專用無線遙控器進行數控垂直車床操作指令

① Pulse encoder:
按住啟用掣, shake the pulse encoder, emit a pulse signal,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Low voltage alarm light, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
按緊急停止按鈕, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (電源開關):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, each corresponding to an IO output point on the receiver.

1. Install the receiver into the electrical cabinet through the buckle on the back, or install it into the cabinet through the screw holes at the four corners of the receiver.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, 配備接收器嘅天線必須連接, and the outer end of the antenna should be installed or placed outside the electrical cabinet. 建議將佢放係電櫃頂部，以獲得最佳訊號效果. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. 最終, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 接收器安裝尺寸

6.3 接收器接線參考圖

7. Product operation instructions
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, 同
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. 選擇座標軸: 按住啟用掣, toggle the axis selection switch, and select the axis you want to operate.
3. 揀放大: 按住啟用掣, toggle the magnification switch,and select the desired magnification level.
4. 移動軸: 按住啟用掣, 選擇軸選擇開關, select the magnification switch, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. 按住任何自訂掣, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. 按緊急停止按鈕, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled,release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
7. 如果手輪係一段時間唔操作, it will automatically enter sleep mode to reduce power consumption. 當佢再用嘅時候, the handwheel can be activated by pressing the enable button.
8. 如果手輪唔用好耐, it is recommended to switch the handwheel shaft to the OFF position, 熄手輪功率, 同埋延長電池壽命.

8. 產品模型描述

① :ZTWGP represents the appearance style
②：脈衝輸出參數:
01: Indicates that the pulse output signal is A, B; 脈衝電壓 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; 脈衝電壓 5V; pulse quantity 100PPR.
04：表示低層次 NPN 開放電路輸出, 有脈搏輸出訊號 A 及 B;The number of pulses is 100PPR.
05：表示高層次 PNP 源輸出, 有脈搏輸出訊號 A 及 B; The number of pulses is 100PPR.
③：Representing the number of axis selection switches, 2 代表 2 axes.
④：Represents the type of axis selection switch signal, A 代表點對點輸出訊號, and B represents encoded output signal.
⑤：Represents the type of multiplication switch signal, A 代表點對點輸出訊號, and B represents encoded output signal.
⑥：Represents the number of custom buttons, 2 代表 2 自訂掣.
⑦：Represents the power supply for the system handwheel, 同 05 代表 5V 電源.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions