Mamao Ahokore mo te Ahokore mo nga Taha Poari CNC

① Pulse encoder:
Pēhi me te pupuri i te pātene Whakahohe, Wiri i te kaimau pulse, Te whakaputa i tetahi tohu Pulse,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: He iti te marama whakaohooho, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Pēhi i te pātene aukati ohorere, me nga huinga e rua o te wa ohorere o te aukati io i te kaiwhiwhi ka whakakorehia, me nga mahi katoa o te ringaringa ka kore e tika.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (Huringa Poto):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, ia tangata e hāngai ana ki te wāhi putanga IO ki te kaiwhiwhi.

1. Tāutahia te kaiwhiwhi ki te rūnanga hiko na roto i te maaka i te taha o muri, Ka whakauruhia ranei ki roto i te rūnanga na roto i nga kohinga whiu i nga kokonga e wha o te kaiwhiwhi.
2. Tirohia ki to maatau kaiwhiwhi i te hoahoa me te whakataurite i o taputapu taputapu-a-papa. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, Ko te antena e rite ana ki te kaiwhiwhi me hono, and the outer end of the antenna should be installed or placed outside the electrical cabinet. E taunaki ana kia whakatakotoria ki runga i te tihi o te rūnanga hiko mo te paanga tohu pai. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. Rawa, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Nga Taumata Whakauru

6.3 He hoahoa tohutoro a te kaiwhiwhi

7. Tohutohu Mahi Hua
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, me
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. Tīpakohia te toki whakarite: Pēhi me te pupuri i te pātene Whakahohe, toggle the axis selection switch, and select the axis you want to operate.
3. Tīkina te whakanui: Pēhi me te pupuri i te pātene Whakahohe, toggle the magnification switch,and select the desired magnification level.
4. Neke toki: Pēhi me te pupuri i te pātene Whakahohe, Tīpakohia te huringa whiriwhiri Axis, Tīpakohia te whakawhiti whakanui, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. Pēhi me te pupuri i tetahi pātene ritenga, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Pēhi i te pātene aukati ohorere, Ko te aukati i te aukati i te whakaputanga o te kaiwhiwhi ka whakakorehia, Ka monokia te mahi a-ringa,Tukuna te pātene aukati ohorere, Ka kati te putanga ohorere io, Na ka whakahokia mai te mahi a-ringa.
7. Mena kaore i te whakahaerehia te ringaringa mo te waa roa, it will automatically enter sleep mode to reduce power consumption. Ka whakamahia ano hoki, the handwheel can be activated by pressing the enable button.
8. Mena kaore i te whakamahia te ringaringa mo te wa roa, it is recommended to switch the handwheel shaft to the OFF position, whakaweto i te mana ringaringa, ka whakawhānui i te ora pākahiko.

8. Whakaahuatanga Tauira Hua

① :ZTWGP represents the appearance style
②：Ko nga tohu whakaputa whakaputa:
01: Indicates that the pulse output signal is A, B; Pulse Lolgal 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Pulse Lolgal 5V; pulse quantity 100PPR.
04：E whakaatu ana i te putanga-tuwhera o te Taumata Taumata-iti, me nga tohu putanga Pulse o A me B;The number of pulses is 100PPR.
05：E whakaatu ana i te putanga PNP nui-taumata, me nga tohu putanga Pulse o A me B; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 tohu 2 oka.
④：Represents the type of axis selection switch signal, He tohu tohu tohu-ki-tohu, me te B e tohu ana i te tohu whakauru whakauru.
⑤：Represents the type of multiplication switch signal, He tohu tohu tohu-ki-tohu, me te B e tohu ana i te tohu whakauru whakauru.
⑥：Represents the number of custom buttons, 2 tohu 2 pātene ritenga.
⑦：Represents the power supply for the system handwheel, me 05 tohu mo te 5V mana mana.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions