应用:用于各种工业设备
1.最大限度 26 焊机自动化焊接和焊接操作员。转动滚轮 1.采用跳频传输技术.
2.无障碍传输距离为 200 米.
3. 最大限度 4 模拟0-10V输出通道 (显示范围可定制): 支持 2 扩展隔离数字电位器输出通道;
4. 2 模拟输入; 并显示在遥控器上, 显示范围可定制.
5. 1 急停继电器输出常闭触点.
- 低功耗设计
- 易于使用
应用:用于各种工业设备
1.最大限度 26 焊机自动化焊接和焊接操作员。转动滚轮 1.采用跳频传输技术.
2.无障碍传输距离为 200 米.
3. 最大限度 4 模拟0-10V输出通道 (显示范围可定制): 支持 2 扩展隔离数字电位器输出通道;
4. 2 模拟输入; 并显示在遥控器上, 显示范围可定制.
5. 1 急停继电器输出常闭触点.
模型: DH01R-4W-26K
适用设备:various industrial equipment
笔记: 您可以选择三种天线之一. 默认标配吸盘天线.
笔记:
① DH01R series, if the suffix contains T, it means with emergency stop output;without T, it means without emergency stop output.
②If there is no analog output, there is no need to remark 0W or 0R; the analogquantities W1, W2, W3, and W4 default to 0-10V analog voltage output; at the same time, W1 and W2 can be expanded to 2 isolated digital potentiometer outputs, with a range of 0 -5K ohms, ½ watt; resolution: 20 ohms. The two digital potentials can be used to control the welding current and welding voltage of the welding machine. If the digital potentiometer output is required, user notes are required.
④Analog input, ranging from 1 to 2, indicating that there are 1 to 2 模拟输入(maximum 2 频道); when there is an analog input, you need to note the voltage range of the analog input (our receiver defaults to 0 -5V, the user can also note as 4-20 mA or 0-10V, 等等) and the corresponding display range of the analog quantity (for example: display 0-100 volts or 0-1000 amps)
These two analog quantities can be used as displays for welding current and welding voltage.
1)Maximum 26 焊机自动化焊接和焊接操作员。转动滚轮 1.采用跳频传输技术;
2)Maximum 4 模拟0-10V输出通道 (显示范围可定制): 支持 2 扩展隔离数字电位器输出通道;
3)2 analog inputs; 并显示在遥控器上, 显示范围可定制
4)1 channels of emergency stop relay output normally closed contacts;
5) Powered by 3 AA电池, low power consumption design;
6) Wireless operation distance is 200 米;
7)Protection grade IP67;
8)With cross switch operation, supports two 4-direction cross switches;
9)Back strap design.
W1 knob value: W1: 0-1000 (parameter adjustable 0-9999)
W2 knob value: W2: 0-5000 (parameter adjustable 0-9999)
W3 knob value: W3: 0-5000 (parameter adjustable 0-9999)
W4 knob value: W4: 0-5000 (parameter adjustable 0-9999)
ADC1 feedback display: 0-1000 (parameter adjustable 0-5000)
ADC2 feedback display: 0-1000 (parameter adjustable 0-5000)
低电压: 遥控器电池电量过低, 请更换电池.
网络掉线: 无线信号中断. 请检查接收器功率, 再次打开电源, 并重新启动遥控器.
1) Turn on the remote control
When the receiver is powered on, the receiver working indicator flashes; install two AA batteries in the remote control, 打开电源开关, and the display shows a value,表示启动成功. The receiver working indicator light becomes solid.
2)Switch and button functions
Any operation of the twist switch and button on the remote control can control the corresponding switch signal output point on the receiver. All switch signal output points on the receiver are normally open signals by default;
3)W1-W4 speed adjustment
Rotate the knobs in W1-W4 arbitrarily to operate the corresponding analog output signal or potentiometer signal at the receiver end. The analog output signal at the receiver end defaults to a 0-10V voltage signal, and the potentiometer signal defaults to 0-5K;
4) Emergency stop function
When the emergency stop button is pressed, all switch signal outputs are disconnected and the analog output is disconnected; after the emergency stop is released, all switch signals are restored and the analog output is restored; 5 seconds after the remote control is turned off, all switch signal outputs are disconnected and the analog quantities remain unchanged. When the remote control is turned on, the switch signal outputs automatically recover;
5)Parameter menu (users are prohibited from modifying it privately)
Some functions of the remote control can be adjusted through parameters. When the display W1=0, press the K9-B button 3 times in a row, and then press the K9-A button 3 times in a row to enter the parameter menu; K9-A and K9-B key to page through the menu and select parameters; hold down K1-A, and then press the K9-A/B button to modify parameters;
Exit the parameter menu: choose to save or not save, and then press the K1-A button to confirm the exit;
F1W1 range: The display range value of the W1 knob on the display screen, adjustable from 0 to 9999;
F2W2 range: The display range value of the W2 knob on the display screen, adjustable from 0 to 9999;
F3W3 range: The display range value of the W3 knob on the display screen, adjustable from 0 to 9999;
F4W4 range: The display range value of the W4 knob on the display screen, adjustable from 0 to 9999
F5A1 range: Display ADC1 feedback display range value, 0-5000 adjustable;
F6A2 range: Display ADC2 feedback display range value, 0-5000 adjustable;
Alarm current: Set the alarm value for ADC1 and ADC2 feedback display. When ADC1 and ADC2 exceed this value, the remote control display will alarm; when this value is 0,the alarm function is invalid;
本产品最终解释权归我司所有.
评价
目前还没有评论