応用:クローラーワイヤーソーマシンに特別に使用されます
1.Supports automatic cutting mode, automatically adjusts the walking speed of the small motor according to the large motor current, and achieves automatic cutting control.
2.バリアフリー送信距離はです 200 メーター.
3. Supports dual speed regulation for large motors and small motors.
4. Support small motor turning in place.
5. Supports left and right wheel small motor linear correction.
モデル: DH12S-LD
適用される機器:crawler wire saw machine
注記: 3つのアンテナのいずれかを選択できます. 吸引カップアンテナはデフォルトで標準です.
Large motor speed：S1：0-50
Small motor speed: S2: 0-50
Maximumspeedlimitofautomatic cuttingsmallmotor:F:0-30(parametersadjustable)
Automatic cutting maximum current: Ic: 0-35 (パラメーターは調整可能です)
Linear correction value: Df: -99-99 (1 unit is about 0.02V)
低電圧: リモートコントロールバッテリーが低すぎます, バッテリーを交換してください.
ネットワークがドロップされました: ワイヤレス信号が中断されます. 受信機の電源を確認してください, もう一度電源を入れてください, リモートコントロールを再起動します.
1.Turn on the remote control
When the is powered on, the RF-LED light on the receiver starts to flash;install two AA batteries in threceiver e remote control, 電源スイッチをオンにします, andthe display will show the motor speed, スタートアップが成功したことを示します.
2.Large motor and speed regulation
回転します “フォワード/リバース” フォワードに切り替えます, the receiver’s large motor will turn on, and the display will show forward
回転します “フォワード/リバース” 逆に切り替えます, the large motor of the receiver will turn on in reverse, and the display will show reverse
回転します “large motor speed adjustment” knob to adjust the receiver’s large motor speed adjustment output voltage 0-10V;
3.Small motor and speed regulation
Move the “フォワード/リバース” フォワードに切り替えます, the left wheel forward and right wheel forward of the receiver are turned on, and the display shows forward
回転します “フォワード/リバース” 逆に切り替えます, the left wheel reverse and right wheel reverse of the receiver are turned on, and the display shows reverse
4.Turn left and right
回転します “Left/Right” switch to left, the receiver’s right wheel will forward and turn on,and the display will show left
回転します “turn left/right” switch to turn right, the left wheel of the receiver will forward and turn on, and the display will show turn right
5.Turn in place
手動モードで:
Turn left in place: 押し続けます “Enable” button, 回転します “Left/Right Turn” switch to left, the left wheel backward and right wheel forward of the receiver are turned on,and start turning left in place;
Turn right in place: 押し続けます “Enable” button, 回転します “Left/Right Turn” switch to right, the left wheel forward and right wheel reverse of the receiver are turned on, and the receiver starts to turn right in place;
6.Small motor speed limit adjustment
In automatic mode: press and hold the “Enable” ボタンと回転します “Small Motor Speed Adjustment” to adjust the maximum speed of the small motor during automatic cutting;
7.自動切断
The first step is to start the big motor; the second step is to switch the mode switch to “Auto”; the third step is to start the small motor and the screen will display “Cutting Auto”,indicating that it has entered the automatic cutting mode;
8. Straight line correction
When the left and right walking motors are moving forward and backward, the left and right speeds are inconsistent, and the straight-line walking deviates. You can use the linear correction function of the remote control to fine-tune the speed of the left and right wheels;
Correction principle: Through the correction function, the speed of the left wheel is fine-tuned to reach the same speed as the right wheel, so as to synchronize the speed of the left and right wheels and eliminate the deviation;
Deviation correction operation method: 手動モードで, press and hold the “Enable” ボタンと回転します “Small Motor Speed Regulation”;
Rotate clockwise to increase the left wheel speed voltage and the correction value on the display screen will increase;
Rotate counterclockwise to reduce the left wheel speed voltage and the display correction value to decrease;
Correction range: Correction value -90 to 90; correction voltage of one correction unit is about 0.02V;
9. Parameter menu (ユーザーは許可なく変更することを禁止されています)
Some functions of the remote control can be adjusted through parameters. 手動モードで, when the small motor speed S2 is 10, フォワード/リバーススイッチを3回続けて押します, and then push it down three times in a row to enter the parameter menu;
パラメーターメニューを終了します: choose to save or not save, then press the enable button to confirm the exit;
最大電流: the operating rated current of the cutting motor is 80% of this currentt;
Speed control parameters: automatic cutting control parameters, デフォルト 800, 変更は禁止されています;
減速パラメーター: automatic cutting control parameter. 切断電流の変化値がこの値を超える場合,deceleration begins.
加速A1: automatic cutting control parameter, when the cutting current is lower than the set cutting current, the speed of acceleration;
減速A2: automatic cutting control parameter, when the cutting current is higher than the set
cutting current, the speed of deceleration;
Automatic knife retraction: invalid;
Start self-locking: 0, no self-locking; 1, self-locking. Press the enable key + forward and reverse to take effect and self-lock.
最大のウォーキング: the maximum speed of the small motor.
Cutting current: set the maximum current of the main motor for automatic cutting. If the feedback current exceeds this value, it will start to decelerate.
Default speed limit: the default maximum speed of automatic cutting speed when turning on the machine.
Automatic mode: 0, the automatic switch is automatically controlled; 1, the automatic switch controls the automatic IO output point.
速度制限オフセット: the maximum speed of the small motor during automatic cutting.
最大ホスト: maximum speed of large motor.
この製品の最終的な解釈の権利は、当社にのみ属します.
