1. Use a 6-core aviation plug cable for connection, with a handwheel cable length of 10 米.
2. The handwheel screen can display system workpiece coordinates, mechanical coordinates,feed rate, 軸選擇, 放大, and other information.
3. 支援緊急停止掣, 開關 IO 訊號輸出, and the hand wheel shutdown emergency stop is still valid.
4. 支持 6 自訂掣, switch IO signals, and can output signals to the system through IO wiring or communication.
有線電子手輪指示手冊
描述
1. 產品介紹
Electronic handwheel is used for manual guidance, 定位, 工具對齊, 同埋其他喺數控機床上面嘅操作. This model of electronic handwheel is a Siemens actual display wired electronic handwheel. The handwheel is connected to the X130 interface of the Siemens system through a network cable, and the system coordinates are read and displayed on the LCD screen of the handwheel through S7 protocol communication. The handwheel can also control system axis selection, 放大, buttons, andother signals through communication.
2.Product functional features
1. Use a 6-core aviation plug cable for connection, with a handwheel cable length of 10 米.
2. The handwheel screen can display system workpiece coordinates, mechanical coordinates,feed rate, 軸選擇, 放大, and other information.
3. 支援緊急停止掣, 開關 IO 訊號輸出, and the hand wheel shutdown emergency stop is still valid.
4. 支持 6 自訂掣, switch IO signals, and can output signals to the system through IO wiring or communication.
5. 支持 6 或者 8 軸控制, with switch IO signals that can be output to the system through IO wiring or communication.
6. 支持 3 或者 4 levels of magnification control, with switch IO signals that can be output to the system through IO wiring or communication.
7. 支援脈衝編碼器, 100 脈衝 / 轉, can output signals to the system through AB pulse wiring.
8. Supports Siemens S7 protocol and Siemens 828D, 840DSL, ONE and other model systems.
3. 產品規格
| Handwheel working power supply voltage | DC24V/1A |
| Receiver power supply voltage | DC24V/1A |
| Receiver IO output load range | DC24V |
| Hand wheel end cable length | 10m |
| Receiver end cable length | 1m |
| Receiver end network cable length | 3m |
| Operating temperature | -25℃<X<55℃ |
| Anti-fall height | 1m |
| Custom Button Quantity | 6 |
| Product dimensions | 233*90.7*77.4（mm） |
4.產品功能介紹
筆記薄:
Emergency stop button:
按緊急停止按鈕, and the two sets of emergency stop IO outputs on the receiver will be disconnected, and all functions of the handwheel will be invalid.
After releasing the emergency stop, 緊急停止 IO 輸出係接收器上關閉, and all functions of the handwheel are restored.
② Screen display:
PLC: 0000 indicates that the network cable is not connected, PLC: 1010 indicates that the network cable is successfully connected to the PLC system.
PLC: 1110 represents successful writing of system data to the handwheel, PLC: 0001 represents successful connection to the computer.
③ Custom button:
6 自訂掣, each corresponding to an IO output point on the receiver, also connected to the system through communication.
④ Axis selection switch:
The axis selection switch can switch the movement axis controlled by the handwheel.
⑤ Enable button:
Press and hold either enable button on both sides to activate the pulse encoder by shaking it. And the two groups on the receiver enable IO output to conduct, release the enable button to enable IO output to disconnect.
⑥ Magnification switch:The magnification switch can switch the magnification
controlled by the handwheel.
⑦ Pulse encoder:
按住啟用掣, shake the pulse encoder, emit a pulse signal, and control the movement of the machine axis.
⑧ Handwheel cable:
Cable connecting the handwheel and receiver, aviation plug, used for handwheel power supply and communication.
5. 產品配件圖
6. 產品安裝指南
6.1 Product installation steps
6.1 Product installation steps
1. Install the receiver into the electrical cabinet through the screw holes at the four corners.
2. Refer to our receiver wiring diagram and compare it with your on-site equipment. Connect the device to the receiver through cables and connect the receiver to the X130 interface of the system using Ethernet cables.
3. After fixing the receiver, install the aviation plug base at the handwheel opening position on the panel, and plug the other end of the base into the handwheel interface on the receiver. Then insert the aviation plug of the handwheel cable into the base and tighten the fixing device.
6.2 接收器安裝尺寸
6.3 Installation dimensions of aviation plugs
6.4 接收器接線參考圖
7.產品營運指示
7.產品營運指示
1. When the receiver is powered on and the working indicator light of the receiver flashes, connect the receiver to the computer with a network cable, set the fixed IP address of the computer, and use the network configuration tool software to set the network parameters of the handwheel function. For specific setting methods, refer to the “LXWGP-ETS Wired Handwheel User Manual”.
2.After the receiver is set up, the system needs to program a PLC program. Please refer to the “LXWGP-ETS Different Siemens Numerical Control System Setting Methods” and PLC program routine materials for details.
3.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X130 interface of the system.Connect the receiver power supply and pulse line.3.
4.After completing the above settings, take the receiver to the machine electrical cabinet and install it. Pull out the network cable from the computer and plug it into the X interface of the system. Connect the receiver power supply and pulse line.
5. Select axis selection: Switch the axis selection switch and select the axis you want to operate on.
6. 揀放大: Switch the magnification switch and select the magnification level you need.
7. 移動軸: 按住啟用掣, 選擇軸選擇開關, select the magnification switch, and then rotate the pulse encoder to rotate the positive moving axis clockwise and the negative moving axis counterclockwise.
8. Press and hold any custom button to turn on the IO output of the corresponding button in the receiver, and release the button to turn off the output.
9. 按緊急停止按鈕, the corresponding emergency stop IO output of the receiver will be disconnected, the handwheel function will be disabled, release the emergency stop button, the emergency stop IO output will be closed, and the handwheel function will be restored.
8.產品模型描述
① LXWGP represents a wired appearance style, and the receiver communication interface
is an Ethernet interface.
② : Represents Siemens system specific.
③ : 代表軸選擇開關數目, represents axes, and represents
axes.
④ : represents the type of axis selection and magnification signal, A represents
point-to-point output signal, and B represents encoded output signal.
9.Product trouble shooting
10.維護
1. 請於室溫下乾燥環境及壓力，延長使用壽命.
2. 請避免使用於雨水及水泡等異常環境，以延長使用壽命.
3. 請保持手輪外觀乾淨，以延長使用壽命.
4. 請避免擠壓, 跌咗, 碰撞, 等等. to prevent damage to the precision components inside the handwheel or accuracy errors.
5. 如果唔用好耐, please store the handwheel in a clean and safe place.During storage and transportation, 應該注意防潮同抗震.
11. 安全資訊
1. 使用前請仔細閱讀指示，並禁止非專業人士運作.
2. If any abnormal situation occurs with the handwheel, please stop using it immediately and troubleshoot. Before troubleshooting, it is forbidden to use the faulty handwheel again to avoid safety accidents caused by unknown handwheel faults;
3. 如果需要維修, 請聯絡廠商. 如果損壞係由自我修復引起, 廠商唔會提供保養
