FANUC dedicated wireless electronic handwheel

描述

1.产品介绍

无线电子手轮用于手动指导, 定位, tool alignment,and other operations on CNC machine tools. 该产品采用无线传输技术, 消除传统的弹簧电线连接, 减少电缆引起的设备故障, eliminating the disadvantages of cable dragging and oil stains, 并让操作更加便捷. This model of wireless electronic handwheel is a dedicated handwheel for the Fanuc system. The Fanuc system coordinates are displayed in real-time on the handwheel screen through the IO-LINK protocol, and the axis selection,magnification, and button signals are directly connected to the system through the IO-LINK protocol, reducing wiring.

2. 产品特点
1. 采用433MHZ无线通讯技术, 无线操作距离为 40 米;
2. 采用自动跳跃功能, 快速建站 32 sets of wireless remote controllers at the same time without affecting each other;
3. 支持紧急停止按钮, 开关量IO信号输出, connected to the system through IO wiring;
4. 支持 4 自定义按钮, switch IO signal, output signal to the system through IO-LINK protocol;
5. Support quick movement button + and button -, press and hold the button to replace the handwheel to move the machine;
6. 支持6轴控制, switch IO signal, output signal to the system through IO-LINK protocol;
7. Support 1X,10X, 100X control . Support switch l0 signal, and outputs signals to the system via IO-LINK protocol;
8. Support enable button function, connect to the system through IO wiring, and control encoder enable at the same time;
9. Support pulse encoder, 100 pulses/circle, access the system MPG handwheel interface by outputting AB encoding signal;

3.Product Specifications

4.Product Features

笔记:
①施加停止按钮:
按下紧急停止按钮, the two emergency stop IO outputs on the receiver are disconnected, and all handwheel functions are invalid.After the emergency stop is released, the emergency stop IO output on the receiver is closed and all functions of the handwheel are restored.

②Screen display:

③Custom Buttons:
4 自定义按钮, each button corresponds to an IO output point on the receiver, connected to the system through IOLINK. Generally, the ~ button is set as a high-speed button.
④Axis selection switch:
Switching the axis selection switch can switch the moving axis controlled by the handwheel.
⑤Shortcut buttons:
Press the shortcut button “+ ”to move the machine forward, and press the short cut button “-” to move the machine negatively. This can replace turning the hand wheel to move the machine.
⑥Enable button:
Press and hold any one of the enable buttons on both sides and shake the pulse encoder to be effective. And the two groups of enable IO outputs on the receiver are turned on. Release the enable button and the enable IO output is disconnected.
⑦Ratio switch:
Switching the magnification switch can switch the magnification of handwheel control.
⑧Pulse encoder:
Press and hold the enable button and shake the pulse encoder to send out a pulse
signal to control the movement of the machine axis.
⑨Power switch:
Handwheel power button.

5.产品配件图

6.产品安装指南

1. Install the receiver in the electrical cabinet through the screw holes at the four corners.
2.请参阅我们的接收器接线图, 将其与您的现场设备进行比较, 并连接
通过电缆到接收器的设备.
3. 接收器修复后, 配备了接收器的天线必须连接,
并且天线的外端必须安装或放置在电柜外面.
It is recommended to place it on the top of the electrical cabinet for the best signal effect. 它
is prohibited to leave the antenna unconnected or place the antenna inside the electrical cabinet,
这可能导致信号无法使用.
4.最后, 打开手轮动力开关，您可以通过
手轮遥控器.
6.1 产品安装步骤
6.2 接收器安装尺寸

6.3 接收器接线参考图

10. 保养与护理

1. Please use it in a dry environment with normal temperature and pressure to extend the
service life;
2. Please avoid using it in abnormal environments such as rain and water bubbles to extend
使用寿命;
3. Please keep the appearance of the handwheel clean to extend the service life;
4. 请避免挤压, 跌倒, 碰撞, 等等. to prevent damage to the precision parts
inside the handwheel or cause precision errors;
5. 如果长时间不使用, 请将手轮存放在干净安全的地方;
6. Pay attention to moisture and shock during storage and transportation.

11. Security Information

1. 使用前请仔细阅读说明. 非专业人员禁止
操作.
2. Please replace the battery in time when the battery is too low to avoid errors caused by
insufficient power causing the handwheel to be unable to operate.
3. 如果需要维修, 请联系制造商. 如果是自行修理造成的损坏,
制造商将不提供保修.