Mesin gergaji kawat crawler otomatis remote control dh12s-ld

Keterangan

Model produk

Model: DH12S-LD

Peralatan yang berlaku:crawler wire saw machine

Diagram aksesori produk

Catatan: Anda dapat memilih salah satu dari tiga antena. Antena mangkuk isap adalah standar secara default.

Deskripsi saklar kendali jarak jauh

Tampilkan pengenalan konten

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameter dapat disesuaikan)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)

Tegangan rendah: Baterai kendali jarak jauh terlalu lemah, tolong ganti baterainya.

Jaringan terputus: Sinyal nirkabel terputus. Silakan periksa kekuatan penerima, nyalakan lagi, dan mulai ulang kendali jarak jauh.

Petunjuk pengoperasian fungsi kendali jarak jauh

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, nyalakan saklar daya, andthe display will show the motor speed, menunjukkan permulaan yang sukses.

2.Large motor and speed regulation

Putar “maju/mundur” beralih ke maju, the receiver’s large motor will turn on, and the display will show forward

Putar “maju/mundur” beralih ke mundur, the large motor of the receiver will turn on in reverse, and the display will show reverse

Putar “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “maju/mundur” beralih ke maju, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Putar “Maju/Mundur” beralih ke mundur, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Putar “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Putar “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

Dalam mode manual:
Turn left in place: Tekan dan tahan “Enable” tombol, putar “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Tekan dan tahan “Enable” tombol, putar “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

In automatic mode: press and hold the “Enable” tombol dan putar “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.Pemotongan otomatis

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Dalam mode manual, press and hold the “Enable” tombol dan putar “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 ke 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (pengguna dilarang memodifikasinya tanpa izin)

Beberapa fungsi remote control dapat disesuaikan melalui parameter. Dalam mode manual, when the small motor speed S2 is 10, tekan tombol maju/mundur ke atas tiga kali berturut-turut, and then push it down three times in a row to enter the parameter menu;
Keluar dari menu parameter: memilih untuk menyimpan atau tidak menyimpan, then press the enable button to confirm the exit;
Arus maksimum: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, bawaan 800, modifikasi dilarang;
Parameter perlambatan: automatic cutting control parameter. Ketika nilai perubahan arus pemotongan melebihi nilai ini,deceleration begins.
Percepatan a1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Perlambatan a2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Berjalan maksimal: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Pengimbangan batas kecepatan: the maximum speed of the small motor during automatic cutting.
Tuan rumah maksimal: maximum speed of large motor.

Karakteristik kelistrikan kendali jarak jauh

Ukuran kendali jarak jauh

Hak interpretasi akhir dari produk ini hanya milik perusahaan kami.