Ji bo rêwerzên operasyona Lathe Vertical Remeless Dedicated

① Pulse encoder:
Bişkojka çalak bikirtînin û bigirin, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Low voltage alarm light, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Bişkojka rawestandina acîl bikirtînin, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (guhêrbar hêza):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, divê antenna ku bi wergirê ve girêdayî ye were girêdan, and the outer end of the antenna should be installed or placed outside the electrical cabinet. It is recommended to place it on the top of the electrical cabinet for the best signal effect. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Paşan, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Pîvanên sazkirinê yên wergirê

6.3 Receiver Wiring Reference Diagram

7. Product operation instructions
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, û
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Bingeha hevrêziyê hilbijêrin: Bişkojka çalak bikirtînin û bigirin, toggle the axis selection switch, and select the axis you want to operate.
3. Mezinkirina hilbijêre: Bişkojka çalak bikirtînin û bigirin, toggle the magnification switch,and select the desired magnification level.
4. Tevgera eksê: Bişkojka çalak bikirtînin û bigirin, guhêrbar hilbijartina eksê hilbijêre, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Bişkojkek xwerû bikirtînin û bigirin, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Bişkojka rawestandina acîl bikirtînin, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. Ger çerxa destan ji bo demekê neyê xebitandin, it will automatically enter sleep mode to reduce power consumption. Dema ku ew dîsa tê bikaranîn, the handwheel can be activated by pressing the enable button.
8. Ger çerxa destan ji bo demek dirêj neyê bikar anîn, it is recommended to switch the handwheel shaft to the OFF position, hêza handwheel vekin, û jiyana pîlê dirêj bikin.

8. Danasîna Modela Hilberê

① :ZTWGP represents the appearance style
②：Parametreyên deranîna Pulse:
01: Indicates that the pulse output signal is A, B; Pulse voltaja 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Pulse voltaja 5V; pulse quantity 100PPR.
04：NPN-a-asta nizm derketinek dorhêla vekirî nîşan dide, bi sînyalên derana nebza A û B;The number of pulses is 100PPR.
05：Derketina çavkaniya PNP-a asta bilind destnîşan dike, bi sînyalên derana nebza A û B; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 temsîl dike 2 axes.
④：Represents the type of axis selection switch signal, A nîşana derana xal-bi-xala temsîl dike, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, A nîşana derana xal-bi-xala temsîl dike, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 temsîl dike 2 Bişkojkên xwerû.
⑦：Represents the power supply for the system handwheel, û 05 dabînkirina hêzê ya 5V temsîl dike.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions