Traadimasin automaatne lõikamine traadita kaugjuhtimispuldi DH12S-P6S

Kirjeldus

1.Toote mudel

Mudel: DH12S-P6S

Kohaldatav varustus:wire saw/blade saw machine

2.Tootetarvikute skeem

Märkus: Saate valida ühe kolmest antennist. Iminapa antenn on vaikimisi standardvarustuses.

3.Kaugjuhtimispuldi lüliti kirjeldus

4.Kuva sisu tutvustus

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parameetrid reguleeritavad)
Automatic cutting main motor setting current: Setting: 28 (parameetrid reguleeritavad)
Swing arm motor speed: Swing: 0-50

Madal pinge: Kaugjuhtimispuldi patarei on liiga tühi, palun vahetage aku välja.

Võrk langes: Juhtmeta signaal on katkenud. Kontrollige vastuvõtja võimsust, lülitage see uuesti sisse, ja taaskäivitage kaugjuhtimispult.

5.Kaugjuhtimispuldi funktsioonide kasutusjuhised

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, lülitage toitelüliti sisse, and the display will show the motor speed, mis näitab edukat käivitamist.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, keerake “Edasi/tagasi” lülituda edasi, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, keerake “Edasi/tagasi” lülituda tagasikäigule, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Pöörake “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, keerake “Edasi/tagasi” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Pöörake “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” lüliti, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Vajutage ja hoidke all nuppu “speed adjustment enable” nuppu ja pöörake nuppu “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “edasi/tagasi” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (kasutajatel on keelatud seda ilma loata muuta)

Enter the parameter menu:Manuaalrežiimis, when the main motor speed is 0, lükake edasi/tagasi lüliti kolm korda järjest üles, and then push it down three times in a row to enterthe parameter menu;
Väljuge parameetrite menüüst: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, täitmata jätmine 800, unit milli second,muutmine on keelatud;
Aeglustumisparameeter: Kui lõikevoolu muutuse väärtus ületab selle väärtuse, rapid deceleration begins, unit Ampere;
Kiirendus A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Aeglustumine A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, muutmine on keelatud;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, muutmine on keelatud;
Maksimaalne vool: The range of main motor feedback current, unit Ampere;
Maksimaalne host: Remote control main motor speed adjustment display range;
Maksimaalne kõndimine: Invalid parameter;
Kiirusepiirangu nihe: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automaatne lõikamine, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;ühik: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Kaugjuhtimispuldi elektrilised omadused

7.Kaugjuhtimispuldi suurus

Selle toote lõplik tõlgendamisõigus kuulub ainult meie ettevõttele.