ワイヤーソーマシン自動切断ワイヤレスリモコン DH12S-P6S

説明

1.製品モデル

 

モデル: DH12S-P6S

適用される機器:wire saw/blade saw machine

2.製品アクセサリー図

注記: 3つのアンテナのいずれかを選択できます. 吸引カップアンテナはデフォルトで標準です.

3.リモコンスイッチの説明

4.DisplayContentの紹介

Main motor speed: Main: 0-50
Traveling motor speed: Line: 0-50
Maximum speed limit of automatic cutting traveling motor: Speed: 0-30
(パラメーターは調整可能です)
Automatic cutting main motor setting current: Setting: 28 (パラメーターは調整可能です)
Swing arm motor speed: Swing: 0-50

低電圧: リモートコントロールバッテリーが低すぎます, バッテリーを交換してください.

ネットワークがドロップされました: ワイヤレス信号が中断されます. 受信機の電源を確認してください, もう一度電源を入れてください, リモートコントロールを再起動します.

5.リモートコントロール機能操作手順

1）Turn on the remote control

When the receiver is powered on, the D2 power light on the receiver is always on, andthe D1 signal light starts to flash; install two AA batteries in the remote control, 電源スイッチをオンにします, and the display will show the motor speed, スタートアップが成功したことを示します.

2）Large motor and speed regulation/Main motor and speed regulation

Press and hold “Speed Regulation Enable”, turn the “フォワード/リバース” フォワードに切り替えます, and the receiver’s main motor will turn on;
Press and hold “Speed Regulation Enable”, turn the “フォワード/リバース” 逆に切り替えます, and the receiver’s main motor will reverse and turn on;Simply move the switch to the middle or reverse direction, and the main motor will stop immediately without pressing the speed control enable button;回転します “big motor” knob to adjust the speed regulation voltage of the receiver’s main motor inverter to 0-10V;

3）Traveling motor

Press and hold “Speed Adjustment Enable”, turn the “フォワード/リバース” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

回転します “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

Press and hold “Speed Adjustment Enable”, and then pull the “Swing Arm/Reverse” switch, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Press and hold the “speed adjustment enable” button and rotate the “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “フォワード/リバース” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (ユーザーは許可なく変更することを禁止されています)

Enter the parameter menu:In manual mode, when the main motor speed is 0, フォワード/リバーススイッチを3回続けて押します, and then push it down three times in a row to enterthe parameter menu;
パラメーターメニューを終了します: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, デフォルト 800, unit milli second,変更は禁止されています;
減速パラメーター: 切断電流の変化値がこの値を超える場合, rapid deceleration begins, unit Ampere;
加速A1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
減速A2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, 変更は禁止されています;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, 変更は禁止されています;
最大電流: The range of main motor feedback current, unit Ampere;
最大ホスト: Remote control main motor speed adjustment display range;
最大のウォーキング: Invalid parameter;
速度制限オフセット: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: 自動切断, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.リモートコントロールの電気特性

7.リモートコントロールサイズ

この製品の最終的な解釈の権利は、当社にのみ属します.