Description
1.Modely vokatra
MODELY: DH12S-P6S
Fitaovana azo ampiharina:wire saw/blade saw machine
2.Ny sary miditra amin'ny vokatra
Fanamarihana: Azonao atao ny misafidy ny iray amin'ireo Antena telo. Ny Antenna Cup Suction dia fenitra amin'ny alàlan'ny default.
3.Famaritana Switch Switch
4.Fampidirana fampisehoana
Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(Parameter azo zahana)
Automatic cutting main motor setting current: Setting: 28 (Parameter azo zahana)
Swing arm motor speed: Swing: 0-50
Voltage ambany: Ny bateria fanaraha-maso lavitra dia ambany loatra, Azafady azafady ny bateria.
Nilatsaka ny tambajotra: Ny famantarana an-tariby dia tapaka. Azafady mba jereo ny herin'ilay mpandray, herim-po indray, ary avereno ny fanaraha-maso lavitra.
5.Fanaraha-maso ny fanaraha-maso lavitra
1）Turn on the remote control
When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, mihodina ny switch herinaratra, and the display will show the motor speed, manondro fanombohana mahomby.
2）Large motor and speed regulation/Main motor and speed regulation
Press and hold “Speed Regulation Enable”, avadika ny “Mandroso / mifamadika” Mihodinkodina amin'ny handroso, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, avadika ny “Mandroso / mifamadika” mifamadika amin'ny mifamadika, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;Hodio ny “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;
3）Traveling motor
Press and hold “Speed Adjustment Enable”, avadika ny “Mandroso / mifamadika” switch to forward or backward, and the walking motor will move at a high speed of 50;
4）Swing arm motor and speed regulation
Avadika ny “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;
Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;
5）Travel motor speed limit adjustment
Tsindrio ary mitazona ny “speed adjustment enable” bokotra ary rotate ny “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;
6） Automatic cutting
The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “mandroso / mifamadika” switch forward or backward to enter the automatic cutting mode;
7） Parameter menu (Ireo mpampiasa dia voarara tsy hanova azy raha tsy nahazoana alàlana)
Enter the parameter menu:Amin'ny fomba manual, when the main motor speed is 0, manosika ny handroso / avereno miverina intelo isaky ny laharana, and then push it down three times in a row to enterthe parameter menu;
Mivoaha ny menio Parameter: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, toerana misy anao 800, unit milli second,Voarara ny fanovana;
Fehezan-dalàna fametahana: Rehefa mihoatra ny sandany ity lafo vidy ity, rapid deceleration begins, unit Ampere;
Acceleration A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Seceleration A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, Voarara ny fanovana;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, Voarara ny fanovana;
Ny tena ambony indrindra: The range of main motor feedback current, unit Ampere;
Host-Hostur: Remote control main motor speed adjustment display range;
Mandeha ambony indrindra: Invalid parameter;
Fomba fanodinana hafainganam-pandeha: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Tapaka mandeha ho azy, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;
6.Toetr-toetra elektrika fanaraha-maso lavitra
7.Ny haben'ny fanaraha-maso lavitra
Ny zo fandikana farany amin'ity vokatra ity dia tsy ao amin'ny orinasanay fotsiny.
