電線鋸機自動切割無線遙控DH12S-P6S

描述

1.產品型號

模型: DH12S-P6S

適用設備:繩鋸/片鋸機

2.產品配件圖

筆記: 您可以選擇三種天線之一. 默認標配吸盤天線.

3.遙控開關說明

4.顯示內容介紹

主電機轉速: 主要的: 0-50
行走電機轉速: 線: 0-50
自動切割行走電機最高速度限制: 速度: 0-30
(參數可調)
自動切割主電機設定電流: 環境: 28 (參數可調)
擺臂電機轉速: 搖擺: 0-50

低電壓: 遙控器電池電量過低, 請更換電池.

網絡掉線: 無線信號中斷. 請檢查接收器功率, 再次打開電源, 並重新啟動遙控器.

5.遙控功能操作說明

1）打開遙控器

當接收機開機時, 接收器上的D2電源燈常亮, andthe D1 signal light starts to flash; 在遙控器中安裝兩節 AA 電池, 打開電源開關, 顯示屏將顯示電機轉速, 表示啟動成功.

2）大電機及調速/主電機及調速

按住 “調速使能”, 轉動 “前進/後退” 切換到轉發, 接收器主電機將開啟;
按住 “調速使能”, 轉動 “前進/後退” 切換到反向, 接收器主電機反轉並啟動;只需將開關移至中間或反向即可, 不按調速使能按鈕，主電機立即停止;旋轉 “大電機” 旋鈕調節接收機主電機逆變器調速電壓0-10V;

3）行走馬達

按住 “速度調節啟用”, 轉動 “前進/後退” switch to forward or backward, and the walking motor will move at a high speed of 50;

4）Swing arm motor and speed regulation

Turn the “Swing Arm/Reverse” switch to swing arm or retreat, and the receiver’s swing arm motor starts; then rotate the “Speed Adjustment” knob to adjust the swing arm motor speed;

按住 “速度調節啟用”, and then pull the “Swing Arm/Reverse” 轉變, the swing arm motor will move at a high speed of 50;

5）Travel motor speed limit adjustment

Press and hold the “speed adjustment enable” button and rotate the “speed adjustment” to adjust the maximum speed limit of the traveling motor during automatic cutting;

6） Automatic cutting

The first step is to start the main motor; the second step is to adjust the maximum speed limit of the walking motor; the third step is to move the “forward/reverse” switch forward or backward to enter the automatic cutting mode;

7） Parameter menu (users are prohibited from modifying it without permission)

Enter the parameter menu:In manual mode, when the main motor speed is 0, push the forward/reverse switch up three times in a row, and then push it down three times in a row to enterthe parameter menu;
Exit the parameter menu: Turn the speed adjustment knob, select save or not save, and press the enable button to confirm;
Rated current: The maximum value of the main motor current, unit Ampere;
Speed adjustment parameters: Automatic cutting control parameters, default 800, unit milli second,modification is prohibited;
Deceleration parameter: When the cutting current change value exceeds this value, rapid deceleration begins, unit Ampere;
Acceleration a1: When the cutting current is lower than the set cutting current, the speed value increased by each acceleration of the walking motor;
Deceleration a2: When the cutting current is higher than the set cutting current, the speed value reduced by each deceleration of the walking motor;
Swing arm current: Default value, modification is prohibited;
Stop time: After the automatic mode current overload shutdown, the current will be detected again after a period of time. If it is less than the set current, the walking motor will automatically start; unit second, default value, modification is prohibited;
Maximum current: The range of main motor feedback current, unit Ampere;
Maximum host: Remote control main motor speed adjustment display range;
Maximum walking: Invalid parameter;
Speed limit offset: During automatic cutting, the remote control display walking motor speed limit = 50% of this parameter;
Increase sensitivity: When the main motor feedback current increases, each time the increase exceeds this value, the walking motor accelerates;
Decrease sensitivity: When the feedback current of the main motor decreases, and each time the decreasing value exceeds this value, the walking motor decelerates;
Sensitivity offset: Add and subtract the offset increment of the sensitivity parameter;
Set current: Automatic cutting, the threshold of main motor feedback current. If this value is exceeded,the walking motor starts to decelerate;Below this value, the walking motor starts to accelerate;unit: Ampere;
Idling exit: When the automatic mode starts, if the main motor feedback current is less than this value,it will be in the idling mode.If it is greaterthan this value, it will exit the idling mode and enter the cutting mode.Unit is ampere;
No-load current:When automatic mode starts, if the main motor feedback current is less than this value,it is in no-load mode.If it is greaterthan this value, it will exit the no-load mode and enter the cutting mode.Unit is Ampere;
Swing arm speed: Initial speed of swing arm motor when starting up;
Cutting mode: Switch between blade saw and wire saw modes, and the parameters will switch accordingly after the switch; in blade saw mode, the remote control display adds a swing arm motor, while in wire saw mode, there is no swing arm motor;
Debounce time: When the main motor feedback current exceeds the stop current, the feedback current will be continuously detected. The debounce time is the duration of this continuous detection.After this time, if the main motor current still exceeds the stop current, the walking motor will stop;otherwise, the walking motor will stop. The motor will keep going;
Stop current: The main motor feedback current exceeds this value, and the walking motor will stop;Unit is Ampere;
Offset default: The initial value of the walking motor speed limit when the remote control is turned on = 50% of this value;

6.Remote control electrical characteristics

7.Remote control size

The final interpretation right of this product belongs only to our company.