, 範圍 15-160, default 30,
corresponding to IC: 30 displayed on the screen. The upper limit of this parameter is 80% of the maximum current;
預設速度限制: The default small motor automatic cutting speed when turned on is within the range of 0-100, with a default of 10. The screen displays F1.0, and this parameter is only accurate when the maximum walking is set to 50.
自動模式: Set to 00, the automatic/manual switch is a mode switch. Set to 01, the automatic/manual switch is set to the automatic position, the display screen shows lighting, and the automatic terminal output on the receiver is closed. When set to manual, the automatic output terminal is disconnected;
Speed limit deviation: The upper limit of the automatic cutting speed of the small motor ranges from 00 去 200, with a default of 60 and a corresponding display of 6.0 on the screen; Upper limit of display value=speed limit offset x 0.1;
最大主機: maximum speed of the large motor, 範圍 10-100, 預設 50;
Mbus equipment (強制): Selection of large motor frequency converter model, 範圍 00-03, 預設 03;
00- Shanghai Xielin 01-Fuji
02-INVT 03-Inovance（Zhongchen, 機械人：
SBUS 設備 (強制): 小型電機頻率轉換器模型選擇, 範圍 00-05, 預設 03;

00- Shanghai Xielin 01-Fuji
02-INVT 03-Inovance（Zhongchen, 機械人：

04-安川達 05- 冇

7.2 頻率轉換器嘅參數設定
1. 命令來源選擇: 通訊命令頻道
2. 主要頻率來源選擇: 溝通畀咗
3. 鮑德率: 19200
4. 資料格式: 冇驗證, 資料格式<8-N-1>
5. 本地地址: 將左邊頻率轉換器設定為 1, 正確頻率轉換器到 2, 同
the large motor frequency converter to 3
7.3 遙控控制操作指示
1. 喺機器上面開機, 開遙控器, enter the remote control backend, set the
remote control backend parameters, mainly setting the small motor and large motor frequency
converter models: (如果機器製造商已經設定咗，就 skip 呢個步驟);
2. 設定頻率轉換器嘅參數 (skip this step if the machine manufacturer
has already set it);
3. 將遙控器設定為手動模式, and then use the remote control to move the machine to
the working position;
4. 係手動模式下, set the cutting current of the large motor to IC and the speed of the large motor
5. 切換到自動模式，並為小型電機設定切割速度限制 F 值;
6. 係自動模式下, 轉大電機開關向前開始大電機, then turn
the small motor switch to forward or reverse, and the remote control enters automatic cutting
mode to start cutting.

8.產品故障排除

9.維護
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the battery compartment and metal shrapnel area clean.
4. Please avoid damaging the remote control due to squeezing and falling.
5. 如果唔用好耐, please remove the battery and store the remote control and battery in a clean
and safe place.
6.儲存同運輸期間, attention should be paid to moisture and shock resistance.

10. 安全資訊
1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery is too low to avoid errors caused by
insufficient power, which may result in the remote control being unable to operate.
3. 如果需要維修, 請聯絡廠商. 如果損壞係由自我修復引起, the manufacturer
will not provide warranty.

模型: DH01R-4W-26K

適用設備:各種工業設備

2.產品配件圖

筆記薄: 你可以揀三個天線之一. The suction cup antenna is standard by default.

3.產品模型描述

筆記薄:
① DH01R 系列, 如果後綴包含 T, 佢嘅意思係同緊急停止輸出;冇 T, it means without emergency stop output.

② 如果冇模擬輸出, 唔需要評論 0W 或者 0R; 類比量 W1, W2, W3, 同埋 W4 預設係 0-10V 模擬電壓輸出; 同時, W1 同 W2 可以擴充到 2 隔離數碼電位計輸出, 有一系列 0 -5K ohms, 1⁄2 瓦; 決議: 20 ohms. 兩個數碼電位可以用嚟控制焊接機嘅焊接電流同焊接電壓. 如果需要數碼電位計輸出, user notes are required.

④ 模擬輸入, 由 1 去 2, 表明有 1 去 2 模擬輸入(最高 2 頻道); 當有模擬輸入, 你需要注意模擬輸入嘅電壓範圍 (我哋嘅接收器預設係 0 -5V, 用戶亦可以記低作為 4-20 mA 或 0-10V, 等等。) 同埋模擬數量嘅相應顯示範圍 (例如: 佈置 0-100 伏特或者 0-1000 安讀)

These two analog quantities can be used as displays for welding current and welding voltage.

4.特徵

12 最大 26 繼電器輸出;
22 最大 4 模擬 0-10V 輸出嘅通道 (顯示範圍可以自訂): 支持 2 延伸隔離數碼電位計輸出嘅通道;
32 模擬輸入; 同埋顯示喺遙控器上面, 顯示範圍可以自訂
42 緊急停止繼電器輸出正常閉合接觸點;
5由 3 AA 電池, 低功耗設計;
6） 無線操作距離係 200 米;
7） 保護級 IP67;
8） 用交叉開關操作, 支援兩個 4 方向交叉開關;
9）Back strap design.

5.遠端控制開關描述

6.顯示內容介紹

W1 掣價值: W1: 0-1000 (參數可調節 0-9999)
W2 旋鈕價值: W2: 0-5000 (參數可調節 0-9999)
W3 旋鈕價值: W3: 0-5000 (參數可調節 0-9999)
W4 旋鈕價值: W4: 0-5000 (參數可調節 0-9999)
ADC1 反饋顯示: 0-1000 (參數可調節 0-5000)
ADC2 反饋顯示: 0-1000 (參數可調節 0-5000)

低電壓: 遙控電池太低, please replace the battery.

網絡掉落: 無線訊號中斷. 請檢查接收器嘅力量, 再次開機, and restart the remote control.

7.遠端控制功能操作指令

1） 開啟遙控器
當接收器係開機嘅時候, 接收器工作指示燈閃爍; 係遙控器安裝兩個 AA 電池, 開啟電源開關, 而顯示屏顯示價值,表示成功嘅初創公司. The receiver working indicator light becomes solid.
2） 開關和按鈕功能
遙控器上嘅扭開同按鈕嘅任何操作都可以控制接收器上嘅相應開關訊號輸出點. 接收器上嘅所有開關訊號輸出點都係正常預設;
32 嘅 W1-W4 速度調整
任意旋轉 W1-W4 嘅旋鈕，以便操作接收器端嘅相應模擬輸出訊號或電位計訊號. 接收器端嘅模擬輸出訊號預設係 0-10V 電壓訊號, 而電位計訊號預設為 0-5K;
42 緊急停止功能
當按緊急停止掣時, 所有開關訊號輸出都斷開，模擬輸出斷開; 緊急停止發佈後, 所有開關訊號都還原，並還原模擬輸出; 5 遙控器關閉後幾秒, 所有開關訊號輸出都斷開，模擬量仍然無變. 當遙控器開啟時, 開關訊號輸出自動恢復;
52 參數選單 (用戶係禁止私下修改)
遙控器嘅部分功能可以透過參數調整. 當顯示器 W1 = 0 時, 按下 K9-B 掣 3 連續次, 然後按下 K9-A 按鈕 3 連續次要輸入參數選單; K9-A 同 K9-B 鍵可以透過選單頁面，然後選擇參數; 抱住 K1-A, 然後按下 K9-A / B 按鈕，以修改參數;
退出參數選單: 選擇儲蓄或者唔儲存, 然後按下 K1-A 按鈕確認退出;
F1W1 系列: 顯示屏幕上嘅 W1 旋鈕嘅顯示範圍值, 可以調整 0 去 9999;
F2W2 範圍: 顯示屏幕上嘅 W2 旋鈕嘅顯示範圍值, 可以調整 0 去 9999;
F3W3 範圍: 顯示屏幕上嘅 W3 旋鈕嘅顯示範圍值, 可以調整 0 去 9999;
F4W4 範圍: 顯示屏幕上嘅 W4 旋鈕嘅顯示範圍值, 可以調整 0 to 9999
F5A1 範圍: 顯示 ADC1 反饋顯示範圍值, 0-5000 可調節;
F6A2 範圍: 顯示 ADC2 反饋顯示範圍值, 0-5000 可調節;
警報電流: 設定 ADC1 同埋 ADC2 反饋顯示嘅警報值. 當 ADC1 同 ADC2 超過呢個值, 遙控顯示器會警報; 當呢個值係 0, 警報函數係無效嘅;

8.遙控器電氣特性

9.遠端控制大小

The final interpretation right of this product belongs only to our company.

模型: DH12S-P6

適用設備:電線鋸 / 刀片鋸機

2.產品配件圖

筆記薄: 你可以揀三個天線之一. The suction cup antenna is standard by default.

3.遠端控制開關描述

4.顯示內容介紹

主要電機速度: 主要: 0-50
旅行電機速度: 線: 0-50
自動切割旅行電機嘅最大速度限制: 速度: 0-30
(參數可調節)
自動切割主要電機設定電流: 設定: 28 (參數可調節)
摇摆臂電機速度: 搖: 0-50

低電壓: 遙控電池太低, please replace the battery.

網絡掉落: 無線訊號中斷. 請檢查接收器嘅力量, 再次開機, and restart the remote control.

5.遠端控制功能操作指令

1） 遙控器上轉動

當接收器係開機嘅時候, 接收器上嘅 D2 電源燈永遠都係開嘅, 而 D1 訊號燈就開始閃爍; 係遙控器安裝兩個 AA 電池, 開啟電源開關, 而顯示屏會顯示電機速度, indicating successful startup.

2） 大電機與調節速度 / 主要電機和速度調節

按住按住 “速度監管啟用”, 轉個 “前進 / 逆向” 轉用向前, 而接收器嘅主要電機就會開啟;
按住按住 “速度監管啟用”, 轉個 “前進 / 逆向” 轉用反轉, 而接收器嘅主要電機就會反轉同開;只要將開關移至中間或反向方向, 而主電機會立即停止，而唔會按速度控制啟用按鈕;旋轉個 “大電機” 旋鈕調整接收器主電機逆變器嘅速度調節電壓到 0-10V;

3） 旅遊電機

按住按住 “速度調整啟用”, 轉個 “前進 / 逆向” 轉用向前或向後, 而行走電機就會以高速移動 50;

4） 摇臂電機和速度調節

轉咗個 “摇臂 / 逆向” 轉用摇臂或退役, 同埋接收器嘅摇臂電機開始; 然後旋轉個 “速度調整” 掣調整摇臂電機速度;

按住按住 “速度調整啟用”, 然後拉個 “摇臂 / 逆向” 切換, 摇臂電機會以高速移動 50;

5） 旅遊電機限速調整

按住個 “調整速度” 按鈕，然後旋轉 “調整速度” 調整自動切割期間行駛電機最大限速;

62 自動切割

第一步係開始主電機; 第二步係調整行走電機嘅最大速度限制; 第三步係移動個 “向前 / 逆轉” 向前或向後切換，進入自動切割模式;

72 參數選單 (使用者喺未經許可嘅情況下，就禁止修改呢個功能)

輸入參數選單:係手動模式下, 當主要電機速度係 0, 連續三次推向前 / 反向開關, 然後連續按三次，進入參數選單;
退出參數選單: 轉轉速度調整旋鈕, 揀儲存或者唔儲存, 同埋撳啟用掣確認;
額定電流: 主電機電流最大值, 單位安培;
速度調整參數: 自動切割控制參數, 預設 800, 單位毫米第二,禁止修改;
減速參數: 當切割電流變化值超過呢個值, 快速減速開始, 單位安培;
加速 a1: 當切割電流低於設定切割電流時, 行走電機嘅每個加速度都增加嘅速度值;
減速 a2: 當切割電流高於設定切割電流, 由行走電機嘅每次減速降低嘅速度值;
摇摆臂電流: 預設價值, 禁止修改;
停止時間: 自動模式電流過載關閉後, 電流會係一段時間之後再偵測到. 如果佢係少過設定電流, 行走電機會自動開始; 單位第二, 預設值, 禁止修改;
最大電流: 主要運動反饋電流範圍, 單位安培;
最大主機: 遠端控制主電機速度調整顯示範圍;
最大行路: 無效參數;
速度限制偏移: 自動切割期間, 遙控顯示行走電機速度限制 = 50% 呢個參數;
增加敏感度: 當主要運動反饋電流增加, 每次增加超過呢個值, 行走電機加速;
降低敏感度: 當主電機嘅反饋電流會降低, 同埋每次降低值超過呢個值, 行走電機減慢;
敏感度抵消: 加入同減去敏感度參數嘅偏移增量;
設定電流: 自動切割, 主要運動反饋電流嘅關口. 如果超過呢個值,行走電機開始減慢;下面呢個價值, 行走電機開始加速;單位: 阿姆佩雷;
閒置出口: 當自動模式開始時, 如果主要嘅運動反饋電流係少過呢個值,佢會係閒置模式。如果係呢個值更大, 佢會退出閒置模式，進入切割模式。單位係安培;
無負載電流:當自動模式開始時, 如果主要嘅運動反饋電流係少過呢個值,佢係冇負荷模式。如果係呢個值更大, 佢會退出無負荷模式，然後進入切割模式。單元係 Ampere;
摇摆臂速度: 開始時摇臂電機嘅初始速度;
切割模式: 喺刀片鋸同電線鋸模式之間切換, 而參數係開關後會相應切換; 喺刀片鋸模式入面, 遙控顯示器加入摇摆臂電機, 同時係電線鋸模式, 冇摇臂電機;
辯論時間: 當主要電機反饋電流超過停止電流, 反饋電流會持續檢測. 反彈時間係呢個連續檢測嘅持續時間。呢個時候之後, 如果主電機電流仍然超過停止電流, 行走電機會停止;否則, 行走電機會停止. 電機會繼續前進;
停止電流: 主要嘅運動反饋電流超過呢個值, 而行走電機就會停止;單位係安培;
偏移預設: 當遙控器開咗時行走電機速度限制嘅初始值 = 50% 呢個價值;

6.遙控器電氣特性

7.遠端控制大小

The final interpretation right of this product belongs only to our company.

模型: DH12S-LD

適用設備:爬行線鋸機

產品配件圖

筆記薄: 你可以揀三個天線之一. The suction cup antenna is standard by default.

遠端控制開關描述

顯示內容介紹

大電機速度：S1：0-50
小電機速度: S2: 0-50
最大速度極限特殊剪裁小運動:F:0-30(參數可以調整)
自動切割最大電流: Ic: 0-35 (參數可調節)
線性校正值: Df: -99-99 (1 單位約為 0.02V)

低電壓: 遙控電池太低, please replace the battery.

網絡掉落: 無線訊號中斷. 請檢查接收器嘅力量, 再次開機, and restart the remote control.

遠端控制功能操作指令

1.開啟遙控器

當個係開電, 接收器上嘅 RF-LED 燈開始閃爍;安裝兩個 AA 電池係 spient 遙控器, 開啟電源開關, 而顯示屏會顯示電機速度, indicating successful startup.

2.大電機同調節速度

轉咗個 “向前 / 逆轉” 轉用向前, 接收器嘅大電機會開, 同埋顯示屏會向前展示

轉咗個 “向前 / 逆轉” 轉用反轉, 接收器嘅大電機會反轉, 而顯示屏會顯示反向

旋轉個 “大電機速度調整” 旋鈕，調整接收器嘅大電機速度調整輸出電壓 0-10V;

3.小型電機同調節速度

移動個 “向前 / 逆轉” 轉用向前, 左輪向前同右輪向前嘅接收器開咗, 同埋顯示屏向前展

轉咗個 “前進 / 逆向” 轉用反轉, 開機左輪反向同右輪反轉, 同埋顯示屏顯示反轉

4.左右轉

轉咗個 “左 / 右” 轉左, 接收器嘅右輪會向前同埋開啟,同埋顯示屏會顯示咗

轉咗個 “轉咗 / 右” 轉右轉, 接收器嘅左輪會向前轉，然後開, 而顯示屏會顯示轉右

5.轉動到位

係手動模式下:
左轉到位: 按住個 “令到” 鈕, 轉個 “左 / 右轉” 轉左, 左輪向後同右輪向前嘅接收器開咗,同埋開始咗轉咗;

右轉到位: 按住個 “令到” 鈕, 轉個 “左 / 右轉” 轉右轉, 左輪向前同右輪反轉嘅接收器開咗, 而接收器就開始右轉;

6.小型電機限速調整

係自動模式下: 按住個 “令到” 按鈕，然後旋轉 “小型電機速度調整” 喺自動切割期間調整小型電機嘅最大速度;

7.自動切割

第一步係開始大電機; 第二步係將模式開關切換去 “自動”; 第三步係開始小型電機，畫面會顯示 “切割自動”,表示已經進入自動切割模式;

8. 直線校正

當左右行走電機向前同向後移動, 左右速度係唔一致嘅, 同埋直線行路偏離. 你可以用遙控器嘅線性校正功能去微調左右輪嘅速度;
矯正原則: 透過校正功能, 左輪嘅速度係微調，達到同右輪嘅速度, 以同步左右輪嘅速度同消除偏差;
偏差校正操作方法: 係手動模式下, 按住個 “令到” 按鈕，然後旋轉 “小型電機速度監管”;
順時針旋轉，增加咗輪速度電壓，而顯示屏幕上嘅校正值就會增加;
逆時針旋轉，降低左輪速度電壓及顯示校正值降低;
矯正範圍: 矯正價值 -90 去 90; 一個校正單元嘅校正電壓大約係 0.02V;

9. 參數選單 (使用者喺未經許可嘅情況下，就禁止修改呢個功能)

遙控器嘅部分功能可以透過參數調整. 係手動模式下, 當小型電機速度 S2 係 10, 連續三次推向前 / 反向開關, 然後連續按三次，進入參數選單;
退出參數選單: 選擇儲蓄或者唔儲存, 然後按啟用掣確認退出;
最大電流: 切割電機嘅運作額定電流係 80% 呢個電流;
速度控制參數: 自動切割控制參數, 預設 800, 禁止修改;
減速參數: 自動切割控制參數. 當切割電流變化值超過呢個值,deceleration begins.
加速 a1: 自動切割控制參數, 當切割電流低於設定切割電流時, 加速速度;
減速 a2: 自動切割控制參數, 當切割電流高於集合時
切割電流, 減速速度;
自動刀收縮: 無效;
開始自鎖: 0, 冇自我鎖; 1, 自鎖. 撳一下啟用密鑰 + forward and reverse to take effect and self-lock.
最大行路: the maximum speed of the small motor.
切割電流: 設定主電機最大電流，以便自動切割. 如果反饋電流超過呢個值, it will start to decelerate.
預設速度限制: the default maximum speed of automatic cutting speed when turning on the machine.
自動模式: 0, 自動控制自動開關; 1, the automatic switch controls the automatic IO output point.
速度限制偏移: the maximum speed of the small motor during automatic cutting.
最大主機: maximum speed of large motor.

遙控器電氣特性

遠端控制大小

The final interpretation right of this product belongs only to our company.

模型：ATWGP-12

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, 數控車床, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, 同埋令到營運更加方便. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, 數控車床, traveling machine tools, 切割等應用, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, 三菱, 法努克, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 米;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-軸, 8-軸, 9-軸, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, 等等。;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. 低功耗設計, 2 AA batteries can be used for more than 1 month;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

筆記薄:
1. Status indicator light:
Signal light (左): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Low voltage alarm light (右): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.

Adaptation system: all CNC systems with handwheel interface

This product is a manual pulse generator used with CNC machine tools. It has beenwidely used in fields such as CNC machine tools, 數控車床, machining centers,CNC engraving and milling machines. This product uses wireless transmissiontechnology, eliminating the need for traditional spring wire connections, reducingequipment failures caused by cables, eliminating cable drag, oil and other contamination, 同埋令到營運更加方便. The product package includes the receiver and wireless electronic handwheel. The receiver is connected to the CNC equipment through a network cable, and the electronic handwheel (hand pulse generator) is connected and communicated with the receiver through wireless transmission technology. The operator holds the handwheel and can get rid of the connection constraints of the spring wire and move freely. For large-scale gantry milling, 數控車床, traveling machine tools, 切割等應用, it brings great convenience and improves work efficiency.

Supports various system brands such as Siemens, 三菱, 法努克, TaiwanXindai, Baoyuan, Fagor, Huazhong CNC, Guangzhou CNC, and otherCNC systemsthat support handwheel interfaces.

1. Using the 433MHZ wireless communication frequency band, the wireless operating distance is 40 米;
2. Adopt automatic frequency hopping function and use 32 sets of wireless handwheels at the same time without affecting each other;
3. Supports emergency stop button and 3 custom button switch outputs;
4. Supports multiple axis selections of 6-axis, 7-軸, 8-軸, 9-軸, 10-axis and 12-axis, with 3-speed and 4-speed magnification.Axis selection and magnification switches support various signal types such as binary coding, point-to-point, gray code, 等等。;
5. Supports 5V differential pulse signal, 24V pulse signal and other pulse signal types;
6. 低功耗設計, 2 AA batteries can be used for more than 1 month;
7. Supports external extension antenna, suitable for various machine tool installation environments, ensuring signal stability;

筆記薄:
1. Status indicator light:
Signal light (左): The signal light is always on when the handwheelis operated, and does not light up when not operating;
Low voltage alarm light (右): When the battery power is too low,the alarm light flashes or stays on;
2. Enable button:
After pressing and holding the enable button, the axis selection and magnification signals are activated, and the pulse encoder output is valid;
3. Custom button:
A button without any function can control a corresponding switch output on the receiver;

COM1: Common terminal for axis selection magnification signal output; can be connected to 0-24V public signal
COM2: Common terminal of 3 custom button outputs;

*Axis selection and magnification can be selected through software, coding or point-to-point, please consult the staff for details

The final interpretation right of this product belongs to our company.