Support 4 consuetudo bullarum, SWITCH IO signum, output signum ad systema per io link protocol;
Support Velox motus button + et button -, Torcular et teneat ipsum reponere Handwheel movere machina;
1.Product Introduction
Wireless Electronic Handwheel adhibetur ad manual duce, positus, tool alignment,and other operations on CNC machine tools. Hoc productum adoptat wireless tradenda technology, Eliminating in traditional vere filum nexu, Reducing apparatu defectis per cables, eliminating the disadvantages of cable dragging and oil stains, et faciens operationem commodius. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.
2. Product Features
1. 433MHz adopt Wireless Communication Technology, Wireless operatio procul est 40 metris;
2. Adopt automatic frequency hopping function, use 32 sets of wireless remote controllers at the same time without affecting each other;
3. Support emergency stop button, SWITCH IO signum output, connected to the system through IO wiring;
4. Support 4 consuetudo bullarum, SWITCH IO signum, output signum ad systema per io link protocol;
5. Support Velox motus button + et button -, Torcular et teneat ipsum reponere Handwheel movere machina;
6. Support VI, axis imperium, SWITCH IO signum, output signum ad systema per io link protocol;
7. Support 1X,10x*, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;
3.Product Specifications
4.Product Features
Notae:
①Emergency stop button:
Press the emergency stop button, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.
②Screen display:
③Custom Buttons:
4 consuetudo bullarum, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Torcular et tenere enable puga pyga et pulsus encoder mittere pulsus
Signum ad imperium motus ex machina axis.
⑨Power switch:
Handwheel power button.
5.Product accessiones tabulae
6.Product Installation Guide
6.1 Product installation gradus
1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.Refer ad receptaculum Wiring Diagram, Compare cum vestris on-site apparatu, et coniungere
Et apparatu ad recipiens per cables.
3. Post receptam fixa, In antenna instructa cum recipientis est connected,
et extrema Antennae esse installed vel extra electrica scrinium.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. Eam
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
quae potest facere signum inutile.
4.Tandem, Turn in Handwheel Power Switch et vos can operari machina a
Handwheel remote control.
6.2 Receptor installation dimensiones
6.3 Receptor Wiring reference Diagram
7. Tutela et cura
1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
in servitio vitae;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. Please avoid squeezing, falling, bumping, etc.. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. Si non diu usus est, please store the handwheel in a clean and safe place;
6. Pay attention to moisture and shock during storage and transportation.
8. Security Information
1. Lege diligenter ante usum instructiones. Non professionales prohibentur
operans.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. Nisi interdum sit, placere contactus corporis fabrica. Si damnum est causa per auto-reparatione,
fabrica non providere warantiam.
