FANUC 專用無線電子手輪

描述

1.產品介紹

無線電子手輪用於手動指導, 定位, tool alignment,and other operations on CNC machine tools. 本產品採用無線傳輸技術, 消除傳統彈簧線連接, 減少電纜引起嘅設備故障, eliminating the disadvantages of cable dragging and oil stains, and making operation more convenient. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. 產品功能
1. 採用 433MHZ 無線通訊技術, 無線操作距離係 40 米;
2. 採用自動跳跳功能, 使用 32 sets of wireless remote controllers at the same time without affecting each other;
3. 支援緊急停止掣, 開關 IO 訊號輸出, connected to the system through IO wiring;
4. 支持 4 自訂掣, switch IO signal, output signal to the system through IO-LINK protocol;
5. Support quick movement button + and button -, press and hold the button to replace the handwheel to move the machine;
6. 支援 6 軸控制, switch IO signal, output signal to the system through IO-LINK protocol;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

筆記:
① 緊急停止按鈕:
按緊急停止按鈕, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 自訂掣, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
按住啟用按鈕，然後搖晃脈衝編碼器，以便發送脈衝
訊號要控制機器軸嘅移動.
⑨Power switch:
Handwheel power button.

5.產品配件圖

6.產品安裝指南

6.1 產品安裝步驟

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.請參閱我哋嘅接收器接線圖, 將佢同你嘅現場設備比較, 同埋連接
透過電纜向接收器嘅設備.
3. 接收器固定後, 配備接收器嘅天線必須連接,
而天線嘅外端就要安裝或者放喺電器櫃外面.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. 佢
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
呢個可能會令訊號無法使用.
4.最終, 開手輪電源開關，你可以由機操作
手輪遙控器.

6.2 接收器安裝尺寸

6.3 接收器接線參考圖

7. 維修同照顧

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
使用生活;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. 請避免擠壓, 跌咗, 碰撞, 等等. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. 如果唔用好耐, 請將手輪儲存係乾淨安全嘅地方;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. 使用前請仔細閱讀指示. 非專業人士係禁止嘅
運作.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. 如果需要維修, 請聯絡廠商. 如果損害係由自我修復引起,
廠商唔會提供保養.