1. 12 按钮, 6 其中支持I/O信号.
2. 支持2.8英寸彩屏显示.
3. 支持1个9级轴选择开关, 最多支持6轴输出.
4. 支持1个三级倍频开关.
3D 五轴激光切割无线遥控：PHB06B-激光
描述
1.产品简介
The PHB06B-Laser enables wireless remote control operation of the CNC system via the Modbus TCP protocol, 支持 12 按钮, and supports real-time display of system coordinates and status.
2.产品功能
1. 12 按钮, 6 其中支持I/O信号.
2. 支持2.8英寸彩屏显示.
3. 支持1个9级轴选择开关, 最多支持6轴输出.
4. 支持1个三级倍频开关.
5. Supports one electronic remote control, 100 pulses/revolution.
6. Supports receiver Ethernet interface, Modbus TCP communication.
7. Supports standard Type-C charging, 5V-2A充电规范, built-in battery specifications 18650/12775mWh.
3.工作原理
PHB06B-Laser is connected to the user’s system via an Ethernet interface. It performs data interaction through the Modbus TCP protocol. The user system acts as the Modbus master station, which can transmit real-time system display coordinates and read information such as keys and axis selection of the PHB06B-Laser remote control, so as to realize real-time data communication.
笔记: For the specific protocol, please refer to the “3D 5-axis Laser Cutting – PHB06B – Laser – Modbus Protocol Description”.
4.产品规格
| 接收器电源电压 | DC5V-DC24V |
| Button lifespan | 1,000,000 时代 |
| 工作温度 |
-25℃ < x < 55℃
|
| 安全跌落高度 | 1 m |
| Receiver port | 以太网 |
| Number of buttons |
12
|
| 显示屏幕 |
2.8-inch color screen
|
| wireless communication frequency | 433MHz band |
| Receiver sensitivity |
-100分贝
|
| Handheld transmit power |
15分贝
|
| 无线通讯距离 | 100 meters barrier-free range |
| Rechargeable Battery Specification | Rechargeable Battery Specification |
| Charging base power supply voltage | 直流24V/1A |
|
Wired Charging Specification
|
Type-C charging port, DC 5V/2A |
5.产品功能介绍
笔记:
① Power Switch
Used to turn the remote control on and off.
② Enable buttons on both sides
The enable button must be pressed while holding the remote control.
③Button area
12 按钮
④ Axis Selection and Magnification Switch
One 9-gear axis selection switch; one 3-gear magnification switch.
⑤ Emergency Stop Switch
Remote control emergency stop switch.
⑥ Display Screen Area
It can display coordinates, status and other information.
⑦ Electronic Pulse Encoder
One electronic pulse encoder with 100 每转脉冲数.
⑧ Type-C Charging Port
It is used for connection between the charger and the remote control.
The handheld display includes a coordinate interface and a 6-point acquisition interface, which can be switched by pressing the ‘Next Page’ key
6. 产品配件图
7. Receiver and Wiring Ports
8. Configure network access
9. Test Instructions
10. Installation dimensions
接收器安装尺寸
单元: millimeters
Thickness: 29.6mm
11.维护和保养
1. 请在室温和压力下在干燥的环境中使用它以延长其使用寿命.
2. Do not use sharp objects to contact the button area to extend button life.
3. 请保持遥控器外观清洁，以延长其使用寿命.
4. 请避免挤压, 掉落, 或碰撞, ETC. to prevent damage to the precision components
5. 储存和运输过程中应避免受潮、震动.
12.安全信息
1. 请在使用前仔细阅读说明，并禁止非专业人员操作.
2. 如果您自行修理并造成损坏, 保修将失效.
