无线电子手轮DWGP

描述

 

1.产品简介

无线电子手轮用于手动指导, 定位, tool setting and
other operations of CNC machine tools. 该产品采用无线传输技术,
消除传统的弹簧电线连接, 减少电缆引起的设备故障,
eliminating the disadvantages of cable dragging, oil stains, ETC。, and is more convenient to
operate. It is widely used in CNC machine tools such as gantry machining centers, gantry
vertical lathes, CNC gear processing machines, and can be adapted to a variety of CNC
systems on the market, such as Siemens, 三菱, Fanuc, syntec and other CNC system
brands.

2.产品功能

1. 采用433MHz无线通信技术, 无线操作距离为 80 仪表;
2. 采用自动跳跃功能, 使用 32 sets of wireless remote controllers at the
same time without affecting each other;
3. 支持紧急停止按钮, and after the handwheel is turned off, the emergency stop
button is still valid;
4. 支持 6 自定义按钮, 切换IO信号输出;
5. 支持6轴控制, 7-12 可以定制轴控制;
6. 支持1倍,10x, 100X控件，可以是最大可自定义的1000x;
7. Supports the enable button function, output switch l0 sianals. axis selection,maanification
and encoder.;
8. Support axis selection and magnification selection encoder output;
9. Support standard Type-C charging, 5V-2A charging specification, built-in battery specification
14500/1100mAh.

3.Product specifications

 

4.Product function introduction

 

笔记：
①施加停止按钮：
When the emergency stop button is pressed, the two emergency stop IO outputs on
the receiver are disconnected, and all handwheel functions are invalid. When the emergency
stop is released, the emergency stop IO output on the receiver is closed, and all handwheel
functions are restored; and after the handwheel is turned off, the emergency stop IO output
of the receiver is still valid when the emergency stop button is pressed.

②Enable button:
Press any one of the enable buttons on both sides, and the two groups of enable IO
outputs on the receiver will be turned on. Release the enable button and the enable IO
output will be turned off. In addition, you need to press and hold the enable button before
switching the axis selection ratio and shaking the handwheel. This function can be
canceled through the configuration software.
③Axis selection switch (power switch):
Press and hold the enable button and switch the axis selection switch to switch the
moving axis controlled by the handwheel. Switch this switch from OFF to any axis and
turn on the handwheel power.

④Pulse encoder:
按住启用按钮并摇动脉搏编码器以发送脉冲
信号控制机器轴的运动.

⑤Battery indicator:
The hand wheel power display, all bright means full power, all off means it is not
turned on or has no power, the first left grid flashes, indicating that the power is too low,
please charge in time.
⑥Signal Lights:
If the signal light is on, it means the handwheel is being operated and the signal is
normal; if the signal light is off, it means there is no operation, or it is being operated but
the wireless signal is not connected.

5.产品配件图

 

6.产品安装指南

6.1 产品安装步骤
1. Install the receiver in the electrical cabinet using the clips on the back, or install it in
the electrical cabinet using the screw holes at the four corners of the receiver.
2.请参阅我们的接收器接线图, 将其与您的现场设备进行比较, 并连接
通过电缆到接收器的设备.
3.接收器修复后, 配备了接收器的天线必须连接,
并且天线的外端必须安装或放置在电柜外面. 它
is recommended to place it on the top of the electrical cabinet for the best signal effect. It is
forbidden to leave the antenna unconnected or place the antenna inside the electrical cabinet,
这可能导致信号无法使用.
4. 最后, 打开手轮动力开关，您可以通过
手轮遥控器.

6.2 接收器安装尺寸

6.3 接收器接线参考图

7.Product Operation Instructions
1. The machine is powered on, the receiver is powered on, the receiver working indicator
light flashes, the wireless electronic handwheel has the battery installed, the battery cover
is fastened, the wireless electronic handwheel power switch is turned on, and the
handwheel power light is on;
2. Select the coordinate axis: Press and hold the enable button, switch the axis selection
switch, and select the axis you want to operate on;
3. Select magnification: Press and hold the enable button, switch the magnification switch,
and select the magnification level you need;
4. Moving axis: Press and hold the enable button, select the axis selection switch, select
the magnification switch, and then rotatethe pulse encoder to rotate the positive moving axis
clockwise and the negative moving axis counterclockwise;
5. Press and hold any custom button, and the corresponding button IO output of the
receiver will be turned on. Release the button to turn off the output;
6. 按下紧急停止按钮, the corresponding emergency stop IO output of the
receiver is disconnected, the handwheel function is disabled, release the emergency stop
按钮, the emergency stop IO output is closed, and the handwheel function is restored;
7. If the handwheel is not operated for a period of time, it will automatically enter sleep
mode to reduce power consumption. When it is used again, the handwheel can be
activated by pressing the enable button;
8. If the handwheel is not used for a long time,it is recommended to switch the handwheel
shaft to the OFF position, turn off the handwheel power, and extend the battery life.

8.Product Model Description

① ：DWGP represents the appearance style

② ：Pulse output parameters:
01: Indicates that the pulse output signals are A and B, and the pulse voltage is 5V; Pulse
quantity 100PPR;
02: Indicates that the pulse output signals are A and B, and the pulse voltage is 12V; Pulse
quantity 25PPR;
03: Indicates that the pulse output signal is A B、A-、B-； Pulse voltage 5V; Pulse quantity 1
00PPR;
04: Indicates a low-level NPN open circuit output, with pulse output signals of A and B; the
number of pulses is 100PPR;05: Indicates high-level PNP source output, pulse output signals
are A and B; pulse quantity is 100PPR;
③ : represents the number of axis selection switches, 6 represents 6 轴, 7 represents 7 轴.
④ : represents the type of axis selection switch signal, A represents point-to-point output signal,
B represents encoded output signal;

⑤ : represents the type of magnification switch signal,
A represents point-to-point output signal, B represents encoded output signal;
⑥ : represents the number of custom buttons, 6 represents 6 自定义按钮;
⑦ : represents the power supply for the system handwheel, 05 represents 5V power supply,
and 24 represents 24V power supply.

9.Product Troubleshooting

 

10. 维护和关怀

1. Please use it in a dry environment at room temperature and pressure to extend its service life;
2. Please avoid using in abnormal environments such as rain and water bubbles to extend the service life;
3. Please keep the appearance of the handwheel clean to extend its service life;
4. 请避免挤压, 跌倒, 碰撞, ETC. to prevent damage to the precision components inside
the handwheel or accuracy errors;
5. 如果很长一段时间没有使用, 请将手轮存放在干净安全的地方;
6.During storage and transportation, attention should be paid to moisture and shock resistance.

11.Safety Information

1. Please read the instructions carefully before use and prohibit non professionals from operating;
2. When the battery level is too low, please charge it in time to avoid errors caused by insufficient
battery and inability to operate the handwheel;

3. 如果需要维修, 请联系制造商. If the damage is caused by self repair, 制造商将不提供保修.