Mesin Kawat Nganggo Crawler Kawat Translate Kontrol Jaringan Nirkabel kanthi otomatis Ngontrol DH12S-LD

Katrangan

Model Produk

Model: DH12S-LD

Peralatan sing ditrapake:crawler wire saw machine

Diagram aksesoris produk

Cathetan: Sampeyan bisa milih salah siji saka telung antena. Antena Piala Sukses minangka standar kanthi standar.

Katrangan Ngalih Kontrol Remot

Displaycontent introduction

Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (parameters adjustable)
Linear correction value: DF: -99-99 (1 unit is about 0.02V)

Tegangan sithik: Baterei kontrol remot kurang sithik, Mangga ngganti baterei.

Jaringan mudhun: Sinyal nirkabel diganggu. Mangga priksa kekuwatan panrima, kekuwatan maneh, lan miwiti maneh kontrol remot.

Pandhuan Operasi Fungsi Kontrol Remot

1.Turn on the remote control

When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, Nguripake saklar daya, andthe display will show the motor speed, nuduhake wiwitan sukses.

2.Large motor and speed regulation

Turn the “forward/reverse” switch to forward, the receiver’s large motor will turn on, and the display will show forward

Turn the “forward/reverse” switch to reverse, the large motor of the receiver will turn on in reverse, and the display will show reverse

Rotate the “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;

3.Small motor and speed regulation

Move the “forward/reverse” switch to forward, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward

Turn the “Forward/Reverse” switch to reverse, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse

4.Turn left and right

Turn the “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left

Turn the “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right

5.Turn in place

Ing mode manual:
Turn left in place: Press and hold the “Enable” Tombol, turn the “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;

Turn right in place: Press and hold the “Enable” Tombol, turn the “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;

6.Small motor speed limit adjustment

Ing mode otomatis: press and hold the “Enable” button and rotate the “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;

7.Automatic cutting

The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;

8. Straight line correction

When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: Ing mode manual, press and hold the “Enable” button and rotate the “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 menyang 90; correction voltage of one correction unit is about 0.02V;

9. Parameter menu (users are prohibited from modifying it without permission)

Sawetara fungsi kontrol remot bisa diatur liwat paramèter. Ing mode manual, when the small motor speed S2 is 10, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enter the parameter menu;
Metu menu paramèter: Pilih kanggo nyimpen utawa ora nyimpen, then press the enable button to confirm the exit;
Saiki maksimal: the operating rated current of the cutting motor is 80% of this currentt;
Paramèter kontrol kacepetan: automatic cutting control parameters, Default 800, modification is prohibited;
Parameter deceleration: automatic cutting control parameter. When the cutting current change value exceeds this value,deceleration begins.
Nyepetake A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
Deceleration A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
Maximum walking: the maximum speed of the small motor.
Nglereni Saiki: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Watesan kacepetan standar: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
Watesan watesan watesan: the maximum speed of the small motor during automatic cutting.
Host maksimal: maximum speed of large motor.

Karakteristik Listrik Kontrol Remot

Ukuran Kontrol Remot

Interpretasi pungkasan saka produk iki mung kanggo perusahaan kita.