Wire saw machine automatic cutting wireless remote control DH12S-P6S

Tavsif

1.Mahsulot modeli

 

Model: DH12S-P6S

Qo'llaniladigan uskunalar:wire saw/blade saw machine

2.Mahsulot uchun aksessuarlar diagrammasi

Eslatma: Siz uchta antennalardan birini tanlashingiz mumkin. Assimilyatsiya kubogi antenna sukut bo'yicha standart hisoblanadi.

3.Masofadan boshqarish pulti Tasvir tavsifi

4.Discondentni kiritish

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(parametrlar sozlanishi)
Automatic cutting main motor setting current: Setting: 28 (parametrlar sozlanishi)
Swing arm motor speed: Swing: 0-50

Kam kuchlanish: Masofadan boshqarish pulti batareyasi juda past, Iltimos batareyani almashtiring.

Tarmoq tushdi: Simsiz signal to'xtatiladi. Iltimos, qabul qilgichning quvvatini tekshiring, uni yana yoqing, va masofadan boshqarish pultini qayta ishga tushiring.

5.Masofadan boshqarish funktsiyasi operatsiya ko'rsatmalar

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, Quvvat tugmachasini yoqing, and the display will show the motor speed, Muvaffaqiyatli ishga tushirish.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, burilmoq “Oldinga / teskari” Oldinga o'tish, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, burilmoq “Oldinga / teskari” teskari tomonga o'tish, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Aylantiring “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, burilmoq “Oldinga / teskari” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Burilmoq “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Ni bosing va ushlab turing “speed adjustment enable” tugmasini bosing va aylantiring “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “oldinga / teskari” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (Foydalanuvchilar ruxsatsiz o'zgartirish taqiqlanadi)

Enter the parameter menu:Qo'l rejimida, when the main motor speed is 0, oldinga / teskari tugmachani ketma-ket uch marta bosing, and then push it down three times in a row to enterthe parameter menu;
Parametr menyusidan chiqing: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, bajarilish 800, unit milli second,o'zgartirish taqiqlanadi;
Dreatsion parametr: Kesish oqim o'zgarishi qiymati ushbu qiymatdan oshganda, rapid deceleration begins, unit Ampere;
A1 ni tezlashtirish: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
A2 ni sekinlashtirish: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, o'zgartirish taqiqlanadi;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, o'zgartirish taqiqlanadi;
Maksimal oqim: The range of main motor feedback current, unit Ampere;
Maksimal xost: Remote control main motor speed adjustment display range;
Maksimal yurish: Invalid parameter;
Tezlik chegarasi ofset: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Avtomatik kesish, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Masofadan boshqarish pulti elektr xususiyatlari

7.Masofadan boshqarish hajmi

Ushbu mahsulotning yakuniy talqini faqat bizning kompaniyamizga tegishli.