Fanuc專用無線電子手輪

描述

1.產品簡介

無線電子手輪用於手動指導, 定位, tool alignment,and other operations on CNC machine tools. 該產品採用無線傳輸技術, 消除傳統的彈簧電線連接, 減少電纜引起的設備故障, eliminating the disadvantages of cable dragging and oil stains, and making operation more convenient. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. 產品功能
1. 採用433MHz無線通信技術, 無線操作距離為 40 儀表;
2. 採用自動跳躍功能, 使用 32 sets of wireless remote controllers at the same time without affecting each other;
3. 支持緊急停止按鈕, 切換IO信號輸出, connected to the system through IO wiring;
4. 支持 4 自定義按鈕, 切換IO信號, 通過IO-Link協議向系統輸出信號;
5. 支持快速移動按鈕 + 和按鈕 -, 按住按鈕更換手輪以移動機器;
6. 支持6軸控制, 切換IO信號, 通過IO-Link協議向系統輸出信號;
7. Support 1X,10x, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

筆記:
①施加停止按鈕:
按下緊急停止按鈕, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 自定義按鈕, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
按住啟用按鈕並搖動脈搏編碼器以發送脈衝
信號控制機器軸的運動.
⑨Power switch:
Handwheel power button.

5.產品配件圖

6.產品安裝指南

6.1 產品安裝步驟

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.請參閱我們的接收器接線圖, 將其與您的現場設備進行比較, 並連接
通過電纜到接收器的設備.
3. 接收器修復後, 配備了接收器的天線必須連接,
並且天線的外端必須安裝或放置在電櫃外面.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. 它
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
這可能導致信號無法使用.
4.最後, 打開手輪動力開關，您可以通過
手輪遙控器.

6.2 接收器安裝尺寸

6.3 接收器接線參考圖

7. 維護和關懷

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
服務壽命;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. 請避免擠壓, 跌倒, 碰撞, ETC. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. 如果很長一段時間沒有使用, 請將手輪存放在乾淨安全的地方;
6. Pay attention to moisture and shock during storage and transportation.

8. Security Information

1. 請在使用前仔細閱讀說明. 非專業人員禁止
操作.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. 如果需要維修, 請聯繫製造商. 如果是自行修理造成的損壞,
製造商將不提供保修.