Te mau a'oraa no ni'a i te CNC aita e aho no te mau faaueraa tumu CNC

① Pulse encoder:
A tape'a e a tape'a i te taviri e faati'a, parau, A faataa i te hoê tapao,and control the movement ofthe machine axis.
② Enable button:
Press either enable button on either side, and the two sets of enable IO outputs on the receiver will conduct. Release the enable button to disconnect the enable IO output; And before switching the axis selection magnification and shaking the handwheel,the enable button needs to be held down to be effective; This function can be cancelled through configuration software.

③ Indicator lights:
Left side light: power on light,the handwheel uses the axis to select OFF for power on, and this light stays on after power on;
Middle light: a signal light that lights up when operating any function ofthe handwheel, and does not light up when there is no operation;
Right side light: Low voltage alarm light, low battery level,this lightflashes or stays on, battery needs to be replaced.

④ Emergency stop button:
Tapa'o i te taviri no te tape'a i te mau fifi rû, e te mau faahopearaa o te mau IO i nia i te taata e farii ra, e tuatihia na pǔpǔ e piti, e e riro te mau ohipa atoa o te afata teata ei mea ino.

⑤ Magnification switch:
Press and hold the enable button to switch the magnification switch, which can switch the magnification controlled by the handwheel.

⑥ Axis selection switch (Riti):
Press and hold the enable button to switch the axis selection switch, which can switch the movement axis controlled by the handwheel. Switch this switch from OFF to any axis and turn on the handwheel power.

⑦ Custom button:
Two custom buttons, te mau mea atoa i nia i te hoê tuhaa hopea IO i nia i te taata farii.

1. A tuu i te taata farii i roto i te piha uira i nia i te vahi i muri, e aore râ, a tuu i te reira i roto i te piha na roto i te mau apoo pape i te mau poro e maha o te taata farii.
2. A hi'o i ta tatou hoho'a no te feia farii e a faaau i te reira i ta outou mau rave'a i ni'a i te tahua. Connect the equipment to the receiver via cables.
3.After the receiver is properly fixed, E mea ti'a ia tuati te antenna i te taata farii, and the outer end of the antenna should be installed or placed outside the electrical cabinet. Te faaitoitohia ra ia tuu i te reira i nia i te tumu o te piha uira no te hoê tapao maitai roa ' ' e. It is prohibited to leave the antenna unconnected or place it inside the electrical cabinet, as this may result in the signal being unusable.
4. ʻIa, turn on the power switch of the handwheel, and you can operate the machine remotely using the handwheel.

6.2 Te mau faito o te haamauraa i te mau mea

6.3 Hoho'a i papa'i

7. Te mau faaueraa
1. Power on the machine and the receiver. The receiver’s working indicator light flashes. Install the battery in the wireless electronic handwheel, secure the battery cover, e
turn on the power switch of the wireless electronic handwheel. The handwheel’s battery level indicator light is on.
2. A maiti i te tuhaa fenua: A tape'a e a tape'a i te taviri e faati'a, toggle the axis selection switch, and select the axis you want to operate.
3. A maiti i te faarahi i te faito: A tape'a e a tape'a i te taviri e faati'a, toggle the magnification switch,and select the desired magnification level.
4. Mā'oi: A tape'a e a tape'a i te taviri e faati'a, ma'iti i te tauiraa o te mau hu'ahu'a, ma'iti i te tauiraa o te faarahiraa, and then rotate the pulse encoder. Rotate clockwise to move the
positive axis and counterclockwise to move the negative axis.
5. A tape'a e a tape'a i te mau taviri atoa, and the corresponding button IO output of the receiver will be turned on. Release the button, and the output will be turned off.
6. Tapa'o i te taviri no te tape'a i te mau fifi rû, E tatarahia te vahi tapearaa IO o te taata farii, E faaorehia te ohipa a te tau faaeteete,A tatara i te taviri no te tape'a i te pape pu'e, E opanihia te mau faahopearaa o te IO, e e faaho'i-faahou-hia mai te ohipa a te tau.
7. Mai te mea e, aita te ahu o te rima e faaohipahia no te hoê tau, it will automatically enter sleep mode to reduce power consumption. Ia faaohipahia te reira, the handwheel can be activated by pressing the enable button.
8. Mai te mea e, aita te ahu o te rima e faaohipahia no te hoê tau maoro, it is recommended to switch the handwheel shaft to the OFF position, a taui i te mana o te rima, e e faarahi i te ora o te mori.

8. Te ti'a'o

① :ZTWGP represents the appearance style
⁡：Te mau faataaraa āra'a:
01: Indicates that the pulse output signal is A, B; Pulse ana'e 5V; pulse quantity 100PPR.
02：Indicating thatthe pulse output signals are A and B; Pulse voltage 12V; pulse quantity 100PPR.
03：Indicating thatthe pulse output signals are A, B, A -, B -; Pulse ana'e 5V; pulse quantity 100PPR.
04：E horo'a te reira i te hoê faanahoraa haereraa i mua no te hoê pereoo uira NPN, e te mau tapa'o hopea o te A e B;The number of pulses is 100PPR.
05：E faatupu te reira i te mau rave'a PNP teitei, e te mau tapa'o hopea o te A e B; The number of pulses is 100PPR.
faaafaro：Representing the number of axis selection switches, 2 fa'ahou 2 Pō'i.
④：Represents the type of axis selection switch signal, E faahoho'a te hoê i'oa i te tapa'o i te tapa'o, e B te faahoho'a ra i te tapao o te mau hu'ahu'a.
⑤：Represents the type of multiplication switch signal, E faahoho'a te hoê i'oa i te tapa'o i te tapa'o, e B te faahoho'a ra i te tapao o te mau hu'ahu'a.
⑥：Represents the number of custom buttons, 2 fa'ahou 2 tā'atira'a.
⑦：Represents the power supply for the system handwheel, e 05 te faaite ra i te mau ravea no te horoa i te puai 5V.
⑧：L represents the left column (left knife holder), and R represents the right column (right knife holder).

9.Solution to Product Malfunctions