西门子的具体应用 – WIXHC技术 https://www.wixhc.cn 行业领导者 Wed, 05 Nov 2025 06:21:59 +0000 zh-CN hourly 1 https://wordpress.org/?v=6.8.3 有线电子手轮使用说明书 https://www.wixhc.cn/product/wired-electronic-handwheel-instruction-manual Wed, 05 Nov 2025 06:13:13 +0000 https://www.wixhc.cn/?post_type=product&p=4678

1. 产品简介

Electronic handwheel is used for manual guidance, 定位, 工具对齐, 以及CNC机床上的其他操作. This model of electronic handwheel is a Siemens actual display wired electronic handwheel. The handwheel is connected to the X130 interface of the Siemens system through a network cable, and the system coordinates are read and displayed on the LCD screen of the handwheel through S7 protocol communication. The handwheel can also control system axis selection, 放大, buttons, andother signals through communication.
2.产品功能特点
1. 使用6芯航空插头连接线进行连接, 手轮电缆长度为 10 meters.
2. 手轮屏可显示系统工件坐标, 机械坐标,进给率, 轴选择, 放大, and other information.
3. 支持紧急停止按钮, 切换IO信号输出, and the hand wheel shutdown emergency stop is still valid.
4. 支持 6 自定义按钮, 开关IO信号, and can output signals to the system through IO wiring or communication.
5. 支持 6 或者 8 轴控制, with switch IO signals that can be output to the system through IO wiring or communication.
6. 支持 3 或者 4 levels of magnification control, with switch IO signals that can be output to the system through IO wiring or communication.
7. 支持脉冲编码器, 100 脉冲/转弯, can output signals to the system through AB pulse wiring.
8. Supports Siemens S7 protocol and Siemens 828D, 840DSL, ONE and other model systems.

 

3. 产品规格
Handwheel working power supply voltage DC24V/1A
接收器电源电压 DC24V/1A
Receiver IO output load range DC24V
Hand wheel end cable length 10m
Receiver end cable length 1m
Receiver end network cable length 3m
Operating temperature -25℃<x<55℃
Anti-fall height 1m
Custom Button Quantity 6
Product dimensions 233*90.7*77.4（mm）

4.产品功能简介

笔记:
Emergency stop button:
按下紧急停止按钮, 接收器上的两组急停IO输出将断开, and all functions of the handwheel will be invalid.
After releasing the emergency stop, 接收器上的紧急停止IO输出关闭, and all functions of the handwheel are restored.
② Screen display:

 

PLC: 0000 indicates that the network cable is not connected, PLC: 1010 indicates that the network cable is successfully connected to the PLC system.
PLC: 1110 represents successful writing of system data to the handwheel, PLC: 0001 represents successful connection to the computer.
③ Custom button:
6 自定义按钮, 每个对应接收器上的一个IO输出点, also connected to the system through communication.
④ Axis selection switch:
The axis selection switch can switch the movement axis controlled by the handwheel.
⑤ Enable button:
Press and hold either enable button on both sides to activate the pulse encoder by shaking it. And the two groups on the receiver enable IO output to conduct, release the enable button to enable IO output to disconnect.
⑥ Magnification switch:The magnification switch can switch the magnification
controlled by the handwheel.
⑦ Pulse encoder:
按住启用按钮, 摇动脉冲编码器, 发出脉冲信号, and control the movement of the machine axis.
⑧ Handwheel cable:

Cable connecting the handwheel and receiver, aviation plug, used for handwheel power supply and communication.

5. 产品配件图

6. 产品安装指南
6.1 产品安装步骤
1. Install the receiver into the electrical cabinet through the screw holes at the four corners.
2. 请参阅我们的接收器接线图并将其与您的现场设备进行比较. Connect the device to the receiver through cables and connect the receiver to the X130 interface of the system using Ethernet cables.
3. 固定好接收器后, install the aviation plug base at the handwheel opening position on the panel, and plug the other end of the base into the handwheel interface on the receiver. Then insert the aviation plug of the handwheel cable into the base and tighten the fixing device.

 

6.2 接收器安装尺寸

6.3 Installation dimensions of aviation plugs

6.4 接收器接线参考图
7.产品操作说明

1. When the receiver is powered on and the working indicator light of the receiver flashes, connect the receiver to the computer with a network cable, set the fixed IP address of the computer, and use the network configuration tool software to set the network parameters of the handwheel function. For specific setting methods, refer to the “LXWGP-ETS Wired Handwheel User Manual”.

2.After the receiver is set up, the system needs to program a PLC program. Please refer to the “LXWGP-ETS Different Siemens Numerical Control System Setting Methods” and PLC program routine materials for details.

3.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.

4.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X interface of the system. Connect the receiver power supply and pulse line.
5. Select axis selection: Switch the axis selection switch and select the axis you want to operate on.
6. 选择放大倍率: Switch the magnification switch and select the magnification level you need.
7. 移动轴: 按住启用按钮, 选择轴选择开关, 选择放大开关, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.
8. Press and hold any custom button to turn on the IO output of the corresponding button in the receiver, and release the button to turn off the output.
9. 按下紧急停止按钮, 接收器对应的急停IO输出会断开, 手轮功能将被禁用, 松开紧急停止按钮, 急停IO输出将被关闭, and the handwheel function will be restored.
8.产品模型描述

① LXWGP represents a wired appearance style, and the receiver communication interface
is an Ethernet interface.
② : Represents Siemens system specific.
③ : 表示轴选择开关的数量, represents axes, and represents
axes.
④ : represents the type of axis selection and magnification signal, A represents
point-to-point output signal, and B represents encoded output signal.

9.Product trouble shooting

10.维护
1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. 请避免挤压, 跌倒, 碰撞, ETC. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. 如果很长一段时间没有使用, please store the handwheel in a clean and safe place.During storage and transportation, attention should be paid to moisture and shock resistance.
11. 安全信息

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. If any abnormal situation occurs with the handwheel, please stop using it immediately and troubleshoot. Before troubleshooting, it is forbidden to use the faulty handwheel again to avoid safety accidents caused by unknown handwheel faults;
3. 如果需要维修, 请联系制造商. 如果损害是由自修理造成的, 制造商将不提供保修

 

]]> 专用的无线遥控器用于CNC垂直车床操作说明 https://www.wixhc.cn/product/vertical-lathe-wireless-electronic-handwheel-copy Wed, 03 Sep 2025 01:06:33 +0000 https://www.wixhc.cn/?post_type=product&p=4666

1.产品简介

采用数控立式车床专用无线遥控器进行手动引导, 定位, 对刀, 以及数控立式机床上的其他操作. 该产品采用无线传输技术, 无需传统的弹簧线连接, 减少电缆引起的设备故障, 消除电缆拖拽、油污等弊端, 让操作更便捷. 广泛适用于数控立式车床等各种立式车床, 单柱立式车床, 和双柱立式车床。也可适配市场上多种数控系统, 例如西门子,
三菱, Fanuc, and Syntec.

2. 产品功能特点

1. 领养 433 MHz无线通信技术, 无线操作距离为 40 meters.
2.采用自动跳频功能并使用 32 同时多组无线遥控器, without affecting each other.
3. 支持紧急停止按钮, switch IO signal output.
4. 支持 2 可自定义的按钮, with switch-type IO signal output.
5. 支持 -2 axis control.
6. Supports 3-level magnification control.
7. 支持启用按钮功能, 可输出开/关IO信号，控制轴选择, 倍增因子, 和编码器。
8. Support for axis selection and magnification modification through software to change the encoding type.
9. 支持脉冲编码器, 规格为 100 pulses per revolution.
3. 产品规格
无线遥控工作电压、电流
3V/14MA
电池规格 2 AA 碱性电池, size 5
无线遥控低电压报警范围 < 2.3v
接收器电源电压 DC5V-24V/A
接收器急停输出负载范围 AC125V-1A/DC30V-2A
接收器使能输出负载范围
AC125V-1A/DC30V-2A
接收器自定义按钮输出负载范围 直流24V/50mA
接收轴选择输出负载范围 直流24V/50mA
接收放大输出负载范围 直流24V/50mA
手持终端发射功率
15分贝
接收机接收灵敏度 -100分贝
无线通讯频率 433MHz频段
无线通讯距离 无障碍距离 40 仪表
工作温度 -25℃ < x < 55℃
防坠落高度 1 (仪表)
自定义按钮数量 2
4. 产品功能介绍



笔记:

① 脉冲编码器:
按住启用按钮, 摇动脉冲编码器, 发出脉冲信号,and control the movement ofthe machine axis.
② 启用按钮:
按任一侧的任一启用按钮, 接收器上的两组使能IO输出将导通. 松开使能按钮，断开使能IO输出; 并在切换轴选择倍率并摇动手轮之前,启用按钮需要按住才有效; This function can be cancelled through configuration software.

③ 指示灯:
左侧灯: 电源亮起,手轮使用轴选择OFF上电, 通电后此灯常亮;
中光: 操作手轮任何功能时亮起的信号灯, 且无操作时不亮;
右侧灯: 低压警报灯, 电池电量低,该灯闪烁或持续亮起, battery needs to be replaced.

④ 紧急停止按钮:
按下紧急停止按钮, 接收器上的两组急停IO输出将断开, and all functions of the handwheel will be invalid.

⑤ 倍率开关:
按住启用按钮可切换放大倍率开关, which can switch the magnification controlled by the handwheel.

⑥ 轴选择开关 (电源开关):
按住使能按钮可切换轴选择开关, 可切换手轮控制的运动轴. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ 自定义按钮:
两个自定义按钮, each corresponding to an IO output point on the receiver.

5. 产品配件图

6. 产品安装指南
6.1 产品安装步骤

1. 通过背面卡扣将接收器安装到电气柜中, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. 请参阅我们的接收器接线图并将其与您的现场设备进行比较. Connect the equipment to the receiver via cables.
3.接收器正确固定后, 配备了接收器的天线必须连接, 天线外端应安装或放置在电气柜外. 建议将其放在电柜的顶部以获得最佳信号效果. 禁止将天线不连接或放置在电气柜内, as this may result in the signal being unusable.
4. 最后, 打开手轮电源开关, and you can operate the machine remotely using the handwheel.

6.2 接收器安装尺寸

6.3 接收器接线参考图

7. 产品操作说明
1. 打开机器和接收器电源. 接收器工作指示灯闪烁. 将电池安装到无线电子手轮中, 固定电池盖, 和
打开无线电子手轮电源开关. The handwheel’s battery level indicator light is on.
2. 选择坐标轴: 按住启用按钮, 切换轴选择开关, and select the axis you want to operate.
3. 选择放大倍率: 按住启用按钮, 切换放大开关,and select the desired magnification level.
4. 移动轴: 按住启用按钮, 选择轴选择开关, 选择放大开关, 然后旋转脉冲编码器. 顺时针旋转可移动
positive axis and counterclockwise to move the negative axis.
5. 按住任何自定义按钮, 接收器对应按键IO输出将打开. 松开按钮, and the output will be turned off.
6. 按下紧急停止按钮, 接收器对应的急停IO输出会断开, 手轮功能将被禁用,松开紧急停止按钮, 急停IO输出将被关闭, and the handwheel function will be restored.
7. 如果一段时间内没有手轮操作, 它会自动进入睡眠模式以减少功耗. 当它再次使用时, the handwheel can be activated by pressing the enable button.
8. 如果长时间不使用手轮, 建议将手轮轴切换至OFF位置, 关闭手轮动力, and extend the battery life.

8. 产品模型描述

① :ZTWGP代表外观风格
②：脉冲输出参数:
01: 表示脉冲输出信号为A, 乙; 脉冲电压5V; pulse quantity 100PPR.
02：表示脉冲输出信号为A、B; 脉冲电压12V; pulse quantity 100PPR.
03：表示脉冲输出信号为A, 乙, 一个 -, 乙 -; 脉冲电压5V; pulse quantity 100PPR.
04：表示低级NPN开路输出, 使用A和B的脉冲输出信号;The number of pulses is 100PPR.
05：指示高级PNP源输出, 使用A和B的脉冲输出信号; The number of pulses is 100PPR.
③：代表轴选择开关的数量, 2 代表 2 axes.
④：代表轴选择开关信号类型, A表示点对点输出信号, and B represents encoded output signal.
⑤：代表乘法开关信号的类型, A表示点对点输出信号, and B represents encoded output signal.
⑥：代表自定义按钮的数量, 2 代表 2 custom buttons.
⑦：代表系统手轮的电源, 和 05 represents 5V power supply.
⑧：L代表左列 (左刀架), R代表右列 (右刀架).

9.产品故障解决方案

10. 产品维护

1. Please use it in a dry environment at room temperature and pressure to extend its service life.
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life.
3. Please keep the appearance of the handwheel clean to extend its service life.
4. 请避免挤压, 跌倒, 碰撞, ETC. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. 如果很长一段时间没有使用, 请将手轮存放在干净安全的地方. 在存储和运输过程中, attention should be paid to moisture and shock resistance.

11. 安全信息

1. Please read the instructions carefully before use and prohibit non professionals from operating.
2. Please replace the battery in a timely manner when the battery level is too low to avoid errors caused by insufficient battery power and inability to operate the handwheel.
3. 如果需要维修, 请联系制造商. 如果损害是由自修理造成的, 制造商将不提供保修

]]> Fanuc专用无线电子手轮 https://www.wixhc.cn/product/fanuc-dedicated-wireless-electronic-handwheel Tue, 06 May 2025 07:26:48 +0000 https://www.wixhc.cn/?post_type=product&p=4626

1.产品简介

无线电子手轮用于手动指导, 定位, 工具对齐,以及CNC机床上的其他操作. 该产品采用无线传输技术, 消除传统的弹簧电线连接, 减少电缆引起的设备故障, 消除电缆拖动和石油污渍的缺点, 并使操作更加方便. 这种无线电子手轮的模型是Fanuc系统的专用手轮. FANUC系统坐标通过IO-Link协议实时在手轮屏幕上实时显示, 和轴选择,放大, 和按钮信号通过IO-Link协议直接连接到系统, reducing wiring.

2. 产品功能
1. 采用433MHz无线通信技术, 无线操作距离为 40 仪表;
2. 采用自动跳跃功能, 使用 32 同时又不影响彼此的无线遥控器;
3. 支持紧急停止按钮, 切换IO信号输出, 通过IO接线连接到系统;
4. 支持 4 自定义按钮, 切换IO信号, 通过IO-Link协议向系统输出信号;
5. 支持快速移动按钮 + 和按钮 -, 按住按钮更换手轮以移动机器;
6. 支持6轴控制, 切换IO信号, 通过IO-Link协议向系统输出信号;
7. 支持1倍,10x, 100X控件 . 支持开关L0信号, 并通过IO-Link协议向系统输出信号;
8. 支持启用按钮功能, 通过IO接线连接到系统, 和控制编码器同时启用;
9. 支持脉冲编码器, 100 脉冲/圆, 通过输出AB编码信号访问系统MPG手轮接口;

3.产品规格

4.产品功能

笔记:
①施加停止按钮:
按下紧急停止按钮, 接收器上的两个紧急停止IO输出已断开连接, 所有手轮功能都无效。紧急停止释放后, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②屏幕显示:

Custom按钮:
4 自定义按钮, 每个按钮对应于接收器上的IO输出点, 通过IOLINK连接到系统. 一般来说, the ~ button is set as a high-speed button.
④轴选择开关:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
shortcut按钮:
按快捷按钮“+”将机器向前移动, 然后按捷切按钮“ - ”以消极地移动机器. This can replace turning the hand wheel to move the machine.
⑥启用按钮:
按住两侧的任何一个启用按钮，然后摇动脉冲编码器以有效. 并且接收器上的两组启用IO输出已打开. Release the enable button and the enable IO output is disconnected.
ratio开关:
Switching the magnification switch can switch the magnification of handwheel control.
⑧渗透编码器:
按住启用按钮并摇动脉搏编码器以发送脉冲
signal to control the movement of the machine axis.
⑨功率开关:
Handwheel power button.

5.产品配件图

6.产品安装指南

6.1 产品安装步骤

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.请参阅我们的接收器接线图, 将其与您的现场设备进行比较, 并连接
the equipment to the receiver via cables.
3. 接收器修复后, 配备了接收器的天线必须连接,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
建议将其放在电柜的顶部以获得最佳信号效果. 它
禁止将天线保持无连接或将天线放在电柜内,
which may cause the signal to be unusable.
4.最后, 打开手轮动力开关，您可以通过
handwheel remote control.

6.2 接收器安装尺寸

6.3 接收器接线参考图

7. 维护和关怀

1. 请在正常温度和压力的干燥环境中使用它以扩展
服务寿命;
2. 请避免在雨水和水泡等异常环境中使用它以扩展
服务寿命;
3. 请保持手轮清洁以延长使用寿命;
4. 请避免挤压, 跌倒, 碰撞, ETC. 为了防止损坏精度零件
在手轮中或导致精确错误;
5. 如果很长一段时间没有使用, 请将手轮存放在干净安全的地方;
6. Pay attention to moisture and shock during storage and transportation.

8. 安全信息

1. 请在使用前仔细阅读说明. 禁止非专业人士
operating.
2. 当电池太低以避免造成的错误时，请及时更换电池
insufficient power causing the handwheel to be unable to operate.
3. 如果需要维修, 请联系制造商. 如果损害是由自我修复造成的,
the manufacturer will not provide warranty.

]]> 西门子专用无线电子手轮XWGP-et https://www.wixhc.cn/product/siemens-dedicated-wireless-electronic-handwheel-xwgp-ets Thu, 26 May 2022 02:33:53 +0000 https://www.wixhc.cn/?post_type=product&p=4381

1.Introduction of remote control

a.Product Composition
Siemens real-time coordinate display wireless electronic handwheel consists of two parts: 电子手轮 + receiver;

b.Characteristics

*支持西门子PLC: S7-200/-300/-1200；支持西门子系统坐标值的实时显示；
*无线传输距离开放 40 仪表, automatic frequency hopping technology, can use 32 sets of equipment at the same time;
*The electronic handwheel is powered by 2 AA batteries and can be used for more than 30 天;
*The receiver is equipped with an external antenna to enhance the signal and is easy to install;
*Electronic handwheel support: 一个100ppr编码器 、一个6速轴选择开关 、 一个三速放大开关;
*Electronic handwheel supports 6 自定义按钮, corresponding to Siemens PLC address, 可以自由编程;

*6 自定义按钮可以控制 6 开关输出;
*The display screen displays the PLC corresponding register coordinate value in real time, and supports 6-axis display of real-time coordinates.

2.Application field

Programmable CNC remote control is widely used in various CNC fields such as laser engraving system, CNC铣床, CNC加工中心, gantry machine tool, ETC。

3. Introduction to the working principle

1）Electronic handwheel is connected to PLC via Ethernet receiver

a.The handwheel transmits the key data wirelessly to the receiver, and the receiver writes the keys through the network cable PLC system DB area; the receiver reads the data to be displayed from the designated DB area, and then returns the data to the handwheel display screen. The user can customize the base address of reading and writing DB area on the handwheel, so that the handwheel can read and write the data in the DB area of the PLC.

b. The receiver supports Siemens S7 protocol. Applies to PLC S7-200, PLC S7-300 and PLC S7-1200.

c. The user can configure the receiver to server mode and client mode through the PLC connection configuration tool.

In the server mode, the user configures the PLC read and write address through the WGP-ETS configuration software;Use the PLC connection configuration tool to configure the receiver into client mode. After configuration, the XWGP-ETS receiver can communicate with the PLC through the standard S7 protocol.

2)Specific application

Specific application of handwheel receiver and Siemens PLC S7-200:

a. The button on the handwheel corresponds to the value of the BOOL area set by the user in the PLC. If the button of the handwheel is pressed, the corresponding BOOL area is true, and when it is released, it is false, and the base address of the BOOL area can be set through the handwheel;

b. The handwheel can read the value of the DB area in the PLC. One axis has 4 bytes of display data, 和 6 axes have a total of 24 bytes. The base address of the DB area can be set through the WGP-ETS configuration software.

4.Appearance introduction

5.Receiver terminal definition and coding table

6.Appearance size

 

 

]]>