申請:專用於爬行線鋸機
1.Supports automatic cutting function, automatically adjusts cutting speed according to motor current feedback
2.冇障礙傳輸距離係 200 米.
3. Support DC driver.
4. Supports multiple cutting parameter settings, such as cutting current, cutting speed limit, 等等.
5. Supports switching between wire saw and blade saw modes. Different cutting parameters can be set in different modes.
模型: DH12S-P6S
適用設備:wire saw/blade saw machine
筆記薄: 你可以揀三個天線之一. 吸盤天線預設係標準.
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(參數可調節)
Automatic cutting main motor setting current: Setting: 28 (參數可調節)
Swing arm motor speed: Swing: 0-50
低電壓: 遙控電池太低, 請換電池.
網絡掉落: 無線訊號中斷. 請檢查接收器嘅力量, 再次開機, 同埋重新啟動遙控器.
1）Turn on the remote control
When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, 開啟電源開關, and the display will show the motor speed, 表示成功嘅初創公司.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, 轉個 “前進 / 逆向” 轉用向前, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, 轉個 “前進 / 逆向” 轉用反轉, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;旋轉個 “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, 轉個 “前進 / 逆向” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
轉咗個 “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
按住個 “speed adjustment enable” 按鈕，然後旋轉 “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “向前 / 逆轉” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (使用者喺未經許可嘅情況下，就禁止修改呢個功能)
Enter the parameter menu:係手動模式下, when the main motor speed is 0, 連續三次推向前 / 反向開關, and then push it down three times in a row to enterthe parameter menu;
退出參數選單: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, 預設 800, unit milli second,禁止修改;
減速參數: 當切割電流變化值超過呢個值, rapid deceleration begins, unit Ampere;
加速 a1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
減速 a2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, 禁止修改;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, 禁止修改;
最大電流: The range of main motor feedback current, unit Ampere;
最大主機: Remote control main motor speed adjustment display range;
最大行路: Invalid parameter;
速度限制偏移: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: 自動切割, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
呢個產品嘅最後解釋權只係屬於我哋公司.
