Tuki 4 mukautettuja painikkeita, Vaihda IO -signaali, Lähtösignaali järjestelmään IO-LINK-protokollan kautta;
Tukea nopeaa liikepainiketta + ja painike -, Paina painiketta vaihtamalla käsikirjoitus siirtämään koneen;
1.Tuotteen esittely
Wireless electronic handwheel is used for manual guidance, positioning, tool alignment,and other operations on CNC machine tools. This product adopts wireless transmission technology, eliminating the traditional spring wire connection, reducing equipment failures caused by cables, eliminating the disadvantages of cable dragging and oil stains, ja helpottaa käyttöä. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.
2. Tuotteen ominaisuudet
1. Hyväksy 433MHz langaton viestintätekniikka, Langaton käyttöetäisyys on 40 metriä;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the same time without affecting each other;
3. Support emergency stop button, Vaihda IO -signaalin lähtö, connected to the system through IO wiring;
4. Tuki 4 mukautettuja painikkeita, Vaihda IO -signaali, Lähtösignaali järjestelmään IO-LINK-protokollan kautta;
5. Tukea nopeaa liikepainiketta + ja painike -, Paina painiketta vaihtamalla käsikirjoitus siirtämään koneen;
6. Tukea 6-akselin hallinta, Vaihda IO -signaali, Lähtösignaali järjestelmään IO-LINK-protokollan kautta;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;
3.Product Specifications
4.Product Features
Muistiinpanot:
①Emergency stop button:
Press the emergency stop button, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.
②Screen display:
③Custom Buttons:
4 mukautettuja painikkeita, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.
5.Tuotteen lisävarustekaavio
6.Tuoteasennusopas
6.1 Product Installation Steps
1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Refer to our receiver wiring diagram, compare it with your on-site equipment, and connect
the equipment to the receiver via cables.
3. After the receiver is fixed, the antenna equipped with the receiver must be connected,
and the outer end of the antenna must be installed or placed outside the electrical cabinet.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. It
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
which may cause the signal to be unusable.
4.Finally, turn on the handwheel power switch and you can operate the machine by
handwheel remote control.
6.2 Receiver installation dimensions
6.3 Receiver Wiring Reference Diagram
7. Ylläpito ja hoito
1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
Palveluelämä;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. Please avoid squeezing, falling, bumping, jne. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. Jos sitä ei käytetä pitkään, please store the handwheel in a clean and safe place;
6. Pay attention to moisture and shock during storage and transportation.
8. Security Information
1. Lue ohjeet huolellisesti ennen käyttöä. Ei-ammattilaisia on kielletty
käyttö-.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. Jos korjausta vaaditaan, Ota yhteyttä valmistajaan. Jos vaurio aiheuttaa itsekorjauksen,
Valmistaja ei anna takuuta.
